Icom AP-12 instruction manual Connecting to a LAN, Procedure, About Dhcp server detection

Page 24

2 OBTAINING AN IP ADDRESS FROM THE DHCP SERVER

2-1 Connecting to a LAN

This section enables a DHCP server to assigns an IP address automatically.

[Procedure]

qConnect the AP-12 and LAN with the supplied patch cable.

wConnect the AC adapter to the AC outlet to turn the AP-12 power ON.

POWER indicator and wired LAN indicator on the top panel lights.

Wireless LAN transmission indicator on the top panel flashes.

192.168.1.10

Connect to the LAN with a DHCP server, such as a router type modem.

Server:192.168.1.1

Automatically assigned range

192.168.1.10 to 192.168.1.15

HUB

=

⋅ ⋅

AP-12

Cross Port

Ferrite core

Patch cable (supplied)

When connecting to the broadband router, connect the Ethernet cable from the AP-12 to the [LAN] port of the router.

AP-12

192.168.1.11192.168.1.12

DAbout DHCP server detection

The AP-12 searches the DHCP server automatically to connect with a wired LAN in which the DHCP server exists in. When no DHCP server is found within 30 sec. (approx.) from power ON, the default IP address is used for the AP-12.

The default IP address is “192.168.0.1”. However, when a DHCP server is found in the network, the AP-12 use the IP address obtained from the server.

Once the AP-12 power is turned OFF, then ON again, the AP-12 starts searching for the DHCP server for 30 sec. (approx.) again.

10

Image 24
Contents AP-12 Page Introduction About exchanging the AP-12 or the PC connected to the AP-12Foreword Features AP-12 General Precautions Following notational conventions are used in this manualAccessories Table of Contents IP Configuration …………………………………51-56 Safety Precautions Rcaution General Precautions AC adapterPage Wireless functional modes …………………………………………………………2 Installation location …………………………………………………………………7About the Ethernet card ……………………………………………………………8 Wireless functional modes Access point mode defaultAbout a MAC address Unit description Accessory attachment To avoid interference AC adapter Ethernet cableInstallation location Examples of recommended installationExamples of installation not recommended Installation precautionsAbout the Ethernet card Desktop PCChapter Connecting to a LAN ProcedureAbout Dhcp server detection Installing AP-12 Manager ClickClick Finish Installation is now completed Starting AP-12 Manager About AP-12 iconAP-12 Manager Setting Screen To exit AP-12 ManagerFixed IP Address Connecting to the PC Using Easy Setting Wizard When no access point is found Enter Click About IP AddressEasy Setting Wizard will restart automatically Click Next 0Click Next Select Click ESS ID is changeable later. See p for details 7Click Finish Installing AP-12 Manager Click Finish Installation is now completed Displays the connected AP- 12’s IP address To exit the AP-12 Manager AP-12 Manager Settings screen Page AP-12 Manager screen descriptions …………………………………………32 Settings AP-12 Manager screen descriptionsBe entered default LG Remote MAC Address Preferred BssidHidden wireless terminals Communication channelsIP Configuration MAC security Wep settings ……… Key generator …… Wep SecurityWEP Key Setting Examples- 64-bit encryption Show Station Version Information Options Default settings MAC security Wep SecurityUninstalling AP-12 Manager Setting Examples Access point mode Bridge mode a Peer-to-Peer Common settingsFunctional mode Select Bridge Mode a Individual settingsBridge mode B Client Mode Common settingAP-12 1 and 2 settings Functional mode Select Bridge Mode B Preferred BSS IDBridge mode C Multi-site All AP-12s settingsFunctional mode Page IP Configuration For Windows XP Click Enter For Windows 98/98SE/Me For Windows Click Glossary ……………………………………………………………………………70 Troubleshooting Program Possible Cause SolutionDhcp Connecting the AP-12 and HUB Verifying the connection to the AP-12Connect to the Cross Port Connect to the Cascade PortWhen using Easy Setting Wizard D When using AP-12 Manager Failure in searching for the AP-12Click Verify Set Click Windows XP Procedure IP address confirmationWindows 98/98SE/Me Procedure Windows 2000 ProcedureWireless terminal preparation Connection to the router type modemConnection to the router type modem Procedure When communication has failedRouter Type Modem Specifications LAN interface Transmission rateUser interface System requirementsBSS ID Basic Service Set-IDentifier Glossary10BASE-T Memo Memo