Icom AP-12 instruction manual Connecting to the PC, Procedure

Page 30

3 FIXED IP ADDRESS SETTING

3-1 Connecting to the PC

[Procedure]

qConnect the AP-12 and the PC with the supplied crossover cable.

•Use the supplied patch cable (3 m: 9.8 ft) when connecting the AP-12 and the PC via a HUB.

NOTE: DISCONNECT THE PC FROM THE EXISTING LAN.

When the PC is connected to the existing LAN, the AP-12 searches the DHCP server and uses the IP address obtained from the server according to the default setting.

wConnect the supplied AC adapter to the AP-12 and an AC outlet.

•The Power indicator lights.

•The wireless LAN indicator flashes.

eStart up the PC.

•The wired LAN indicator on the top panel lights.

Check the Ethernet cable if the wired LAN indicator does not light.

Ferrite core (supplied)
Ethernet cross	Ferrite core (supplied)
cable (supplied)	AC adapter
	AC adapter
	(supplied)

AC outlet

Ethernet port

R

AP-12

DC jack

16

Image 30

Contents AP-12 Page Introduction About exchanging the AP-12 or the PC connected to the AP-12Foreword Features AP-12 General Precautions Following notational conventions are used in this manualAccessories Table of Contents IP Configuration …………………………………51-56 Safety Precautions Rcaution General Precautions AC adapterPage Wireless functional modes …………………………………………………………2 Installation location …………………………………………………………………7About the Ethernet card ……………………………………………………………8 Wireless functional modes Access point mode defaultAbout a MAC address Unit description Accessory attachment To avoid interference AC adapter Ethernet cableExamples of installation not recommended Installation locationExamples of recommended installation Installation precautionsAbout the Ethernet card Desktop PCChapter Connecting to a LAN ProcedureAbout Dhcp server detection Installing AP-12 Manager ClickClick Finish Installation is now completed Starting AP-12 Manager About AP-12 iconAP-12 Manager Setting Screen To exit AP-12 ManagerFixed IP Address Connecting to the PC Using Easy Setting Wizard When no access point is found Enter Click About IP AddressEasy Setting Wizard will restart automatically Click Next 0Click Next Select Click ESS ID is changeable later. See p for details 7Click Finish Installing AP-12 Manager Click Finish Installation is now completed Displays the connected AP- 12’s IP address To exit the AP-12 Manager AP-12 Manager Settings screen Page AP-12 Manager screen descriptions …………………………………………32 Settings AP-12 Manager screen descriptionsBe entered default LG Remote MAC Address Preferred BssidHidden wireless terminals Communication channelsIP Configuration MAC security Wep settings ……… Key generator …… Wep SecurityWEP Key Setting Examples- 64-bit encryption Show Station Version Information Options Default settings MAC security Wep SecurityUninstalling AP-12 Manager Setting Examples Access point mode Functional mode Select Bridge Mode a Bridge mode a Peer-to-PeerCommon settings Individual settingsAP-12 1 and 2 settings Bridge mode B Client ModeCommon setting Functional mode Select Bridge Mode B Preferred BSS IDBridge mode C Multi-site All AP-12s settingsFunctional mode Page IP Configuration For Windows XP Click Enter For Windows 98/98SE/Me For Windows Click Glossary ……………………………………………………………………………70 Troubleshooting Program Possible Cause SolutionDhcp Connect to the Cross Port Connecting the AP-12 and HUBVerifying the connection to the AP-12 Connect to the Cascade PortWhen using Easy Setting Wizard D When using AP-12 Manager Failure in searching for the AP-12Click Verify Set Click Windows XP Procedure IP address confirmationWindows 98/98SE/Me Procedure Windows 2000 ProcedureWireless terminal preparation Connection to the router type modemConnection to the router type modem Procedure When communication has failedRouter Type Modem Specifications User interface LAN interfaceTransmission rate System requirementsBSS ID Basic Service Set-IDentifier Glossary10BASE-T Memo Memo