Emulex 355 manual Initial Switch Setup, Log in to the Switch, Change the Password

Page 18

EMULEX MODEL 355 SAN STORAGE SWITCH

CHAPTER 3: SWITCH MANAGEMENT

USER’S GUIDE

Initial Switch Setup

Once a network connection has been established with the switch and an instance of the Web Manager is open, some basic switch configuration tasks are recommended:

•Log in to the switch.

•Change the switch’s password.

•Verify the switch’s date and time settings.

•Change the switch’s name.

For additional information on Web Manager features and functionality, see “Managing the Switch” on page 17 and “Monitoring the Switch” on page 45.

Step 1: Log in to the Switch

The switch incorporates a password-level security system to prevent unwanted changes to the current switch configuration. In order to make any changes to the switch, users must be logged in to the switch.

To log in to the switch:

1.Click Login on any Web Manager page.

A message box appears confirming the login request.

2.Click OK.

The switch login page appears.

3.Enter the switch’s password.

The default password is "password".

4.Click Log In.

A message page appears while the page is loading. If the page fails to load in the indicated time, click Continue.

See “Logging in to the Switch” on page 18 for additional information.

Step 2: Change the Password

The default password is set at the factory to “password”. Change the default password to secure the switch and guarantee that any configuration changes are only performed by registered users.

To change the password:

1.Click Switch > Password.

The Switch Password page appears.

2.Enter the new password in the New Password text box.

Note: The password must be between 6 and 25 characters in length and is case sensitive.

3.Enter the new password again in the Confirm New Password text box.

4.Click Submit.

A message box appears confirming the change to the switch’s configuration.

5.Click OK.

The Password set success message appears confirming that the new password was saved and activated.

See “Changing the Password” on page 23 for additional information.

EMULEX CORPORATION

15

PART NUMBER 00041407-002 REV. B

Page 17 Page 19
Image 18
Page 17 Page 19
Contents Model ART N Umber 00041407-002 R EV. B Table of Contents Chapter Introduction OverviewFeatures Inspeed TechnologyInstallation Preparation To unpack the switchSwitch can be installed in a rack or placed on a desktop Rack InstallationSwitch Installation To install the switches in the trayDesktop Installation To place the switch on a desktopUL Guidelines for Mounting Equipment in a Rack Switch Leds Ethernet LEDsEthernet LEDs indicate the network connection status System LEDs Port LEDs SFP Status Port BypassedRemoving an SFP Installing an SFPAttaching a Device to the Switch SFP CompatibilityBooting the Switch and SAN To boot the switch and SANChapter Switch Management Configuring the Network Interface Getting StartedTo connect through a serial interface Cancel Connecting to the Web ManagerCommand Button Description Submit Web Manager OverviewDocumentation Command Button Description RebootLogin/Logout RefreshChange the Password Initial Switch SetupLog in to the Switch To log in to the switchTo set the date and time settings Change the Switch NameTo view the current date and time Click Switch Date & Time To change the switch name Click Switch ConfigurationManaging the Switch Frequent Switch Configuration TasksTo change a switch setting Logging in to the SwitchConfiguring the Switch Settings To reset the switchGeneral Switch Settings Switch IdentificationNetwork Location Version Information Switch SpeedTo change the switch speed Click Switch Configuration Blocking ARBSetting Snmp Traps To configure an Snmp trapConfiguring Date and Time Settings To change the time Click Switch Date & TimeTo synchronize time with the host system Click Host Time Changing the Password Switch Password page appearsOpening a Telnet Session Adjusting the Switch Thresholds Switch Thresholds page appearsTo change switch thresholds or time intervals Configuring the Port Smart Settings To view the Port Smart Settings Click Port Smart SettingsPort Smart Settings page appears Default Smart Settings To set all ports to the currently selected Smart Setting Creating Custom Smart SettingsTo assign a Smart Setting to one or more ports To create a custom Smart SettingTo rename a custom Smart Setting Smart Setting AssignmentsTo modify a custom Smart Setting To delete a custom Smart SettingPre-Insertion Testing Following settings are availablePort Information Manager Setting Description Stealth Intelligent ChangeChange Notifications Change Notification onPort Recovery Setting Description Port Control Managing Firmware and Configuration FilesDiagnostics Bypass on Clock DeltaSwitch Firmware Files Switch Configuration FilesRestoring the Factory Default Settings To restore the factory default configurationOne-Step Zoning To remove a port from a zone To add ports to a zoneTo activate zoning To remove all ports from a zoneSingle-Switch Zoning 13 Devices in a Single ZoneAdding Devices to Multiple Zones To add storage devices to multiple zonesMultiple Switch Zoning 17 Devices in Multiple Zones Across Multiple SwitchesRecovering a Bad Zone Automatically Alpa ZoningConnecting Ports Through Hard Zoning To set up Hard ZoningCascading Switches String CascadesTree Cascades Automatic Trunking 22 Automatic Trunking exampleLoad Balancing 23 Advanced Functions Automatic TrunkingLoad Indicators To change the load balancing settingsFairness and Prioritization Switch Information Viewing Switch StatusMonitoring the Switch Current status is provided for the following itemsYellow Port Utilization and HealthPort Color Indication Green RedEvent Log Messages page appears To view the event log Click Switch Event LogViewing the Event Log Last time the event log was polled appears at the topViewing Port Information To view port information Click Port InformationPort Information page appears Value Description High Viewing Port UtilizationPort Utilization page appears AverageViewing Port Diagnostics Port Diagnostics page appearsManual Port Operation To save diagnostic informationTo reset a port Click Advanced Functions Diagnostics Port To clear the countersViewing Ordered Sets Change CRC ErrorDetection Indication F7 Initialization Notification UnknownTroubleshooting Device Connections Troubleshooting Management Connections Port Bypass Conditions and RecoveryDefault Smart Setting Attributes Fibre Channel References Appendixes Switch Specifications Operating ConditionsTo connect through a network interface Connecting to the CLILogging in and OUT To log in to the CLIUsing the CLI Frequent Switch Configuration TasksCLI Commands Severity Description Level Event Event Message SeverityInterswitch link added/removed Error during Port DiscPort Ptbi failed due to timeout LIP Cycle TimeoutArbitrated Loop Physical Addresses Hex DecimalArbitration Alpa or Arbitrated LoopPhysical Address Current Fill WordIndex SFP Part Number 00041407-002 REV. B
Related manuals
Manual 74 pages 23.77 Kb

355 specifications

The Emulex 355 is a high-performance network interface card (NIC) designed specifically for data centers requiring advanced connectivity, reliability, and speed. With the rapid evolution of data transmission technology, the Emulex 355 stands out due to its robust features and capabilities that cater to the demands of modern IT infrastructures.

One of the key features of the Emulex 355 is its support for 10 Gigabit Ethernet, which allows for significantly faster data transfer rates compared to standard Gigabit connections. This increased bandwidth is essential for handling large volumes of data traffic, particularly in virtualized environments and cloud computing applications. Its high throughput ensures that data can be transmitted rapidly across networks, minimizing latency and improving overall performance.

The Emulex 355 employs advanced technologies such as iSCSI Offload and FCoE (Fibre Channel over Ethernet), which help enhance data processing efficiency. These technologies allow the card to offload processing tasks from the host system's CPU, reducing the load on server resources and optimizing performance. The result is a more efficient system that can handle more concurrent connections and processes without being overwhelmed.

In addition to speed and efficiency, reliability is paramount in data center operations. The Emulex 355 includes features like error detection and correction, ensuring data integrity during transmission. Built-in redundancy and failover capabilities safeguard against potential network disruptions, allowing for continuous availability of services—a crucial aspect in mission-critical environments.

The Emulex 355 also offers support for various robust networking protocols, enabling seamless integration into existing network infrastructures. Its compatibility with multiple operating systems and virtualization platforms, such as VMware and Microsoft Hyper-V, further enhances its versatility.

Another notable characteristic of the Emulex 355 is its energy-efficient design. It is optimized for lower power consumption without sacrificing performance, aligning with contemporary efforts to reduce the carbon footprint in data centers.

In conclusion, the Emulex 355 NIC is a powerful solution equipped with features that address the complex demands of modern data centers. Its combination of speed, reliability, and efficiency, along with advanced technologies, makes it a preferred choice for organizations looking to enhance their network capabilities and ensure smooth, uninterrupted operations.
Top Page Image Contents