Emulex 355 manual Setting Snmp Traps, To configure an Snmp trap

Page 24

EMULEX MODEL 355 SAN STORAGE SWITCH	CHAPTER 3: SWITCH MANAGEMENT
USER’S GUIDE

Setting SNMP Traps

Simple Network Management Protocol (SNMP) uses traps to transmit information to SNMP-based network administration programs. The Switch SNMP Trap Configuration page displays information on the switch’s current SNMP trap configuration.

To view the SNMP trap configuration page, click Switch > SNMP Traps.

Figure 3-4: Switch SNMP Trap Configuration page

To configure an SNMP trap:

1.Enter the Trap IP address for the device to which the trap information will be sent.

2.Enter the Trap Port number.

This value is usually set to "162" for Windows and Apple-based networks.

3.Select the State.

State	Description

Active	The trap sends messages to the host identified in the IP Address
	selection.

Inactive	The trap is not operational.

Delete	The trap will be deleted from the table once changes are saved.

4. Click Submit.

When editing a registered IP address, delete the current IP address and create a new entry for the revised IP address.

EMULEX CORPORATION

21

PART NUMBER 00041407-002 REV. B

Image 24

Contents Model ART N Umber 00041407-002 R EV. B Table of Contents Chapter Introduction OverviewFeatures Inspeed TechnologyInstallation Preparation To unpack the switchRack Installation Switch InstallationSwitch can be installed in a rack or placed on a desktop To install the switches in the trayDesktop Installation To place the switch on a desktopUL Guidelines for Mounting Equipment in a Rack Switch Leds Ethernet LEDsEthernet LEDs indicate the network connection status System LEDs Port LEDs SFP Status Port BypassedInstalling an SFP Attaching a Device to the SwitchRemoving an SFP SFP CompatibilityBooting the Switch and SAN To boot the switch and SANChapter Switch Management Configuring the Network Interface Getting StartedTo connect through a serial interface Connecting to the Web Manager Command Button Description SubmitCancel Web Manager OverviewCommand Button Description Reboot Login/LogoutDocumentation RefreshInitial Switch Setup Log in to the SwitchChange the Password To log in to the switchChange the Switch Name To view the current date and time Click Switch Date & TimeTo set the date and time settings To change the switch name Click Switch ConfigurationManaging the Switch Frequent Switch Configuration Tasks Logging in to the Switch Configuring the Switch Settings To change a switch setting To reset the switchGeneral Switch Settings Switch IdentificationNetwork Location Switch Speed To change the switch speed Click Switch ConfigurationVersion Information Blocking ARBSetting Snmp Traps To configure an Snmp trapConfiguring Date and Time Settings To change the time Click Switch Date & TimeTo synchronize time with the host system Click Host Time Changing the Password Switch Password page appearsOpening a Telnet Session Adjusting the Switch Thresholds Switch Thresholds page appearsTo change switch thresholds or time intervals Configuring the Port Smart Settings To view the Port Smart Settings Click Port Smart SettingsPort Smart Settings page appears Default Smart Settings Creating Custom Smart Settings To assign a Smart Setting to one or more portsTo set all ports to the currently selected Smart Setting To create a custom Smart SettingSmart Setting Assignments To modify a custom Smart SettingTo rename a custom Smart Setting To delete a custom Smart SettingPre-Insertion Testing Following settings are availablePort Information Setting Description Stealth Intelligent Change Change NotificationsManager Change Notification onPort Recovery Managing Firmware and Configuration Files DiagnosticsSetting Description Port Control Bypass on Clock DeltaSwitch Firmware Files Switch Configuration FilesRestoring the Factory Default Settings To restore the factory default configurationOne-Step Zoning To add ports to a zone To activate zoningTo remove a port from a zone To remove all ports from a zoneSingle-Switch Zoning 13 Devices in a Single ZoneAdding Devices to Multiple Zones To add storage devices to multiple zonesMultiple Switch Zoning 17 Devices in Multiple Zones Across Multiple SwitchesRecovering a Bad Zone Automatically Alpa ZoningConnecting Ports Through Hard Zoning To set up Hard ZoningCascading Switches String CascadesTree Cascades Automatic Trunking 22 Automatic Trunking exampleLoad Balancing 23 Advanced Functions Automatic TrunkingLoad Indicators To change the load balancing settingsFairness and Prioritization Viewing Switch Status Monitoring the SwitchSwitch Information Current status is provided for the following itemsPort Utilization and Health Port Color Indication GreenYellow RedTo view the event log Click Switch Event Log Viewing the Event LogEvent Log Messages page appears Last time the event log was polled appears at the topViewing Port Information To view port information Click Port InformationPort Information page appears Viewing Port Utilization Port Utilization page appearsValue Description High AverageViewing Port Diagnostics Port Diagnostics page appearsTo save diagnostic information To reset a port Click Advanced Functions Diagnostics PortManual Port Operation To clear the countersViewing Ordered Sets CRC Error Detection Indication F7 InitializationChange Notification UnknownTroubleshooting Device Connections Troubleshooting Management Connections Port Bypass Conditions and RecoveryDefault Smart Setting Attributes Fibre Channel References Appendixes Switch Specifications Operating ConditionsConnecting to the CLI Logging in and OUTTo connect through a network interface To log in to the CLIUsing the CLI Frequent Switch Configuration TasksCLI Commands Severity Description Level Event Event Message SeverityError during Port Disc Port Ptbi failed due to timeoutInterswitch link added/removed LIP Cycle TimeoutArbitrated Loop Physical Addresses Hex DecimalAlpa or Arbitrated Loop Physical AddressArbitration Current Fill WordIndex SFP Part Number 00041407-002 REV. B

Related manuals

Manual 74 pages 23.77 Kb