Bissell 7950 Brush Belt or Pump Belt is off or broken, Turn the machine OFF and unplug from

Page 21

Troubleshooting (continued)

DirtLifter PowerBrush does not turn.

Possible Causes

1The Brush Belt or Pump Belt is off or broken.

Remedies

1Turn the machine OFF and unplug from

the outlet. To check if the Brush Belt or Pump Belt has broken, you will need a flat head screwdriver. Insert the blade end into the lower slot of the Belt Access door to release the lower snap. If necessary, insert the blade end into the upper slot to release the upper snap. Examine the belt for breakage. If broken refer to pages 18-19.

Carpet Protector is not spraying.

Possible Causes

1Tank not connected properly to the tool.

2Solution clogging the Spray trigger.

3Applicator tool spray is blocked.

4SmartMix not set on water/rinse

carpet protector setting.

5ReadyTool dial not set on tool setting.

Remedies

1Follow instructions on cartridge assuring proper fit.

2Soak applicator tool only in hot water. Spray without the cartridge attached to purge any residual Solution left in the tool.

3Soak applicator tool only in hot water.

Spray without the cartridge attached to purge any residual Solution left in the tool.

4Set to proper setting.

5Set to tool setting.

Cleaner not picking up solution.

Possible Cause

1Ready Tools dial may be at the wrong setting for the cleaning job.

2Nozzle Window may not be properly attached.

3Tank-in-Tank lid is not properly installed.

4Tank-in-Tank is not properly seated.

5Poor tool position. (Hand held attachments only).

6Tank-in-Tank has picked up maximum dirty water.

Remedies

1Set ReadyTools dial to either Tools or PreTreat or Floor Cleaning.

2Press down firmly on the black oval gasket at the top window to make sure the two tabs on the back of the Nozzle Window are snapped into the mating slots in the main housing.

3Re-install lid; refer to page 8.

4Tank-In-Tank must be firmly seated to function; remove and reseat Tank-in-Tank.

5Adjust angle; apply more downward pressure.

6Empty Tank-in-Tank, refer page 8

Thank you for selecting a BISSELL product.

If you should happen to need assistance during assembly or operations, call 1-800-237-7691.

Please do not return this product to the store

21

ug310-5861_7950_205.indd 21

3/11/05 8:31:27 AM

Page 20 Page 22
Image 21
Page 20 Page 22
Contents E R ’ S G U I D E ProHeatThanks for buying a Bissell ProHeat Self Propelled Important Safety Instructions Power Cord Powerdrive Knob Will not allow it to exceed Special Features of your Bissell ProHeat Self PropelledDirtLifter PowerBrush SmartMixSmartMix Tank Dial When It’s Time to Empty Tank-in-Tank Tank-in-TankUses to keep the Belts running free ReadyTools Dial Flow IndicatorFloor Cleaning Before You Clean CarpetsOperation Machine PreparationCleaning Fluid Section Use one of the following methods to Preclean the stain Be sure to pre-test any spot removal solutions or chemicalsArea with a clean, damp, color safe cloth Stain RemovalWhen You’re Done AssemblyTurboBrush UseScotchgard protector Applicator Optional How to Clean Upholstery and Small Areas Cleaning TechniqueImportant Check Upholstery Tags Cleaning Tool Trigger. Caution Do not over wet Maintenance/Storage Locate and remove broken pump belt Pump Belt and Brush Belt ReplacementSmartMix Tank and belt access door To Install the Replacement Pump BeltAssembly is now complete Services atPowerdrive is in the OFF position TroubleshootingTurn on the SmartTemp Switch Clean out Flow Indicator Filter,Re-install lid refer to Set to proper setting Set to tool settingBrush Belt or Pump Belt is off or broken Turn the machine OFF and unplug fromAm 10 pm ET Bissell Consumer ServicesReplacement Parts Bissell ProHeat 015-06210730 Limited Two Year Warranty About Your Warranty
Related manuals
Manual 24 pages 10.43 Kb
Top Page Image Contents