Billy Goat VQ902SPH owner manual Assembly, Tighten jam nuts

Page 9

VQ Owner’s Manual

ASSEMBLY

1. UPPER HANDLE (item 41). Assemble securely to lower handle stubs (item 37) and handle brace (item 36), using screws (item 120 & 121), so that screw heads are on inside of handle. Otherwise, premature bag wear could result.

2. NOZZLE DOOR CONTROLS. Assemble ball joints (item 73), jam nuts (item 138), to both ends of rod (item 47). Do not fully

tighten jam nuts.

Using screw (item 113), washer (item 143) and lock nut (item 131), connect one end of rod (item 47) to nozzle door mounting. (See Figure 5). Using rod, pull nozzle door open horizontal to ground and hold opposite end of rod next to mounting hole on remote lever (item 48), already assembled onto upper handle. (See Figure 1). If necessary, adjust rod length using threads provided on rod. Adjust rod length to give a minimum of 1.0" (25.4 mm) hand clearance between lever & maximum forward throttle position when door is open. Assemble upper end of rod to lever on handle using same hardware item numbers as shown above. (See figure 1& 2). Tighten jam nuts.

3. EXHAUST ASSY. Place flange gasket (item 35) onto housing of main unit and assemble exhaust elbow to housing using screws (item 117), washers (item 140) and lock nuts (item 132), provided in parts bag. The rear hole mounts deflector (item 118), using screw assembly (already attached to deflector) and lock nut (item 132). Bend opposite end of deflector down until notch in rear of deflector catches onto handle brace (item 36) (see figure 3).

4. DEBRIS BAG (Item 50) (see figure 4).

4.1Unfold and place mouth of bag over exhaust elbow, completely covering the discharge opening with bag neck straps, placing one on each side of elbow flange.

COMPLETELY TIGHTEN BAG NECK STRAPS

4.2Attach rear hanger straps of bag to the hanger loops located one on each side of the upper handle.

5. CABLES AND WIRES. Attach to the handle using cable clamps (item 44).

6.Secure engine starter rope into starter rope guide (Item 177) using hardware that is preassembled to the lower handle.

7.INSPECT ALL PARTS & MECHANICAL FASTENERS for security and integrity.

8.Note: See debris bag conditioning under operation section on page 11).

SELF PROPELLED ONLY (before starting unit).

9. CONTROL ASSY (item 77).

Before starting engine, check for neutral by placing the control into neutral and engaging the bail, the unit has been adjusted at the factory and should free wheel. If not, adjust as needed by placing the control (item 77) and transmission offset link (item 68) into neutral and adjust nuts on control cable (item 75).

10.Check tire pressure and lubricate all grease and oil points (see MAINTENANCE).

11.Connect spark plug wire.

48

73

138

47

Fig. 1

47

138

73

Fig. 2

118

Deflector notch

36

Fig. 3

Fig. 4

50

Fig. 5

Part No 830542

9

Form No F071307A

Page 8 Page 10
Image 9
Page 8 Page 10
Contents Billy Goat VQ Vacuum About this Manual ContentsVQ902SPH Serial Plate DataGeneral Safety Instructions and Symbols Form No F071307A Sound Vibration DataIntended USE Engine Labels Instruction LabelsPUT OIL in Engine Before Starting Packing ChecklistTighten jam nuts AssemblyStarting OperationDrive Gear selection @ 3400 RPM Periodic Maintenance MaintenanceDrive MaintenanceWarranty Claim Procedure TroubleshootingMaintenance Record Parts Drawing VQ Form No F071307A CAP Tube Parts ListDescr Iptio N Label Speed Control Switch and Wire Assembly Parts List

VQ902SPH specifications

The Billy Goat VQ902SPH is a robust and versatile vacuum system designed to tackle the toughest outdoor cleanup tasks. This powerful machine is a favorite among landscape professionals and homeowners alike, thanks to its high-performance capabilities and user-friendly features.

One of the standout features of the VQ902SPH is its powerful 10.0 HP Honda engine. Known for its reliability and efficiency, this engine provides the suction strength needed to collect debris, leaves, and even small branches with ease. The vacuum boasts an impressive airflow capacity of up to 2000 CFM (cubic feet per minute), making it one of the most effective yard vacuums on the market.

The vacuum is designed with a high-dump feature that allows for easy disposal of collected debris. With a simple pull of a lever, users can dump the contents of the hopper up to 34 inches high, enabling them to empty the vacuum into trash bins or dump trucks without straining their backs. The large 37-gallon collection bag minimizes downtime by allowing for extended use between emptying.

Another notable characteristic of the Billy Goat VQ902SPH is its self-propelled system, which enhances maneuverability. Users can adjust the speed of the machine according to the terrain and their walking pace. This feature is particularly beneficial in larger yards or commercial properties where speed and efficiency are vital.

In terms of technology, the VQ902SPH incorporates a patented design that includes a unique fan system which reduces noise while maximizing suction power. This design minimizes disruption in residential areas while effectively collecting yard debris. The vacuum also features a user-friendly control panel that is easy to operate, even for those who may not be tech-savvy.

Durability is a key aspect of the VQ902SPH’s design. Constructed with heavy-duty materials, it is built to withstand the rigors of frequent use in various weather and soil conditions. The vacuum is equipped with large, pneumatic wheels that provide excellent traction and stability, allowing it to traverse different terrains without difficulty.

Overall, the Billy Goat VQ902SPH is a top-tier choice for anyone in need of a reliable yard vacuum. With its powerful engine, high-dump capability, self-propelled features, and durable construction, it is designed to make outdoor cleanup easier, faster, and more efficient. Whether you are maintaining a residential lawn or managing large commercial properties, the VQ902SPH delivers exceptional performance and convenience.
Top Page Image Contents