Enerco HST45 owner manual MHT / HST Heater Assembly Instructions

Page 11

MHT / HST HEATER ASSEMBLY INSTRUCTIONS

1.Place gaskets from Gasket kit (02885) on each side of the burner box. Use the four mounting studs around each of the three-inch holes for location.

2.Slide the tube flanges over the studs as was done in the prior step with the gaskets. The tube ends extend through the flanges to help with alignment.

3.Using the four long and four short nuts from the bolt kit (02876) secure the tube set to the burner box. As shown in the diagram, use the four long nuts in the center and the four short nuts on the outside.

4.Slide the bulkhead and reflector assembly forward until it stops on the long nuts. Using the (4) 5/16-18 X 1/2" long screws form the (02876) bolt kit secure the bulkhead to the burner box.

USE CAUTION AS NOT TO OVERTIGHTEN ASSEMBLY AS IT MAY CAUSE DAMAGE TO PARTS OF ASSEMBLY

Enerco Group, Inc., Gas-Fired Low-Intensity Infrared Heater 11

Operating Instructions and Owner’s Manual

Image 11

Contents MR. Heater Contents Introduction Available AccessoriesBefore YOU Begin Unpacking the HeaterRear View About The HeaterSide View End View Technical SpecificationsHeater Specifications Venting SpecificationsGas Service Requirements System Requirements Where can the heater be installed?Where can’t the heater be installed? Installer’s responsibilityVenting Requirements Electrical Service Requirements System RequirementsNon-residential Installations GroundingInstallation Materials InstallationSafety Equipment Installation ToolsMinimum Required Safe Distances from Combustibles Horizontal InstallationsTilted Installations General Guidelines ResidentialHeater Orientation Horizontal InstallationTilted Installation Hang the HeaterMHT / HST Heater Assembly Instructions Venting Typical InstallationCanadian Installations1 US Installations2 10 ft Basic Flue Venting Residential OnlyVertical Through the Roof Horizontal Through the Sidewall Venting/DuctingRoof Pitch Double Wall Vertical VentingSingle Wall Single wall vent run Single wall terminal endDirect Outside Air For Combustion Residential Electrical Service InstallationAir For Combustion Residential Outside Combustion Air Supply120V-60Hz Supply Circuit Gas Service InstallationInstall Gas Supply Lines Heater OperationUse LP-resistant joint compound on all threads Proper Operating Flame Maintenance Pre-Season MaintenanceOperation of the Heater Igniter does not Spark TroubleshootingReplace fuse or reset circuit breaker Replace blower motor Blower does not Come onBurner does not Stay LIT Burner does not LightMHT-45 HST-45 Illustrated PartsIllustrated Parts MHT /HST45 Tube Heater Operating Instructions

HST45 specifications

The Enerco HST45 is a high-efficiency heating solution that has gained popularity among consumers looking for effective solutions for their heating needs. This advanced heating system combines innovative technologies and user-friendly features to deliver optimal performance while ensuring energy savings.

One of the standout characteristics of the Enerco HST45 is its robust heating capacity. With the ability to deliver up to 45,000 BTUs, it is designed to effectively heat large spaces, making it an ideal choice for commercial applications and residential use. The unit operates on a propane or natural gas fuel system, providing flexibility in fuel choice based on user availability and preference.

The HST45 is equipped with a cutting-edge infrared heating technology. This system works by directly heating objects and surfaces in a room rather than just circulating warm air. This method results in faster and more efficient heating, reducing energy consumption and providing comfortable warmth even in large or poorly insulated spaces.

Another key feature of the Enerco HST45 is its portability. Designed with ease of movement in mind, it comes with sturdy wheels, allowing users to conveniently transport it to different locations as needed. This makes it a versatile option for construction sites, garages, workshops, and outdoor events.

Safety is also a primary consideration in the design of the HST45. The unit is equipped with an automatic shut-off feature that activates in the event of overheating, ensuring the safety of users and surroundings. Additionally, it includes a protective grill to prevent accidental contact with the heating elements, further enhancing user safety.

User-friendly controls contribute to the overall appeal of the Enerco HST45. The system features easy-to-read gauges and straightforward controls that enable users to adjust the temperature and settings according to their preferences without hassle.

Moreover, the HST45 is designed for durability and longevity, made from high-quality materials that can withstand various environmental conditions. Its sturdy construction helps ensure reliable performance through years of use, making it a worthwhile investment for anyone in need of a dependable heating solution.

In summary, the Enerco HST45 combines powerful heating capabilities, innovative infrared technology, portability, and user safety features, making it an exceptional choice for those seeking effective heating solutions. Its durability and efficiency further enhance its appeal, positioning it as a leader in portable heating systems. As energy efficiency and versatility become increasingly paramount, the Enerco HST45 stands out as a reliable and effective heating option for various applications.