Enerco HST45 Gas Service Installation, Install Gas Supply Lines, 120V-60Hz Supply Circuit

Page 17
heater
Low Voltage
Thermostat Stock # 10367
Low Voltage Thermostat Wiring Diagram
Heaters are normally controlled by thermostat. The recommended 24V thermostat, connects to the unit as shown
in the diagram below.Heater (maximum 1-per thermostat)

CAUTION Label all wires prior to disconnection when servicing controls. wiring errors can cause improper and dangerous operation. Verify proper operation after servicing.

Grounding

120V-60Hz Supply Circuit

The heater must be electrically grounded in accordance with the following codes: United States: Refer to National Electrical Code, ANSI/NFPA-70 – latest revision. Wiring must conform to the most current National Electrical Code and local ordinances. Canada: Refer to Canadian Electrical Code, CSA C22.1 Part 1– latest revision.

WARNING Electrical Shock Hazard

Plug heater into grounded three prong ceiling receptacle. Do not cut or remove the grounding prong from this plug. Do not use with an extension cord. Failure to follow these instructions will result in death or electrical shock.

ATTENTION Risque d’électrocution

Brancher le cordon du radiateur sur un socle à 3 broches et à la masse, situé au plafond. Ne pas sectionner ou retirer la broche de masse de cette prise. N’utilliser aucun cable de rallonge. Le non-respect de ces consignes peut entrainer mort ou electrocution.

The appliance, when installed, must be electrically grounded in accordance with local code, or in the absence of local codes, with the National Electrical Code (ANSI/NFPA 70) or Canadian Electrical Code (CSA 22.1) , if an external electrical source is utilized.

Gas Service Installation

Install Gas Supply Lines

A ½” gas supply connection is required as shown below. To check system pressure, a plugged 1/8” NPT tapping is required upstream of the manual gas shut-off valve supplied with the heater.

Before connecting the heater to the supply system, verify that all high pressure testing of the gas piping has been completed.

DO NOT HIGH PRESSURE TEST THE GAS PIPING WITH THE BURNER CONNECTED.

Follow these instructions to ensure a safe gas supply system installation:

1.Support all gas piping with suitable pipe hanging materials.

2.Use wrought iron or wrought steel pipe and malleable iron fittings. The use of copper tube and brass fittings is acceptable

Enerco Group, Inc., Gas-Fired Low-Intensity Infrared Heater 17

Operating Instructions and Owner’s Manual

Page 16 Page 18
Image 17
Page 16 Page 18
Contents MR. Heater Contents Before YOU Begin Available AccessoriesUnpacking the Heater IntroductionRear View About The HeaterHeater Specifications Technical SpecificationsVenting Specifications Side View End ViewWhere can’t the heater be installed? Where can the heater be installed?Installer’s responsibility Gas Service Requirements System RequirementsNon-residential Installations Electrical Service Requirements System RequirementsGrounding Venting RequirementsSafety Equipment InstallationInstallation Tools Installation MaterialsTilted Installations Horizontal InstallationsGeneral Guidelines Residential Minimum Required Safe Distances from CombustiblesTilted Installation Horizontal InstallationHang the Heater Heater OrientationMHT / HST Heater Assembly Instructions Venting Typical InstallationCanadian Installations1 US Installations2 10 ft Basic Flue Venting Residential OnlyVertical Through the Roof Horizontal Through the Sidewall Venting/DuctingRoof Pitch Single Wall Vertical VentingSingle wall vent run Single wall terminal end Double WallAir For Combustion Residential Electrical Service InstallationOutside Combustion Air Supply Direct Outside Air For Combustion Residential120V-60Hz Supply Circuit Gas Service InstallationInstall Gas Supply Lines Heater OperationUse LP-resistant joint compound on all threads Proper Operating Flame Maintenance Pre-Season MaintenanceOperation of the Heater Replace fuse or reset circuit breaker Replace blower motor TroubleshootingBlower does not Come on Igniter does not SparkBurner does not Stay LIT Burner does not LightMHT-45 HST-45 Illustrated PartsIllustrated Parts MHT /HST45 Tube Heater Operating Instructions

HST45 specifications

The Enerco HST45 is a high-efficiency heating solution that has gained popularity among consumers looking for effective solutions for their heating needs. This advanced heating system combines innovative technologies and user-friendly features to deliver optimal performance while ensuring energy savings.

One of the standout characteristics of the Enerco HST45 is its robust heating capacity. With the ability to deliver up to 45,000 BTUs, it is designed to effectively heat large spaces, making it an ideal choice for commercial applications and residential use. The unit operates on a propane or natural gas fuel system, providing flexibility in fuel choice based on user availability and preference.

The HST45 is equipped with a cutting-edge infrared heating technology. This system works by directly heating objects and surfaces in a room rather than just circulating warm air. This method results in faster and more efficient heating, reducing energy consumption and providing comfortable warmth even in large or poorly insulated spaces.

Another key feature of the Enerco HST45 is its portability. Designed with ease of movement in mind, it comes with sturdy wheels, allowing users to conveniently transport it to different locations as needed. This makes it a versatile option for construction sites, garages, workshops, and outdoor events.

Safety is also a primary consideration in the design of the HST45. The unit is equipped with an automatic shut-off feature that activates in the event of overheating, ensuring the safety of users and surroundings. Additionally, it includes a protective grill to prevent accidental contact with the heating elements, further enhancing user safety.

User-friendly controls contribute to the overall appeal of the Enerco HST45. The system features easy-to-read gauges and straightforward controls that enable users to adjust the temperature and settings according to their preferences without hassle.

Moreover, the HST45 is designed for durability and longevity, made from high-quality materials that can withstand various environmental conditions. Its sturdy construction helps ensure reliable performance through years of use, making it a worthwhile investment for anyone in need of a dependable heating solution.

In summary, the Enerco HST45 combines powerful heating capabilities, innovative infrared technology, portability, and user safety features, making it an exceptional choice for those seeking effective heating solutions. Its durability and efficiency further enhance its appeal, positioning it as a leader in portable heating systems. As energy efficiency and versatility become increasingly paramount, the Enerco HST45 stands out as a reliable and effective heating option for various applications.
Top Page Image Contents