Cadet CBC103TW Operation & Maintenance, How do I insert the heater assembly into the wall can?

Page 4

Installation Instructions

Warranty is void if any material is sprayed on the element or blower.

How do I insert the heater assembly into the wall can?

STEP 3 Install Heater Assembly

Turn heater assembly upside down (element down with motor facing you). Connect the supply wires to the heater wires with connectors (See Figure 9). Now rotate the heater so the element and the fan are facing you. The element should be at the top.

Insert the bottom edge of the heater assembly into the half round slots in the bottom lip of the wall can (See Figure 10). [IMPORTANT: Push wires into bottom of wall can during insertion. Be sure that supply wires are not caught between motor and wall can, attach assembly at top with screw provided.]

Figure 9

STEP 4 Install Grill

Secure grill with the screws provided. Slide thermostat knob onto right control shaft extending through the grill and the timer knob onto the left shaft. Turn power on at the electrical panel board.

Figure 10

Operation & Maintenance

How to operate your heater

1.Once installation is complete and power has been restored, turn the thermostat knob fully clockwise. (The thermostat is on the right.)

2.When the room reaches your comfort level, turn the thermostat knob counterclockwise until the heater turns off. The heater will automatically cycle around this preset temperature.*

3.To reduce the room temperature, turn the knob counterclockwise. To increase the room temperature, turn the knob clockwise.

4.For additional heat beyond thermostat setting, when room is

occupied, turn timer to desired minutes. (The timer is on the left and represented by the symbol . The numbers indicate minutes.) Heater will remain on until time expires, then control of the heater will return to the thermostat and the previous set-point setting.

Maintenance

As needed, or every six months minimum.

1. WARNING! Before removing grill, turn the electrical power off at the electrical panel board (circuit breaker or fuse box). Lock or tag the panel board door to prevent someone from accidentally turning the power on while you are working on the heater. Failure to do so could result in serious electrical shock, burns, or possible death.

2.It is important that you verify power has been turned off and no power is going to the heater before proceeding. Circuit breakers are often not marked correctly and turning the wrong breaker off could mean electricity is flowing to the heater, even if the heater does not appear to be working. If you are uncomfortable working with electrical appliances, unable to follow these guidelines, or do not have the necessary equipment, consult a qualified electrician.

3.Once you verify the power has been turned off correctly, proceed to the next step.

4.Remove screws and take off grill.

5.Wash grill with hot soapy water and dry immediately.

6.While holding fan (to avoid damage or bending), use a hair dryer or vacuum on blow cycle to blow debris through the top element (do not touch element).

7.Vacuum fan area without touching the elements.

8.Replace grill and secure w ith screws.

9.Turn thermostat to desired setting.

10.Turn power back on at the electrical panel board.

About the Manual Reset Temperature Limit Control

The heater is protected by a temperature-limiting control. The manual reset temperature limit control is designed to open the heater circuit when excessive operating temperatures are detected. The problem must be assessed and the limit must be reset to re sume operation.

Resetting the Manual Reset Temperature Limit Control

If the manual reset limit control has opened the heater circuit due to excessive operating temperatures, the heater will not work until the manual reset limit button is pressed. After allowing the unit to cool for at least 10 minutes and resolving the problem causing the limit to trip; use a narrow object such as a ball-point pen to a ccess the manual reset button through the lower-right center section of the heater grill. Press FIRMLY and be sure to listen and feel for a click, indicating it has been reset.

*Note: If thermostat knob is turned fully counterclockwise, it will be in the

4disabled (no heat) position.

Page 3 Page 5
Image 4
Page 3 Page 5
Contents Read all instructions before using this heater Com-Pak Bath HeaterInstallation Instructions How do I install for new construction?Correct 120 Volt Configuration Part TwoDetermine Supply Voltage Select Proper Heater VoltageOperation & Maintenance How do I insert the heater assembly into the wall can?Install Heater Assembly Install GrillTroubleshooting Chart WarrantyLea todas las etiquetas que contengan información Garantía extendida de tres años para el elemento y el motorNo lo instale donde el calentador se pueda mojar Instrucciones para la instalación Parte Uno¿Cómo se instala el calentador En una construcción nueva? En una pared existente?Configuración Correcta DE 240 Voltios Parte DosPaso 1 Determine el voltaje del suministro Paso 2 Seleccione el voltaje adecuado del calentadorFuncionamiento y mantenimiento Paso 3 Instale la unidad del calentadorPaso 4 Instale la rejilla Cómo hacer funcionar el calentadorTabla de resolución de problemas GarantíaBlank

CB103T, CBC103TW specifications

The Cadet CBC103TW and CB103T are innovative smart thermostats designed to provide optimal comfort and energy efficiency in modern homes. These devices stand out in the smart thermostat market due to their advanced features, user-friendly interface, and compatibility with various home automation systems.

One of the main features of the Cadet CBC103TW and CB103T is their sleek, modern design, which allows them to blend seamlessly into any home decor. The intuitive touchscreen display provides users with real-time information on temperature settings, humidity levels, and system status. The easy-to-navigate menu allows homeowners to effortlessly adjust their heating and cooling preferences according to their comfort levels.

These thermostats utilize advanced technologies such as Wi-Fi connectivity, enabling users to control their home’s temperature remotely through a dedicated smartphone app. This app is compatible with both iOS and Android devices, allowing homeowners to adjust their settings from anywhere, whether they are at work or on vacation. The ability to manage heating and cooling schedules remotely not only enhances convenience but also contributes to energy savings.

Energy efficiency is a significant selling point of the Cadet CBC103TW and CB103T. Both models support programmable scheduling, allowing users to set specific heating and cooling times based on their daily routines. By optimizing temperature settings during peak and off-peak hours, these thermostats help reduce energy consumption and lower utility bills.

Another key characteristic is their compatibility with various HVAC systems, including electric and gas heating, as well as central air conditioning systems. This versatility makes the Cadet thermostats suitable for a wide range of homes and setups.

Moreover, the CBC103TW model features a whisper-quiet operation and a user-friendly installation process, making it an excellent choice for both tech-savvy individuals and those less familiar with smart home devices.

Overall, the Cadet CBC103TW and CB103T stand out for their blend of design, technology, and efficiency. These smart thermostats not only enhance comfort but also promote sustainable living by reducing energy consumption, making them an ideal choice for the modern homeowner.
Top Page Image Contents