Desa VF-18N-MHd Determining fresh-air flow for heater location, Confined and Unconfined Space

Page 6

air for combustion

and ventilation

Continued

Unusually tight construction is defined as construction where:

a.walls and ceilings exposed to the out- side atmosphere have a continuous water vapor retarder with a rating of one perm (6 x 10-11kg per pa-sec-m2) or less with openings gasketed or sealed and

b.weather stripping has been added on openable windows and doors and

c.caulking or sealants are applied to areas such as joints around window and door frames, between sole plates and floors, between wall-ceiling joints, between wall panels, at penetrations for plumbing, electrical and gas lines and at other openings.

If your home meets all of the three criteria above, you must provide additional fresh air. See Ventilation Air From Outdoors, page 7.

If your home does not meet all of the three criteria above, proceed to Determining Fresh-Air Flow For Heater Location.

Confined and Unconfined Space

The National Fuel Gas Code, ANSI Z223.1/NFPA 54 defines a confined space as a space whose volume is less than 50 cubic feet per 1,000 Btu per hour (4.8 m3 per kw) of the aggregate input rating of all appliances installed in that space and an unconfined space as a space whose volume is not less than 50 cubic feet per 1,000 Btu per hour (4.8 m3 per kw) of the aggregate input rating of all appliances installed in that space. Rooms com- municating directly with the space in which the appliances are installed*, through openings not furnished with doors, are considered a part of the unconfined space.

*Adjoining rooms are communicating only if there are doorless passageways or ventilation grills between them.

determining fresh-air flow for heater location

Determining if You Have a Confined or

Unconfined Space

Use this work sheet to determine if you have a confined or unconfined space.

Space: Includes the room in which you will install heater plus any adjoining rooms with doorless pas- sageways or ventilation grills between the rooms.

1.Determine the volume of the space (length x width x height).

Length x Width x Height =__________cu. ft. (volume of space)

Example: Space size 20 ft. (length) x 16 ft. (width) x 8 ft. (ceiling height) = 2,560 cu. ft. (volume of space)

If additional ventilation to adjoining room is supplied with grills or openings, add the volume of these rooms to the total volume of the space.

2.Multiply the space volume by 20 to determine the maximum Btu/Hr the space can support.

___________ (volume of space) x 20 = (Maxi- mum Btu/Hr the space can support)

Example: 2,560 cu. ft. (volume of space) x 20 = 51,200 (maximum Btu/Hr the space can support)

3.Add the Btu/Hr of all fuel burning appliances in the space.

Vent-free fireplace

____________Btu/Hr

Gas water heater*

____________Btu/Hr

Gas furnace

____________Btu/Hr

Vented gas heater

____________Btu/Hr

Gas fireplace logs

____________Btu/Hr

Other gas appliances*

+____________Btu/Hr

Total

=____________Btu/Hr

*Do not include direct-vent gas appliances. Di- rect-vent draws combustion air from the outdoors and vents to the outdoors.

Example:

 

40,000

 

Gas water heater

 

Btu/Hr

Vent-free fireplace

+

33,000

Btu/Hr

Total

=

73,000

Btu/Hr

4.Compare the maximum Btu/Hr the space can support with the actual amount of Btu/Hr used.

__________ Btu/Hr (maximum the space can support)

__________ Btu/Hr (actual amount of Btu/Hr used) Example: 51,200 Btu/Hr (maximum the space

can support)

73,000 Btu/Hr (actual amount of Btu/Hr used)

The space in the example is a confined space because the actual Btu/Hr used is more than the maximum Btu/Hr the space can support. You must provide ad- ditional fresh air. Your options are as follows:

A.Rework worksheet, adding the space of an adjoin- ing room. If the extra space provides an unconfined space, remove door to adjoining room or add ventilation grills between rooms. See Ventilation Air From Inside Building, page 7.

B.Vent room directly to the outdoors. See Ventila- tion Air From Outdoors, page 7.

C.Install a lower Btu/Hr fireplace, if lower Btu/Hr size makes room unconfined.

www.desatech.com116986-01B

Image 6
Contents What to do if YOU Smell GAS Models VF-18N-MHD, VF-18P-MHD, VF-24N-MHD VF-24P-MHDTable of Contents Safety Information Product Identification Product IdentificationUnpacking Product FeaturesLocal Codes Air For Combustion VentilationDetermining fresh-air flow for heater location Confined and Unconfined SpaceDetermining if You Have a Confined or Unconfined Space Ventilation AIR Ventilation Air From Inside BuildingVentilation Air From Outdoors Installation Check GAS TypeInstallation and clearances for vent-free operation Installation Mantel Clearances Installing Heater AssemblyDetermining Minimum Mantel Clearance When using a Hood Floor ClearancesConnecting to gas supply Installation Items NeededChecking gas connections Natural GasPropane/LP Gas Pressure Testing Heater Gas Connections Adding Embers, Lava rock and Decorative logsTest Pressures Equal To or Less Than Psig 3.5 kPa For your safety Read before lighting Operating HeaterRemote Control FunctionsProcedure Manual LightingPilot Flame Pattern Inspecting BurnersTo turn gas off To appliance Lighting with Piezo IgnitorCleaning Maintenance Burner Flame PatternBurner Injector Holder Air Inlet Hole Injector Holder on Front Burner Tube Troubleshooting Observed Problem Possible Cause RemedySee Cleaning and Mainte Bad module Replace module Gas leak. See WarningWiring Diagram Identifying error signals from receiverTechnical Service Replacement PartsService Hints AccessoriesIllustrated Parts Breakdown Models VF-18N-MHD, VF-18P-MHD, VF-24N-MHD and VF-24P-MHDParts List Warranty Information Keep this WarrantyLimited Warranty VENT-FREE GAS LOG Heaters