Bradford-White Corp IGE-199C Series, IGE-199R Series Unpacking, Water Heater Location

Page 9

WARNING

•This water heater is suitable for potable water heating only. DO NOT use this water heater for space heating or combination space heating/domestic water heating.

•This water heater is not suitable for use in pool or spa applications.

•The water heater must be installed outdoors. Failure to properly install this water heater outdoors may result in property damage, personal injury, or death. Refer to the installation of the water heater in this installation and instruction manual for details on the location and installation outdoors. DO NOT INSTALL INDOORS.

WARNING

Pressure relief valve discharge piping must be piped near the ground or drain to eliminate potential of severe burns. Insulate and use electrical heat tape around the discharge drain pipe in any area where freezing could occur. Do not install any shut-off valves, plugs or caps to the pressure relief valve or discharge piping.

CAUTION

If building cold water supply has a back-flow preventer, check valve or water meter with check valve, provisions for thermal expansion of water in the hot water system must be provided.

DANGER

Temperature setting should not exceed safe temperature at fixtures. See water temperature control warnings in the “Temperature Adjustment Section” of this Installation and Operating Instruction Manual. If higher preheat temperatures are necessary to obtain adequate booster output, add an ASSE approved mixing valve for hot water supplied to fixtures.

UNPACKING

INSPECT SHIPMENT carefully for any signs of damage.

1.All equipment is carefully manufactured, inspected and packed.

2.Any claims for damage or shortage in shipment must be filed immediately with Bradford White Corporation and noted on the Bill of Lading.

WATER HEATER LOCATION:

1.The IGE series water heaters must be installed outdoors. Refer to figure 1 and table 1 (Section IV) in this Installation and Instruction Manual for minimum installation clearances before choosing a final location for the water heater.

2.The water heater must be installed on a wall capable of supporting at least 50 pounds (23 Kg). Locate the water heater at a height convenient for servicing and above the reach of small children.

3.Minimum clearance to combustible material is 12” (30.5 cm) from the Top, 24” (61 cm) from the Front, 0” from the Rear, 6” (15.2 cm) from the Sides, and 12” (30.5 cm) from the Bottom of this water heater. An optional recess box is available for installing the water heater recessed in an outside wall and enclosing the piping (see features section). When the water heater is installed in a recess box, the clearances from the top, bottom, sides, and back surfaces of the recess box to combustible materials are 0”. The clearance from combustibles from the front of the recess box is 24” (61 cm). Contact your Bradford White distributor for information on obtaining and installing the water heater in a recess box.

9

Page 8 Page 10
Image 9
Page 8 Page 10
Contents IGE-199R and IGE-199C Model Series Table of Contents Page Do not Operate the Appliance Until the Leakage is Corrected IGE-199R-10X Section II SpecificationsEVERHOT→ IGE Model Series Dimensions Section III General Information FeaturesDo not Operate the Appliance Until the Leakage is Corrected Section IV Installation InstructionsWater Heater Location UnpackingReference Description Minimum Distance Inches cm Build Opening Clearances FigRemove Carton Mount Water Heater on the WallSection V Water Connections Lime Condition Warning SignalWater Quality Instructions for ConnectionsPage Recommended Piping for a Basic Installation Drain Solenoid Piping Fig Recommended Piping for Power Failure Freeze ProtectionRecommended Piping for a Circulation System Page Pressure Relief Valve Section VI GAS Connections Never USE a Match or Open Flame for TestingInitial Operation and Testing Installer only GAS Meter Size -NATURALGAS onlyGAS Pressure Regulation Page Section VII Electrical Connections Wiring Diagram Wiring Diagram Schematic Residential Models Remote Temperature ControlsEndless hot water system Commercial Models Initial Operation and Testing of Controls Installer only Control Wiring Connections Inside Water HeaterSection Viii Operating Instructions To Fill the Water HeaterSequence of Operation Manual Gas Valve Fig To Turn OFF GAS to the ApplianceResidential Models see Figure Turning OFF the Water Heater for AN Extended Period of TimeControl For Residential Models Fig Control for Commercial Models Fig Commercial Models see FigureScalding Approximate TIME/TEMPERATURE Relationships in Scalds Error Messages on Remote Temperature Control DisplayFirst AID for Scalds Burner Flame Appearance Fig Section IX MaintenancePage Lime Scale Flushing Diagram Fig Schematic Diagram of Internal Parts Section X Parts List Internal Components Internal Components Electrical Components Parts List Anti-Frost Heater Clip

IGE-199R Series, IGE-199C Series specifications

Bradford-White Corporation is a renowned manufacturer in the water heating industry, providing high-quality solutions for residential and commercial applications. Among its innovative line of products, the IGE-199R and IGE-199C Series stand out for their exceptional performance and efficiency in delivering hot water.

The IGE-199R and IGE-199C Series are powered by advanced technology designed to meet the demands of both modern homes and commercial settings. They feature advanced tankless water heating systems that offer continuous hot water on demand, eliminating the need for bulky storage tanks. This not only saves space but also enhances energy efficiency, as hot water is produced only when needed.

One of the key features of the IGE-199R and IGE-199C is their Energy Star certification, attesting to their high efficiency. These units utilize a powerful, high-efficiency condensing heat exchanger, which maximizes heat transfer while minimizing energy loss. The design facilitates a uniform and solid flow rate, ensuring that multiple outlets can be served simultaneously without compromising performance.

Both series also incorporate cutting-edge technology, such as modulating gas burners that adjust the heat output to match the hot water demand. This means that these units can efficiently operate at varying levels of energy consumption, ultimately resulting in lower utility bills for the consumer. Additionally, the units are equipped with an integrated control system that monitors system performance and provides digital diagnostics, making maintenance and troubleshooting straightforward.

Safety features are also paramount in the design of the IGE-199R and IGE-199C models. The units are outfitted with a range of safety sensors, including temperature and pressure relief valves, ensuring safe operation and preventing potential hazards. Furthermore, the innovative venting options allow for flexible installation, even in tight spaces, without compromising safety or efficiency.

The IGE-199R and IGE-199C Series are engineered to be user-friendly, offering a clear interface for easy operation and monitoring. Their robust construction ensures durability and reliability, making them an excellent choice for long-term investment in hot water solutions.

In summary, Bradford-White's IGE-199R and IGE-199C Series deliver exceptional quality and performance in tankless water heating. With their focus on energy efficiency, advanced technologies, and safety features, these units provide a reliable and effective solution for meeting the hot water needs of any household or commercial space.
Top Page Image Contents