A.O. Smith GDVT Standard Vent Arrangement, Vent Assembly, Uncompressing the Corrugated Tubing

Page 17

STANDARD VENT ARRANGEMENT

3.6 in.

 

 

17 in. (432mm) MIN.,*

 

 

(91mm)

 

2.6 in.

80 in. (2.03m) MAX.

WALL

 

 

 

(67mm)

 

 

 

 

 

 

 

 

 

 

2.1 in. (54.5mm)

FIGURE 17

*If the horizontal distance is less than 30 in. (760mm), the restricter plate must be installed (see Figure 22).

VENT ASSEMBLY

The vent tube and terminal are assembled by the manufacturer as shown in Figure 18. There are springs fastened inside the corrugated tube. When the vent tubes are pulled to a required length, the distances between the springs will still be equally spaced.

SPRINGCLAMP

FIGURE 18

SECURING VENT TERMINATION ASSEMBLY TO THE EXTERIOR WALL.

Insert the 6 in. (52mm) tube through the clearance hole from exterior wall then secure the vent terminal to the exterior wall with 4 screw anchors (not included) appropriate for the type of wall construction. Caulk the junction of the vent terminal base plate and the exterior wall with exterior type sealant (not included).

SEALANT

FIGURE 19

UNCOMPRESSING THE CORRUGATED TUBING

1.Pull the 3-1/8 in. (80mm) corrugated tube towards the water heater and leave some length over the water heater’s center for bending.

2.Pull the 6 in. (152mm) corrugated tube toward the water heater and leave it 1 in. (25mm) shorter than 3-1/8 in. (80mm) tube.

3.Make sure there are two springs evenly spaced at the bend in the tube.

4.Use metal hangers to keep venting level or with a slope upward from the heater to terminal.

SPRING

REDUCER

H

FIGURE 20

Bend the 3-1/8 in. (80mm) and 6 in. (152mm) corrugated tube all together toward the water heater’s flue connection.

FIGURE 21

VENT RESTRICTER PLATE

For short horizontal vent runs (see Figure 17) place the restricter plate over the flue tube reducer before connecting the 3-1/8 in. (80mm) corrugated tube to the flue tube reducer. DO NOT use the restricter plate if the horizontal run is greater than 30 in. (760mm).

UPPER AIR

RESTRICTER

INLET BOX

PLATE

FLUE TUBE

REDUCER

FIGURE 22

17

Page 16 Page 18
Image 17
Page 16 Page 18
Contents Residential GAS Water Heaters Important Definitions Safe INSTALLATION, USE and ServiceGeneral Safety Introduction Table of ContentsKeep Clear of ALL Obstructions GET to Know Your Water Heater Replacement Parts Typical InstallationHotter Water can Scald Mixing Valve UsageFacts to Consider about the Location Locating the NEW Water HeaterVent Termination Insulation BlanketsVentilation for Appliances Located in Confined Spaces Required Ability Installing the NEW Water HeaterInspect Shipment GeneralValve and Pipe Insulation if Supplied TEMPERATURE-PRESSURE Relief ValveGAS Piping Water Potable Heating and Space HeatingClosed Water System GAS Piping with Flexible Connector Venting High Altitude InstallationsSediment Traps Filling the Water Heater Vent Terminal Clearances Combustion AIR and VentilationHigh Rise Vent Arrangement Vent ConnectionsLocating Clearance Hole for Vent Securing Vent Termination Assembly to the Exterior Wall Vent AssemblyStandard Vent Arrangement Uncompressing the Corrugated TubingMinimum Offset Vent ArrangementFigure D TOP KnobTemperature Regulation Temperature RegulationExternal Damage For Your InformationStart UP Conditions Operational ConditionsAIR in HOT Water Faucets Pilot and Main Burner MaintenanceVenting System Inspection Anode ROD Maintenance Temperature & Pressure Relief ValveDraining Cathodic Protection AnodeDrain Valve Washer Replacement Leakage Checkpoints ServiceProblem Possible Causes Correction Troubleshooting GuidelinesERY Slow HOT Water RecovDrip from Relief Valve Thermostat Fails toPage XCV, XCVL, XCVH, XVR Series Tank PartsXCVT, Xcvx Conditions and ExceptionsClaim Procedure Service and Labor ResponsibilityInstallation Information Limitation on Implied WarrantiesTennessee Waltz Parkway Ashland CITY, TN

GDV, GDVT specifications

A.O. Smith is a well-known name in the water heating industry, and its GDVT and GDV series of water heaters exemplify the company's commitment to quality, efficiency, and innovation. These models are designed to provide reliable hot water solutions for both residential and commercial needs, seamlessly integrating advanced technology and user-friendly features.

One of the main features of the GDVT and GDV series is their high energy efficiency ratings. These water heaters utilize advanced insulation and energy-saving technologies, allowing them to achieve impressive efficiency levels. The GDVT series, for instance, can achieve an Energy Factor (EF) rating of up to 0.96, making it an environmentally friendly choice that can significantly reduce energy bills. This high level of efficiency is a result of thoughtful engineering, including a highly insulated tank that minimizes heat loss.

Another standout characteristic of the GDVT and GDV series is their compact design. These models are built to fit into tight spaces, making them ideal for homes or businesses with limited installation areas. Despite their compact size, they maintain a large storage capacity, ensuring that users have access to consistent hot water. The GDVT series is particularly known for its vertical design, which allows for easy installation in smaller utility rooms or closets.

The GDV models feature a robust digital display that provides real-time information about the water heater's operation. Users can easily monitor the unit’s performance and make adjustments as needed. Additionally, these models come equipped with advanced safety features, including a built-in safety shut-off system and over-temperature protection, ensuring safe and reliable operation.

Both the GDVT and GDV series utilize A.O. Smith's innovative HydroJet® technology, which minimizes sediment buildup within the tank. This technology involves the strategic placement of an internal dip tube that maximizes water circulation, helping to extend the life of the water heater and maintain optimal performance over the years.

In summary, the A.O. Smith GDVT and GDV series water heaters are an excellent choice for those seeking a balance of efficiency, compact design, advanced technology, and enhanced safety. With their impressive energy ratings, user-friendly features, and cutting-edge technologies, these units are tailored to meet the demands of modern residential and commercial water heating solutions, ensuring a consistent supply of hot water while minimizing environmental impact.
Top Page Image Contents