A.O. Smith GDVT Water Potable Heating and Space Heating, Closed Water System, GAS Piping

Page 12

distance below the structural floor. Be certain that no contact is made with any live electrical part. The discharge opening must not be blocked or reduced in size under any circumstances. Excessive length, over 30 ft. (9.14m), or use of more than four elbows can cause restriction and reduce the discharge capacity of the valve, see Figures 5 or 10.

No valve or other obstruction is to be placed between the relief valve and the tank. Do not connect tubing directly to discharge drain unless a 6 in. (152mm) air gap is provided. To prevent bodily injury, hazard to life, or property damage, the relief valve must be allowed to discharge water in quantities should circum- stances demand. If the discharge pipe is not connected to a drain or other suitable means, the water flow may cause property damage.

4.When the system requires water for space heating at temperatures higher than required for domestic water purposes, a tempering valve must be installed, see Figure 7 for suggested piping arrangement.

The Discharge Pipe:

•Shall not be smaller in size than the outlet pipe size of the valve, or have any reducing couplings or other restrictions.

•Shall not be plugged or blocked.

•Shall be of material listed for hot water distribution.

•Shall be installed so as to allow complete drainage of both the temperature-pressure relief valve, and the discharge pipe.

•Shall terminate at an adequate drain.

•Shall not have any valve between the relief valve and tank.

The temperature-pressure relief valve must be manually oper- ated at least once a year. Caution should be taken to ensure that

(1)no one is in front of or around the outlet of the temperature- pressure relief valve discharge line, and (2) the water manually discharged will not cause any bodily injury or property damage because the water may be extremely hot.

If after manually operating the valve, it fails to completely reset and continues to release water, immediately close the cold water inlet to the water heater, follow the draining instructions, and re- place the temperature-pressure relief valve with a new one.

WATER (POTABLE) HEATING AND SPACE HEATING

1.All piping components connected to this unit for space heating applications shall be suitable for use with potable water.

2.Toxic chemicals, such as those used for boiler treatment, shall NEVER be introduced into this system.

3.This unit may NEVER be connected to any existing heating system or component(s) previously used with a non-potable water heating appliance.

FIGURE 7

CLOSED WATER SYSTEM

A closed system will exist if a back-flow preventer (check valve), pressure reducing valve, or other similar device is installed in the cold water line between the water heater and the street main (or well). Excessive pressure may develop due to the thermal expansion of heated water causing premature tank failure or intermittent relief valve operation. This type of failure is not covered by the limited warranty. An expansion tank may be necessary in the cold water supply to alleviate this situation, see Figure 1. Contact the local plumbing authority.

If the temperature and pressure relief valve on the appliance discharges periodically, this may be due to thermal expansion in a closed water supply system. Contact the water supplier or local plumbing inspector on how to correct this situation. DO NOT PLUG THE TEMPERATURE AND PRESSURE RELIEF VALVE.

GAS PIPING

Make sure the gas supplied is the same type listed on the model rating plate. The inlet gas pressure must not exceed 14 inch water column (3.5 kPa) for natural and propane gas (L.P.). The

12

Page 11 Page 13
Image 12
Page 11 Page 13
Contents Residential GAS Water Heaters Safe INSTALLATION, USE and Service Important DefinitionsGeneral Safety Table of Contents IntroductionKeep Clear of ALL Obstructions Typical Installation GET to Know Your Water Heater Replacement PartsMixing Valve Usage Hotter Water can ScaldLocating the NEW Water Heater Facts to Consider about the LocationInsulation Blankets Ventilation for Appliances Located in Confined SpacesVent Termination Installing the NEW Water Heater Required AbilityInspect Shipment GeneralTEMPERATURE-PRESSURE Relief Valve Valve and Pipe Insulation if SuppliedWater Potable Heating and Space Heating Closed Water SystemGAS Piping GAS Piping with Flexible Connector High Altitude Installations Sediment Traps Filling the Water HeaterVenting Combustion AIR and Ventilation Vent Terminal ClearancesVent Connections Locating Clearance Hole for VentHigh Rise Vent Arrangement Vent Assembly Securing Vent Termination Assembly to the Exterior WallStandard Vent Arrangement Uncompressing the Corrugated TubingOffset Vent Arrangement MinimumTOP Knob Figure DTemperature Regulation Temperature RegulationFor Your Information External DamageStart UP Conditions Operational ConditionsAIR in HOT Water Faucets Maintenance Venting System InspectionPilot and Main Burner Temperature & Pressure Relief Valve Anode ROD MaintenanceDraining Cathodic Protection AnodeDrain Valve Washer Replacement Service Leakage CheckpointsTroubleshooting Guidelines Problem Possible Causes CorrectionSlow HOT Water Recov ERYDrip from Relief Valve Thermostat Fails toPage Series Tank Parts XCV, XCVL, XCVH, XVRXCVT, Xcvx Conditions and ExceptionsService and Labor Responsibility Claim ProcedureInstallation Information Limitation on Implied WarrantiesTennessee Waltz Parkway Ashland CITY, TN

GDV, GDVT specifications

A.O. Smith is a well-known name in the water heating industry, and its GDVT and GDV series of water heaters exemplify the company's commitment to quality, efficiency, and innovation. These models are designed to provide reliable hot water solutions for both residential and commercial needs, seamlessly integrating advanced technology and user-friendly features.

One of the main features of the GDVT and GDV series is their high energy efficiency ratings. These water heaters utilize advanced insulation and energy-saving technologies, allowing them to achieve impressive efficiency levels. The GDVT series, for instance, can achieve an Energy Factor (EF) rating of up to 0.96, making it an environmentally friendly choice that can significantly reduce energy bills. This high level of efficiency is a result of thoughtful engineering, including a highly insulated tank that minimizes heat loss.

Another standout characteristic of the GDVT and GDV series is their compact design. These models are built to fit into tight spaces, making them ideal for homes or businesses with limited installation areas. Despite their compact size, they maintain a large storage capacity, ensuring that users have access to consistent hot water. The GDVT series is particularly known for its vertical design, which allows for easy installation in smaller utility rooms or closets.

The GDV models feature a robust digital display that provides real-time information about the water heater's operation. Users can easily monitor the unit’s performance and make adjustments as needed. Additionally, these models come equipped with advanced safety features, including a built-in safety shut-off system and over-temperature protection, ensuring safe and reliable operation.

Both the GDVT and GDV series utilize A.O. Smith's innovative HydroJet® technology, which minimizes sediment buildup within the tank. This technology involves the strategic placement of an internal dip tube that maximizes water circulation, helping to extend the life of the water heater and maintain optimal performance over the years.

In summary, the A.O. Smith GDVT and GDV series water heaters are an excellent choice for those seeking a balance of efficiency, compact design, advanced technology, and enhanced safety. With their impressive energy ratings, user-friendly features, and cutting-edge technologies, these units are tailored to meet the demands of modern residential and commercial water heating solutions, ensuring a consistent supply of hot water while minimizing environmental impact.
Top Page Image Contents