A.O. Smith BFM - 120, BFM - 100 manual Appliances heating cycle Protection for the appliance

Page 13

gis

In this appliance, the cold water enters the bottom of the tank through the cold water inlet (14). The heat of combustion is conducted to the water by the combustion chamber (50) and heat exchanger (11). The heated tap water leaves the tank through the hot water outlet (2). Once the appliance is completely filled with water, it will constantly be under mains water pressure. When hot water is drawn from the appliance, it is immediately replenished with cold water.

The air required for combustion is forced into the combustion chamber by the fan.

The gas required for combustion flows via the gas control (16) in the manifold. The gas control for the BFM 120 is non-standard (see box). Orifices are mounted in the manifold. The gas is injected into the burner bars at pressure from these orifices (36). The burner bars together form the burner tray. The injection of gas into the burner bars also draws in the primary air from the combustion chamber, which is required for combustion. The narrow opening in the orifice causes the gas flow to accelerate. This in turn causes a partial vacuum. It is this partial vacuum that draws in the air (the Venturi effect).

Ignition of the gas/air mixture takes place in two stages. First, the pilot flame is ignited by a spark igniter. This pilot flame then ensures that the complete ignition takes place.

The flue gases released by this combustion are led through the heat exchanger. The heat exchanger is composed of flue tubes that contain flue baffles. These retard the flow of the flue gases, thereby increasing the thermal efficiency of the appliance.

The flue gases are exhausted from the appliance via the top box (46). The top box of the BFM 100 and 120 is non-standard (see box).

An air distribution plate (50) mounted below the burner tray radiation shield also serves as a radiation shield. Any condensation that forms is drained towards the siphon via the air distribution plate.

The PU insulation layer (24) prevents heat loss. The inside of the tank is enamelled to protect against corrosion. The anodes (9) offer extra protection.

2.3The appliance's heating cycle

2.4Protection for the appliance

The entire appliance is controlled by the burner control (40) and the control thermostat (41) or frost thermostat (44). The control thermostat and frost thermostat both independently measure the water temperature (Twater). The appliance's heating cycle is activated as soon as Twater falls below the threshold value (Tset). The value of Tset depends on the selected mode of the appliance (8.2 "Operating modes"). When the appliance is in OFF mode (frost protection), this value is determined by the frost thermostat (threshold value = 20°C). When the appliance is in ’ON mode’, the threshold value can be set via the control thermostat (±40°C - ±70°C).

The instant Twater falls below Tset, the appropriate thermostat (control or frost) will close, and the burner control will identify a heat demand. The gas control will open, and the gas will mix with air. This mixture is ignited by the spark igniter, and the water becomes heated. As soon as Twater rises above Tset, the thermostats will open once more. The heat demand is suspended, and the burner control stops the heating cycle.

The thermostats have a certain margin both when opening and when closing. We refer to this margin as hysteresis. The hysteresis cannot be adjusted.

2.4.1Introduction

The burner control monitors the water temperature by means of thermostats, and ensures that the combustion is safe. This takes place using:

Instruction manual BFM

13

Page 12 Page 14
Image 13
Page 12 Page 14
Contents Page Page Trademarks Read this manual carefullyLiability More informationGis Table of contents Performing maintenance TroubleshootingWarranty certificate Electrical diagramAbout the appliance IntroductionWhat to do if you smell gas Regulations Symbol Target group Maintenance Forms of notation Target groupsIntroduction Document Overview of thisChapter Target groups Description Gis General working Working principle of the appliancePrinciple Appliance Working principle of the appliance Appliances heating cycle Protection for the appliance Pressure switch Water temperature protectionFlame probe Protection DescriptionUnvented installation Safety of the instal- lationVented installation 3 T&P valveGis Air humidity and ambient temperature InstallationAir humidity and ambient temperature PackagingMaximum floor load InstallationWater composition Working clearancesTechnical specifica- tions Plan and elevation of the appliance Dimensions of the applianceDimens Description General and electrical specificationsBFM100 BFM120 Ion UnitDescription Unit Gas dataNatural gas G20 20 mbar LP gas data G30 30 mbar butaneInstallation diagram Installation diagramCold water side Water connections, VentedRecirculation pipe Hot water sideCirculation pipe Water connections, Unvented See C in the installation diagram 3.5 Installation diagramGas connection Circulation pipeAir supply and flue Introduction Installing chimney flue components for BFM 30, 50Subject Description Concentric wall flue terminal BFMConcentric roof flue terminal BFM 30, 50 Installing chimney flue components for BFM 100 C33 concentric roof flue terminal specifications BFM 30, 50Concentric wall flue terminal BFM100 M2000 MDV SCC C13 concentric wall flue terminal specifications BFM 100Concentric roof flue terminal BFM 100 Electrical connection 11 C33 concentric roof flue terminal specifications BFM 100Mains power Fan Alarm Off Connecting the mains powerGas control for BFM 30 through Checking the supply pressure and burner pressureGas control for BFM BFM BFM 30, 50, 80Conversion Conversion to a different gas categoryConversion to a different gas category Orifice replacementPage Conversion to a different gas category Filling Filling Draining Draining Draining unvented installationsDraining vented installations Gis Control panel ON/OFF switchExplanation of icons Control thermostatControl panel Burner control reset buttonStatus of the appliance Error conditionsOperating modes Status of the appliance Starting the appliance Starting and runningAppliances heating cycle Starting and running Shutting down Shutting down the appliance for a brief period OFF modeIsolating the appliance from the mains Shutting the appliance down for a long periodShutting down Control thermostat 7.5 Control thermostat TroubleshootingSymptom Cause Solution Remark Gas smell Troubleshooting general errorsWater leakage Explosive ignitionSymptom Cause Solution Remark Insufficient hot water Troubleshooting insufficient hot waterTroubleshooting No hot water Cycle Symptom Cause Solution RemarkPage Introduction Preparation for maintenance Performing maintenancePerforming maintenance Descaling and cleaning the tankWater-side mainte- nance 12.3.1 Checking the anodesIMD-0235 R2 Clean the orifices Clean the burnersGas-side mainte- nance 12.4.1 Checking the flue baffles Finalising mainte- nance13.1 General warranty Warranty certificate13.2 Tank warranty Conditions for Instal- lation and useWarranty certificate Electrical diagram Electrical diagram BFM Electrical DiagramOptional Components Electrical diagram Index Index 0306
Top Page Image Contents