Genie SC 1200/1500 manual Required Programming, Introduction, Overview of PoWERHEAD Controls

Page 5
3 Required Programming

3 Required Programming

NOTE: Before you begin programming, check to make sure there are no objects in the garage door opening.

INTRODUCTION

Now that your Genie garage door opener is installed, you will want to program the opener so that the door opens and closes properly and all remote devices operate correctly. The following steps guide you through setting your opener so it functions properly for you.

The following information will take you through programming your opener’s functional settings for use.

There are only 2 “required” programming processes you will need to follow to set up your garage door opener for operation:

1.“TRAVEL LIMITS”

2.“REMOTE PROGRAMMING”

Term Definitions:

Travel Limits programming allows you to set how far your door travels up or down in opening and closing your garage door.

Remote Programming synchronizes your remote control devices (remotes, wall console, and keypad) with the powerhead.

Force Control refers to how much power is needed to move (open/ close) your particular door and does NOT require programming.

Speed Control refers to how fast or slow your opener opens and closes your particular door and is preset at the factory. This function does NOT require programming.

Overview of PoWERHEAD Controls

This section describes the programming functions on the powerhead of the opener. Use the following information to familiarize yourself with the buttons, LED indicators and products used to program functions.

Powerhead: There are 3 programming buttons and 2 LED lights on the powerhead. Each of the buttons is used to enter and complete the setup programming. The LED lights indicate status or a function change by illuminating ON, OFF, or ON FLASHING in one of three different colors: blue, red or purple.

There are 4 programs (The 2 “Factory Set” programs are unlikely to need changes.)

1.Door Travel Limits Program

–This program is used to set how far your door travels up and down.

2.Remote Programs (Default menu)

–These show you how to program your remotes to synch with additional remote control devices, wall consoles, keypads, and the powerhead.

3.Door Force Program (Factory Set)

–This program is only used for minor adjustments under certain circumstances.

4.Door Speed Program (Factory Set)

–This program does not require manually initiated changes.

NOTE: The 3 programming buttons are for programming ONLY. These buttons should NOT be used to operate the opener once the Required Programming section has been successfully completed.

ROUND LED

Close Travel

Open Travel

Indicator

Button

PROGRAM

SET – +

LONG LED

Indicator

Located on bottom of Powerhead.

PROGRAM

 

Enters into and selects programming menus.

 

SET

 

Multi-function; move door during programming

–

+ and advance through menus

 

5

G999-393 Manual-ScrewBeltChain-EN indd 5

7/13/12 10 17 AM

Page 4 Page 6
Image 5
Page 4 Page 6
Contents SilentMax 1000/1200, CB 1000/1200, IntelliG 1000/1200 GARAGE DOOR OPENER MODELSHomelink and Car2U compatible OPERATION & MAINTENANCE MANUALTable of Contents Need help or have questions? Call usSAVE THESE INSTRUCTIONS READ AND FOLLOW ALL INSTRUCTIONS IMPORTANT SAFETY INSTRUCTIONS 1 Safety InformationREAD THIS SAFETY INFORMATION OVERVIEW OF POTENTIAL HAZARDSSAFETY FEATURES 2 Featuresopener features INFRARED PROTECTION FUNCTION3 Required Programming Overview of PoWERHEAD ControlsINTRODUCTION Located on bottom of PowerheadClosing Garage Door Down Limits TRAVEL LIMITSround LED remains off will begin flashingRelease up arrow button + and the round LED Opening Garage Door Up Limitswill begin flashing PROGRAMIn your carton you will find one of the following wall consoles Wall Console / OverviewSeries II Wall Consoles with White Buttons Series III Wall Consoles with Black ButtonsContact Reverse Test Contact Reverse AdjustmentForce and Speed Control HOLD 2 seconds REMOTES / New Intellicode 2 Openers15 Release the Program Set button the long LED begins flashing purple Repeat as necessary for additional Remotes The Remote button is now programmedEach Remote can be programmed for three door openers BASIC PROGRAMMING IS COMPLETE AND YOUR GARAGE DOOR IS READY TO USEResetting PIN Setting Up a PINPROGAMMING THE WIRELESS KEYPAD 4 Optional Programming2 seconds Clearing Memory FOR RemoTESHOLD Red = Intellicode 1 Green = Intellicode INTELLICODE 1 REMOTESPress and release the Remote button 3 times on your older Genie door openerAttaching door braCket tO door 5 One-Piece DoorsAttaching door arm tO door braCket Door centerlineREGULAR MAINTENANCE Maintenance and AdjustmentsSAVE THESE INSTRUCTIONS Important Safety InstructionsREGULAR MAINTENANCE continued 6 Maintenance and AdjustmentsCORRECTIVE MAINTENANCE Screw DriveBLUE then OFF FORCE Settings are resetDOWN FORCE Locating Safe-T-Beam Pairs Adjustment Guides continuedOne Door Garage Three Door GaragePOWER CORD 7 Wiring DiagramOPENING COVER MAY CAUSE ELECTRIC SHOCK ELECTRICAL SHOCKOPERATION TroubleshootingPOWERHEAD LEDS 8 TroubleshootingPowerMax 1200/1500, SC 1200/1500, TriloG 1200/1500, PowerLift 9 WarrantyGPower 900, SilentMax 1000/1200, CB 1000/1200, IntelliG 1000/1200 LIMITED WARRANTYEasy operation at your finger tips Genie-Net technology “tells” youConvenience, Security All in One “RETRO” REPLACEMENT
Related manuals
Manual 14 pages 5.59 Kb

TRILOG 1200/1500, SC 1200/1500, SILENTMAX 1000/1200, 1200/1500, GPOWER 900 specifications

The Genie TRUE, GPOWER 900, 1200, POWERLIFT 900, and 1500 are renowned products in the field of material handling, specifically designed to enhance efficiency and safety in various lifting applications.

The Genie TRUE is characterized by its innovative design that combines user-friendliness with advanced engineering. This model offers an impressive lift capacity while ensuring stability and performance. Its lightweight structure allows for easy maneuverability, making it ideal for both indoor and outdoor use. The Genie TRUE is equipped with a state-of-the-art control system that provides precise lifting, lowering, and positioning, ensuring maximum productivity for operators.

The GPOWER 900 and 1200 models stand out with their robust build and exceptional lifting capabilities. The GPOWER 900 is designed to handle loads up to 900 pounds, while the GPOWER 1200 can effortlessly lift up to 1200 pounds. Both models use advanced hydraulic systems for smooth operation, allowing for quick lifting cycles without compromising on power or safety. The ergonomic design of the GPOWER series minimizes operator fatigue, making it suitable for prolonged use in various work environments.

The POWERLIFT 900 and 1500 augment this lineup with their impressive features tailored for heavy-duty use. The POWERLIFT 900 can lift loads up to 900 pounds, making it ideal for medium-sized tasks. On the other hand, the POWERLIFT 1500 is engineered for heavier loads, boasting a capacity of 1500 pounds. Both models utilize cutting-edge overload protection technology, ensuring that safety is prioritized during use. Additionally, the POWERLIFT series features an intuitive interface that facilitates easy adjustments and control during operation.

Each of these models embodies the core values of Genie: reliability, innovation, and efficiency. They are designed to meet the varying demands of different industries, including construction, warehousing, and logistics. Their modular designs and interchangeable parts further enhance their versatility and longevity, making them a worthwhile investment for any business needing lifting solutions.

In summary, the Genie TRUE, GPOWER 900, 1200, POWERLIFT 900, and 1500 combine robust performance with safety and ease of use, making them ideal choices for any lifting task. Their reliability and advanced features are sure to meet the growing demands of modern workplaces.
Top Page Image Contents