Harman-Kardon AVR 3000 owner manual System Configuration, Speaker Selection, Speaker Placement

Page 17

System Configuration

When all audio, video and system connections have been made, there are a few configuration adjustments that must be made. A few minutes spent to correctly configure and calibrate the unit will greatly add to your listening experience.

Speaker Selection

No matter which type or brand of speakers is used, the same model or brand of speaker should be used for the front-left, center and front-right speakers. This creates a seamless front soundstage and eliminates the possibility of distracting sonic disturbances that occur when a sound moves across mismatched front-channel speakers.

Speaker Placement

The placement of speakers in a multichannel home-theater system can have a noticeable impact on the quality of sound reproduced.

Depending on the type of center-channel speaker in use and your viewing device, place the center speaker either directly above or below your TV, or in the center behind a perforated front-projection screen.

Once the center-channel speaker is installed, position the left-front and right-front speakers so that they are as far away from one another as the center-channel speaker is from the preferred listening position. Ideally, the front-channel speakers should be placed so that their tweeters are no more than 60cm above or below the tweeter in the center-channel speaker.

They should also be at least 0.5 meter from your TV set unless the speakers are magnetically shielded to avoid colourings on the TV screen. Note that most speakers are not shielded, even with complete surround sets only the Center speaker may be.

Depending on the specifics of your room acoustics and the type of speakers in use, you may find that imaging is improved by moving the front-left and front-right speakers slightly forward of the center-channel speaker. If possible, adjust all front loudspeakers so that they are aimed at ear height when you are seated in the listening position.

Using these guidelines, you’ll find that it takes some experimentation to find the correct location for the front speakers in your particular installation. Don’t be afraid to move things around until the system sounds correct. Optimize your speakers so that audio transitions across the front of the room sound smooth.

Surround speakers should be placed on the side walls of the room, at or slightly behind the listening position. The center of the speaker should face you.

If side-wall mounting is not practical, the speakers may be placed on a rear wall, behind the listening position. The speakers should be no more than two meters behind the rear of the seating area.

Subwoofers produce largely nondirectional sound, so they may be placed almost anywhere in a room. Actual placement should be based on room size and shape and the type of subwoofer used. One method of finding the optimal location for a subwoofer is to begin by placing it in the front of the room, about 15cm from a wall, or near the front corner of the room. Another method is to temporarily place the subwoofer in the spot where you will normally sit, and then walk around the room until you find a spot where the subwoofer sounds best. Place the subwoofer in that spot. You should also follow the instructions of the subwoofer’s manufacturer, or you may wish to experiment with the best location for a subwoofer in your listening room.

Center Front Speaker

No more than 60cm

Left Front

 

Right Front

Speaker

 

Speaker

A)Front Channel Speaker Installation with Direct-View TV Sets or Rear-Screen Projectors

 

 

 

TV or Projection Screen

 

 

Left Front

Center Front

Right Front

 

Speaker

 

Speaker

Speaker

 

 

than 2m

-mounted

are used

 

 

No more

when rear

speakers

 

 

 

 

 

Optional Rear-Wall Mounting

 

B)The distance between the left and right

speakers should be equal to the distance from the seating position to the viewing screen. You may also experiment with placing the left and right speakers slightly forward of the center speaker.

SYSTEM CONFIGURATION 17

Image 17
Contents AVR 3000 Audio/ Video Receiver Declaration of Conformity Table of ContentsIntroduction Description and FeaturesOutput Levels for Optimum PerformanceUnpacking Safety InformationImportant Safety Information Front Panel Controls Front Panel ControlsSee Front Panel Information Display Analog Input Indicator Preset Number/Sleep TimerFront Panel Information Display Front Panel Information Display Rear Panel Connections Rear Panel ConnectionsDigital Audio Outputs Connect these Unswitched Outlet Remote Control Functions Remote Control Functions3000 Channel Direct Input MuteHas been pressed Remote Control FunctionsDirect Input Video Equipment Connections Installation and ConnectionsAudio Equipment Connections Scart A/V Connections Volume on the TV must be reduced to minimumImportant Note for Adapter Cables Important Notes for S-Video connectionsRemote Control Extension System and Power ConnectionsExternal Audio Power Amplifier Connections AC Power ConnectionsSpeaker Placement System ConfigurationSystem Configuration Speaker SelectionSwitched AC outlet Settings to be Made With Each Input UsedUsing the On-Screen Display Selecting the On-Screen displaySpeaker Setup Input SetupSurround Setup Surround Delay Settings Adjustments for Other InputsOutput Level Adjustment Logic delay should be set at twenty millisec- ondsNight Mode Settings Proper Outputs Using EzSetPress and hold the SPL Indicator Select Will change color to indicate the level On the remote only, not the main vol- ume controlsTo turn the test tone off and return to Master MenuOperation Controls and Use of HeadphonesBasic Operation Source SelectionSurround Mode Chart Digital Audio Playback Surround Mode SelectionDolby Digital PCM Audio PlaybackMP3 Audio Playback Digital Status IndicatorsSelecting a Digital Source Rear or front panel #$. In order to proRecord mode Night ModeTape Recording Audio OutputsChannel Direct Input Output Level Trim AdjustmentMemory Backup Recalling Preset Stations Preset TuningTuner Operation Station SelectionRDS Operation RDS TuningRDS Display Options Program Search PTYOperation Turn On Volume Level Advanced FeaturesAdjustment, use the ‹/› buttons E Enter this setting Advanced FeaturesFull-OSD Time Out Adjustment Semi-OSD SettingsProgramming the Remote with Codes Time. When the Program/SPL IndicatorDirect Code Entry Auto-Search MethodProgramming the Remote Erasing Macro CommandsMacro Programming Press the AVR SelectorOperate the Volume Control Volume Punch-ThroughProgrammed Device Functions Remote With Other DevicesChannel Control Punch-Through Resetting the Remote MemoryTon , followed by the VID 2/TV Input Selector buttonFunction List Function ListAVR DVD Setup Code Table TV Neckermann NECNokia NordmendeSetup Code Table VCR Kendo JensenKenwood KoertingCode Number 3digit List Setup Code Table CBLSetup Code Table CD Setup Code Table SAT Code Number 3 Digit List Setup Code Table DVDGoldstar LG RuncoTroubleshooting Guide Troubleshooting GuideProcessor Reset Technical Specifications Harman Consumer International