Harman-Kardon AVR 3000 owner manual See

Page 6

Front Panel Controls

7Surround Mode Selector: Press this but- ton to change the surround mode by scrolling through the list of available modes. Note that Dolby Digital and DTS modes can be selected only when a digital input is used (See page 26 for more information about surround modes.)

8Tuning Selector: Press the left side of the button to tune lower frequency stations and the right side of the button to tune higher frequency stations. When a station with a strong signal is reached, the TUNED indicator Wwill illuminate in the Main Information Display Ú (see page 31 for more information on tuning sta- tions).

9Tuner Band Selector: Pressing this button will automatically switch the AVR to the Tuner mode. Pressing it again will switch between the AM and FM frequency bands, holding it pressed for some seconds will switch between stereo and mono receiving and between automatic and manual tuning mode (See page 31 for more information on the tuner).

)Preset Stations Selector: Press this but- ton to scroll up or down through the list of sta- tions that have been entered into the preset memory. (See page 31 for more information on tuner programming.)

!Input Source Selector: Press this button to change the input by scrolling through the list of input sources.

@RDS Select Button: Press this button to dis- play the various messages that are part of the RDS data system of the AVR 3000’s tuner. (See page 32 for more information on RDS).

#Digital Optical 3 Input: Connect the opti- cal digital audio output of an audio or video prod- uct to this jack. When the Input is not in use, be certain to keep the plastic cap installed to avoid dust contamination that might degrade future performance.

$Digital Coax 3 Input: This jack is normally used for connection to the output of portable digital audio devices, video game consoles or other products that have a coax digital jack.

%Video 4 Input Jacks: These audio/video jacks may be used for temporary connection to video games or portable audio/video products such as camcorders and portable audio players.

^Bass Control: Turn this control to modify the low frequency output of the left/right channels by as much as ±10dB. Set this control to a suitable position for your taste or room acoustics.

&Balance Control: Turn this control to change the relative volume for the front left/right channels.

NOTE: For proper operation of the surround modes this control should be at the midpoint or “12 o’clock” position.

*Treble Control: Turn this control to modify the high frequency output of the left/right chan- nels by as much as ±10dB. Set this control to a suitable position for your taste or room acoustics.

(Volume Control: Turn this knob clockwise to increase the volume, counterclockwise to decrease the volume. If the AVR is muted, adjusting volume control will automatically release the unit from the silenced condition.

ÓSet Button: When making choices during the setup and configuration process, press this button to enter the desired setting as shown in the Main Information Display Úinto the AVR 3000’s memory. The set button may also be used to change the display brightness.

(See page 34.)

ÔInput indicators: A green LED will light in front of the input that is currently being used as the source for the AVR 3000.

Delay: Press this button to begin the sequence of steps required to enter delay time settings. (See page 21 for more information on delay times.)

ÒDigital Input Selector: When playing a source that has a digital output, press this button to select between the Optical # and Coaxial $ Digital inputs. (See pages 27-29 for more information on digital audio.)

ÚMain Information Display: This display delivers messages and status indications to help you operate the receiver. (See pages 7–8 for a complete explanation of the Information Display.)

ÛChannel Select Button: Press this button to begin the process of trimming the channel output levels using an external audio source. (For more information on output level trim adjustment, see page 30.)

ÙSpeaker Select Button: Press this button to begin the process of selecting the speaker positions that are used in your listening room. (See page 19 for more information on setup and configuration.)

ıTest Tone Selector: Press this button to begin the process of adjusting the channel out- put levels using the internal test tone as a refer- ence. (For more information on output level adjustment, see page 22.)

ˆSurround Mode Indicators: A green LED will light in front of the surround mode that is currently in use.

˜Remote Sensor Window: The sensor behind this window receives infrared signals from the remote control. Aim the remote at this area and do not block or cover it unless an external remote sensor is installed.

6FRONT PANEL CONTROLS

Image 6
Contents AVR 3000 Audio/ Video Receiver Table of Contents Declaration of ConformityOutput Levels for Optimum Description and FeaturesIntroduction PerformanceSafety Information Important Safety InformationUnpacking Front Panel Controls Front Panel ControlsSee Analog Input Indicator Preset Number/Sleep Timer Front Panel Information DisplayFront Panel Information Display Front Panel Information Display Rear Panel Connections Digital Audio Outputs Connect theseRear Panel Connections Unswitched Outlet 3000 Remote Control FunctionsRemote Control Functions Channel Direct Input MuteRemote Control Functions Has been pressedDirect Input Installation and Connections Audio Equipment ConnectionsVideo Equipment Connections Important Note for Adapter Cables Volume on the TV must be reduced to minimumScart A/V Connections Important Notes for S-Video connectionsExternal Audio Power Amplifier Connections System and Power ConnectionsRemote Control Extension AC Power ConnectionsSystem Configuration System ConfigurationSpeaker Placement Speaker SelectionUsing the On-Screen Display Settings to be Made With Each Input UsedSwitched AC outlet Selecting the On-Screen displayInput Setup Surround SetupSpeaker Setup Surround Adjustments for Other Inputs Delay SettingsLogic delay should be set at twenty millisec- onds Night Mode SettingsOutput Level Adjustment Using EzSet Press and hold the SPL Indicator SelectProper Outputs To turn the test tone off and return to On the remote only, not the main vol- ume controlsWill change color to indicate the level Master MenuBasic Operation Controls and Use of HeadphonesOperation Source SelectionSurround Mode Chart Dolby Digital Surround Mode SelectionDigital Audio Playback PCM Audio PlaybackSelecting a Digital Source Digital Status IndicatorsMP3 Audio Playback Rear or front panel #$. In order to proTape Recording Night ModeRecord mode Audio OutputsOutput Level Trim Adjustment Memory BackupChannel Direct Input Tuner Operation Preset TuningRecalling Preset Stations Station SelectionRDS Display Options RDS TuningRDS Operation Program Search PTYOperation Adjustment, use the ‹/› buttons E Enter this setting Advanced FeaturesTurn On Volume Level Advanced FeaturesSemi-OSD Settings Full-OSD Time Out AdjustmentDirect Code Entry Time. When the Program/SPL IndicatorProgramming the Remote with Codes Auto-Search MethodMacro Programming Erasing Macro CommandsProgramming the Remote Press the AVR SelectorProgrammed Device Functions Volume Punch-ThroughOperate the Volume Control Remote With Other DevicesTon , followed by the VID 2/TV Input Resetting the Remote MemoryChannel Control Punch-Through Selector buttonFunction List Function ListAVR DVD Setup Code Table TV Nokia NECNeckermann NordmendeSetup Code Table VCR Kenwood JensenKendo KoertingSetup Code Table CBL Code Number 3digit ListSetup Code Table CD Setup Code Table SAT Goldstar LG Setup Code Table DVDCode Number 3 Digit List RuncoTroubleshooting Guide Processor ResetTroubleshooting Guide Technical Specifications Harman Consumer International