Chamberlain MT60P manual Installing the CM128 Wireless Wall Button Optional, Optional accessory

Page 15

26INSTALLING THE CM128 WIRELESS WALL BUTTON (OPTIONAL)

Carefully pry open the CM128 and locate the two screw for mounting.

To attach to the wall, use the two screws and wall anchorsprovided if mount to plaster wall (if using a recessed wall box do not useanchors).

NOTE: Tightening the wall mount screws will reduce clearance between bracket and wall.

NOTE: Your CM128 Wireless door controller should be pre-

 

 

programmed into your unit, you should only need to program

 

 

additional units.

 

+

Program the Wall control into the Rolling Code Receiver

+

 

Using the orange “LEARN” Button:

 

+

 

 

1. Press and hold down the button you wish to program to the

 

 

opener. The orange LED will flash to indiciate it is receiving signal from

the transmitter.

 

 

2. Press and release the “LRN” button.

 

 

3. The sourtesy LEDs will flash once.

 

 

Locate minimum 1.5m above

Ensure the door is clear of obstruction, then test the transmitterhe floor. .

14

27WIRELESS PROGRAMMING (OPTIONAL ACCESSORIES)

Activate the opener only when door is in full view, free of obstruction and properly adjusted. No one should enter or leave garage while door is in motion. Do not allow children to operate push button(s) or remote(s). Do not allow children to play near the door.

NOTE: The transmitter(s) and wall button supplied with your opener are factory programmed.

If you purchase additional transmitters, the garage door

opener must be programmed to accept the new remote

 

 

 

code.

 

 

 

Program the Receiver to Match Additional Transmitter

 

 

 

Codes:

 

 

 

Using the orange “LEARN” Button:

 

 

 

1. Press and hold down the transmitter button you wish to

 

 

 

program to the opener. The orange LED will flash to

 

 

 

indiciate it is receiving signal from the transmitter.

 

 

 

2. Press and release the “LRN” button.

 

 

 

3. The sourtesy LEDs will flash once.

 

 

 

Ensure the door is clear of obstruction, then test the

 

 

transmitter.

1

2

3

Using the Motion Detecting Control Panel

 

 

 

(optional accessory):

 

merlin+

 

 

 

 

1.Press and hold the button on the hand-held remote that you wish to operate your garage door (1).

2.While holding the remote button, press and hold the

LIGHT button on the Motion Detecting Control Panel (2).

3.Continue holding both buttons while you press the push

bar on the Motion Detecting Control Panel (all three buttons are held) (3).

4.Release buttons when the opener light flashes. It has learned the code. If the light bulb is not installed, two clicks will be heard (4).

Now the opener will operate when the transmitter push

 

 

 

 

 

button is pressed. If you release the transmitter push button

 

 

 

before the opener light flashes, the opener has not learned

 

 

 

the code.

 

1

2

3

4

To Erase all Transmitter Codes:

merlin+

 

LOCK

 

 

To deactivate any unwanted remote, first erase all codes:

 

 

LIGHT

 

 

Press and hold the orange “learn” button on opener until

 

 

 

 

the learn indicator light goes out (approximately 6 seconds).

 

 

 

 

All previous codes are now erased. Reprogram each remote or keyless entry

 

 

you wish to use.

 

 

 

 

 

Page 14 Page 16
Image 15
Page 14 Page 16
Contents MT60P Start by Reading These Important Safety Instructions Hardware Provided Installation HardwareDoor Types Tools RequiredMT60P Opener Carton Not PicturedCompleted Installation Tilt Door Example Shown Before YOU BeginAssemble Pole Pack Install the Stop Collar and Pole Install the Pole AdaptorFitting the Chain Install the ChainInstall the Header Bracket Created in for proper placement of header BracketPosition the Header Bracket ONE Piece Tilt Door Attach Pole Assembly to Header BracketPosition the Opener Sectional Door or Tracked Tilt DoorFraying Hang the OpenerAttach Emergency Release Rope & Handle AnglesDo . not bend at the bracket holesInstall Light Connecting Door ARM ONE Piece DoorsFasten Door Bracket Connect Door ARM Sectional Doors Connect Electric PowerSetting the Force Setting the limitsComplete your installation refer section Install the Protector System Test the Safety Reverse SystemOptional accessory Installing the CM128 Wireless Wall Button OptionalWireless Programming Optional Accessories Using the Motion Detecting Control PanelKeyless Devices Programming Optional Accessories Operation of the Door Control Install Door Control OptionalDoor within a door connection Special FeaturesAccessories Replacement Parts Replacement Parts Once a MonthOnce a Year Trouble Shooting Operation of Your Opener Chamberlain Limited Warranty

MT60P specifications

The Chamberlain MT60P is a state-of-the-art garage door opener that combines advanced technology with user-friendly features, making it one of the best choices for homeowners seeking reliability and convenience. This model is designed to cater to various needs while ensuring safety and efficiency.

One of the standout features of the Chamberlain MT60P is its powerful motor, which provides a lifting capacity of up to 600 pounds. This robust operation is suitable for heavy and Michigan weather conditions, delivering consistent performance day in and day out. The durable design ensures longevity, allowing it to handle the rigors of daily use.

The MT60P leverages innovative MyQ technology, which allows users to operate and monitor their garage door remotely through a smartphone app. This feature adds a layer of convenience, enabling users to check whether their garage door is open or closed from anywhere. The app also sends alerts and notifications, providing peace of mind for users concerned about security.

Another notable characteristic of the Chamberlain MT60P is its quiet operation. Equipped with a belt drive system, the opener operates smoothly and silently, making it ideal for homes with bedrooms adjacent to the garage. This feature significantly reduces noise, allowing for a peaceful environment even when the garage door is in use.

Safety is also a top priority for the MT60P. The opener includes safety sensors that detect obstructions in the door's path, reversing the door's direction if anything is detected. This technology helps prevent accidents and protects pets, vehicles, and family members.

Installation of the Chamberlain MT60P is designed to be straightforward, with a user-friendly process that allows homeowners to set it up with minimal effort. Additionally, the garage door opener is compatible with most standard garage doors, enhancing its versatility.

Furthermore, the MT60P comes with two remote controls and a keypad for added accessibility. This feature allows multiple users to access the garage easily, reducing the hassle of forgetting keys or entering codes.

In summary, the Chamberlain MT60P stands out with its advanced motor performance, MyQ technology, quiet operation, and safety features, making it a top choice for garage door openers. Its combination of durability, convenience, and technological innovation addresses modern homeowner needs, ensuring satisfaction for years to come.
Top Page Image Contents