Berkley B2ZRKL, B3TRKS, B4ZRKS, B2XRKS owner manual Pressure, When Flooded Suction Exists

Page 10

Installation

Suction Connection

When Flooded Suction Exists

 

 

Water under

 

 

pressure

Pump driven by remote

 

Maintain minumum

power source, direct

Short run of straight pipe after

liquid level to prevent

coupling or pulley/belt

vortexing.

connection.

reducer (2 times pipe diameter).

 

 

Eccentric Reducer

 

 

flat side up.

 

 

Suction

 

 

Gauge

 

2214 0196

 

Isolation Valve

 

 

 

 

full open when

See foundation

 

pumping.

section.

Straight run, short as possible but

 

 

 

 

at least 6 times pipe diameter after

 

 

pipe fitting to stabilize flow.

 

 

Slope upward to pump.

 

Support pipe

Standard or

as required

long radius

 

elbow.

Use pipe, tubing, or reinforced hose to make suction connection. Hose must have sufficient strength to resist collapse under the atmospheric pressure differential that may occur while pump is running.

It is important, even with a flooded suction condition, that proper pipe fittings are used so water is delivered to impeller eye with a smooth flow and consistent velocity.

Suction pipe size should be at least one commercial pipe size larger than opening of pipe inlet. Flow velocity should not exceed 8 ft./sec.

An isolation valve is used in a pressurized suction pipe to permit servicing pump.

Piping run and connection fittings should be properly aligned and independently supported to reduce strain on pump case.

If solids are present, a strainer should be used to protect the pump.

Recommended

Page 10

F00633

Image 10
Contents Self Prime Frame Mounted Centrifugal Pump Pump Location Read and Follow Safety InstructionsGeneral Information LocationPiping Suction PipingDischarge Piping Electrical ConnectionTypical Installations Pump FoundationAlignment of Pump and Motor Shaft Direct Coupling DriveShaft Alignment Course AlignmentAlignment Belt DriveAlignment/Proper Belt Tension TensionElectric Motor / Hydraulic Motor Mounting Hydraulic Motor and AdapterSuction Connection Suction LiftNot Recommended When Flooded Suction Exists PressureWater under Pressure Discharge Connection Align piping to minimize flange stressDo not force alignment that can cause flange stresses Electric Motors Check RotationPriming Engine DrivenPerformance Check Observational MaintenanceLubrication RepackingInstalling New Rings Packing Ring ReplacementRemoval General Pump Care Ordering Replacement Parts Berkeley PumpsSelf Prime Bearing Frame Parts BreakdownTroubleshooting Electrical Drive PumpsProbable Cause Symptom Group Engine Mechanical System Engine Drive PumpsII. Quarterly Inspection Routine InspectionQuarterly Inspection III. Quarterly Inspection IV. Quarterly InspectionMaintenance Warranty General Terms and Conditions

B2XRKS, B2ZRKL, B3TRKS, B4ZRKS specifications

The Berkley B2XRKS, B2ZRKL, B3TRKS, and B4ZRKS are innovative fishing rods designed to enhance the angling experience for both novice and experienced anglers. These rods are renowned for their performance, durability, and advanced technologies, making them stand out in the marketplace.

The B2XRKS model incorporates a lightweight yet robust construction that allows for excellent casting accuracy and control. Made from high-quality materials, this rod features a sensitive tip to detect even the slightest nibble, enhancing the chances of a successful catch. The ergonomic handle provides comfort during long fishing sessions, minimizing fatigue and improving grip.

Berkley's B2ZRKL is tailored specifically for versatility in various fishing scenarios. Its medium to heavy power rating accommodates different fishing techniques, from bass to trout. The rod's backbone offers enough strength to handle larger fish, while still maintaining the sensitivity required for finesse presentations. This model is equipped with high-performance guides that promote smoother line flow, reducing friction and enhancing casting distance.

The B3TRKS model takes innovation a step further by integrating cutting-edge anti-tangle technology. This feature dramatically reduces the chances of line tangles, allowing anglers to focus solely on their fishing. Additionally, the B3TRKS is designed with a seamless blank construction, enhancing durability and performance. The rod’s lightweight design does not compromise its strength, making it ideal for extended use.

Lastly, the B4ZRKS model stands out for its advanced construction methodologies. Utilizing a unique blend of materials, this rod achieves an optimal balance of weight and power. It features a precision-molded tip, providing unparalleled sensitivity and responsiveness. The B4ZRKS also benefits from a specialized grip system that ensures a secure hold even in wet conditions, enhancing performance during challenging weather.

In summary, the Berkley B2XRKS, B2ZRKL, B3TRKS, and B4ZRKS rods offer a range of features that cater to various fishing styles and preferences. Their incorporation of advanced technologies and premium materials ensures that anglers can rely on these rods for both performance and durability. Whether casting for bass or reeling in trout, these rods are designed to maximize the fishing experience, making them an excellent choice for any angler looking to improve their craft.