Lubrication, Performance Check, Repacking, Shaft

Maintenance

General Information

LUBRICATION:

LIQUID END of pump requires no lubrication. Wear rings, packing rings, and models using a mechanical shaft seal, are lubricated by the liquid being pumped. Do not run dry!

BEARING FRAME - add approximately 2 ounces of a lithium-based NGLI No. 2 extra pressure ball bearing grease to each bearing during quarterly inspection.

NOTE: Excess grease will cause bearings to run hot.

The following are factory approved brands of grease for use with Berkeley Pumps: Alvania EP2, Shell Oil; Mobilith AW2, Mobil Oil, Ronex MP, Exxon, Litholine EP2, Atlantic Richfield; and Amolith EP2, Amoco.

ELECTRIC MOTOR: Refer to motor manufacturer’s operating manual for complete instruction.

GAS/DIESEL ENGINE: Refer to engine manufacturer’s operating manual for complete instruction.

PERFORMANCE CHECK:

Periodically check the output of the pump. If perform- ance is noticeably reduced, refer to Troubleshooting Chart.

OBSERVATIONAL MAINTENANCE:

When the pump and system operation have been stabilized, verify that pump unit is operating properly. Observe the following:

VIBRATION: All rotating machines can be expected to produce some vibration, however, excessive vibration can reduce the life of the unit. If the vibration seems excessive, discontinue operation, determine cause of the excessive vibration, and correct.

NOISE: When the unit is operating under load, listen closely for unusual sounds that might indicate that the unit is in distress. Determine the cause and correct.

OPERATING TEMPERATURE: During operation, heat is dissipated from the pump and the driver. After a short period of time, the surface of the pump bracket will be quite warm (as high as 150°F), which is normal. If the surface temperature of the pump bracket or driver is excessive, discontinue operation, determine cause of the excessive temperature rise, and correct.

Bearings will run hotter for a brief run-in period after packing which is normal. However, worn bearings will cause excessive temperatures and need to be replaced. The pump unit is cooled by the water flowing through it, and will normally be at the temperature of the water being pumped.

STUFFING BOX: After a short period of operation, verify that the stuffing box area and gland are not hot. If heating is detected, loosen the gland nuts evenly until water is just running out of stuffing box in a DROPLET form (approximately 40-60 drops per minute). Water must not be streaming or spraying out. Verify cool operation periodically. Adjust gland nuts EVENLY as necessary for lubrication and cooling of the packing. If packing has been tightened to the limit of the packing gland travel, additional packing is necessary.

PUMPS WITH PACKING: Starting new pump.

Before starting pump for the first time, loosen gland nuts and retighten finger tight. Proceed with pump start-up procedure. Allow packing to leak liberally for a few moments. Then tighten gland nuts one complete turn each until leakage is reduced to 40 to 60 drops per minute.

REPACKING:

Refer to illustration on Page 16.

PUMPS WITH MECHANICAL SEAL:

Adjustment or maintenance is normally not required. The seal is enclosed within the pump and is self adjusting. Seal is cooled and lubricated by the liquid being pumped. Consult factory for proper replacement procedure.

SHAFT:

Bearing frame shaft assemblies should be periodically torn down for inspection of worn parts, cleaning and re- greasing. Most importantly, to check shaft sleeve and bearings for pitting. Replace worn components as necessary.

F00633

Page 15

B2XRKS, B2ZRKL, B3TRKS, B4ZRKS specifications

The Berkley B2XRKS, B2ZRKL, B3TRKS, and B4ZRKS are innovative fishing rods designed to enhance the angling experience for both novice and experienced anglers. These rods are renowned for their performance, durability, and advanced technologies, making them stand out in the marketplace.

The B2XRKS model incorporates a lightweight yet robust construction that allows for excellent casting accuracy and control. Made from high-quality materials, this rod features a sensitive tip to detect even the slightest nibble, enhancing the chances of a successful catch. The ergonomic handle provides comfort during long fishing sessions, minimizing fatigue and improving grip.

Berkley's B2ZRKL is tailored specifically for versatility in various fishing scenarios. Its medium to heavy power rating accommodates different fishing techniques, from bass to trout. The rod's backbone offers enough strength to handle larger fish, while still maintaining the sensitivity required for finesse presentations. This model is equipped with high-performance guides that promote smoother line flow, reducing friction and enhancing casting distance.

The B3TRKS model takes innovation a step further by integrating cutting-edge anti-tangle technology. This feature dramatically reduces the chances of line tangles, allowing anglers to focus solely on their fishing. Additionally, the B3TRKS is designed with a seamless blank construction, enhancing durability and performance. The rod’s lightweight design does not compromise its strength, making it ideal for extended use.

Lastly, the B4ZRKS model stands out for its advanced construction methodologies. Utilizing a unique blend of materials, this rod achieves an optimal balance of weight and power. It features a precision-molded tip, providing unparalleled sensitivity and responsiveness. The B4ZRKS also benefits from a specialized grip system that ensures a secure hold even in wet conditions, enhancing performance during challenging weather.

In summary, the Berkley B2XRKS, B2ZRKL, B3TRKS, and B4ZRKS rods offer a range of features that cater to various fishing styles and preferences. Their incorporation of advanced technologies and premium materials ensures that anglers can rely on these rods for both performance and durability. Whether casting for bass or reeling in trout, these rods are designed to maximize the fishing experience, making them an excellent choice for any angler looking to improve their craft.