Berkley B3TRKS, B4ZRKS, B2ZRKL, B2XRKS Packing Ring Replacement, Removal, Installing New Rings

Page 16

Maintenance

Packing Ring Replacement

Removal

Packing

Gland

Shaft

2 x Scale

1

 

Packing

Hooks

 

Packing

2239 0196

Ring

2

Unfasten hardware holding Packing Gland in place and slide back on shaft to expose packing rings.

Remove packing rings from Stuffing box using two commercially available Packing Hooks as shown.

Slide Lantern Ring (if used) back to expose any remaining rings, including metallic. Remove them in the same manner.

Installing New Rings

Stagger ring joints 90 degrees apart

Packing Rings

Shaft

2240 0196

Metallic Ring

Lantern Ring

Clean shaft sleeve and Packing Gland.

Inspect shaft sleeve for wear, replace if needed.

Install new packing rings in stuffing box by placing over shaft sleeve and pushing them in as far as they will go.

Rotate ring joint 90 degrees when installing each ring as shown.

Slide packing gland into position, then gently and evenly tighten nuts to force rings into place and seat (do not overtighten). Loosen nuts again to hand tight.

Start primed pump and allow packing to leak liberally.

Tighten gland nuts one complete turn each until leakage is reduced to 40 to 60 drops per minute.

Page 16

F00633

Image 16
Contents Self Prime Frame Mounted Centrifugal Pump Read and Follow Safety Instructions General InformationPump Location LocationSuction Piping Discharge PipingPiping Electrical ConnectionTypical Installations Pump FoundationDirect Coupling Drive Shaft AlignmentAlignment of Pump and Motor Shaft Course AlignmentBelt Drive Alignment/Proper Belt TensionAlignment TensionElectric Motor / Hydraulic Motor Mounting Hydraulic Motor and AdapterSuction Connection Suction LiftNot Recommended When Flooded Suction Exists PressureWater under Pressure Discharge Connection Align piping to minimize flange stressDo not force alignment that can cause flange stresses Check Rotation PrimingElectric Motors Engine DrivenObservational Maintenance LubricationPerformance Check RepackingInstalling New Rings Packing Ring ReplacementRemoval General Pump Care Ordering Replacement Parts Berkeley PumpsSelf Prime Bearing Frame Parts BreakdownTroubleshooting Electrical Drive PumpsProbable Cause Symptom Group Engine Mechanical System Engine Drive PumpsRoutine Inspection Quarterly Inspection III. Quarterly InspectionII. Quarterly Inspection IV. Quarterly InspectionMaintenance Warranty General Terms and Conditions

B2XRKS, B2ZRKL, B3TRKS, B4ZRKS specifications

The Berkley B2XRKS, B2ZRKL, B3TRKS, and B4ZRKS are innovative fishing rods designed to enhance the angling experience for both novice and experienced anglers. These rods are renowned for their performance, durability, and advanced technologies, making them stand out in the marketplace.

The B2XRKS model incorporates a lightweight yet robust construction that allows for excellent casting accuracy and control. Made from high-quality materials, this rod features a sensitive tip to detect even the slightest nibble, enhancing the chances of a successful catch. The ergonomic handle provides comfort during long fishing sessions, minimizing fatigue and improving grip.

Berkley's B2ZRKL is tailored specifically for versatility in various fishing scenarios. Its medium to heavy power rating accommodates different fishing techniques, from bass to trout. The rod's backbone offers enough strength to handle larger fish, while still maintaining the sensitivity required for finesse presentations. This model is equipped with high-performance guides that promote smoother line flow, reducing friction and enhancing casting distance.

The B3TRKS model takes innovation a step further by integrating cutting-edge anti-tangle technology. This feature dramatically reduces the chances of line tangles, allowing anglers to focus solely on their fishing. Additionally, the B3TRKS is designed with a seamless blank construction, enhancing durability and performance. The rod’s lightweight design does not compromise its strength, making it ideal for extended use.

Lastly, the B4ZRKS model stands out for its advanced construction methodologies. Utilizing a unique blend of materials, this rod achieves an optimal balance of weight and power. It features a precision-molded tip, providing unparalleled sensitivity and responsiveness. The B4ZRKS also benefits from a specialized grip system that ensures a secure hold even in wet conditions, enhancing performance during challenging weather.

In summary, the Berkley B2XRKS, B2ZRKL, B3TRKS, and B4ZRKS rods offer a range of features that cater to various fishing styles and preferences. Their incorporation of advanced technologies and premium materials ensures that anglers can rely on these rods for both performance and durability. Whether casting for bass or reeling in trout, these rods are designed to maximize the fishing experience, making them an excellent choice for any angler looking to improve their craft.