Main Remote Control Functions
KTuning Up/Down: When the tuner is in use, these buttons will tune up or down through the selected frequency band. If the Tuner Mode but- ton Ihas been pressed or the Band button ! on the front panel was held pressed so that AUTO appears in the Main Information Display ˜, pressing either of the buttons will cause the tuner to seek the next station with acceptable signal strength for quality reception. When the MANUAL appears in the Main Information Display ˜, pressing these but- tons will tune stations in
LOSD Button: Press this button to activate the On Screen Display (OSD) system used to set up or adjust the AVR’s parameters.
MDolby Mode Selector: This button is used to select one of the available Dolby Surround processing modes. Each press of this button will select one of the Dolby Pro Logic II modes, Dolby 3 Stereo or Dolby Digital. Note that the Dolby Digital mode is only available with a digital input selected and the other modes only as long as a Dolby Digital source is not playing (except Pro Logic II with Dolby Digital 2.0 recordings, see Note on page 7). See page 29 for the available Dolby surround mode options.
NDTS Digital Mode Selector: When a DTS source is in use the AVR will select the appropri- ate mode automatically and no other mode will be available. Pressing this button will display the mode currently selected by the AVR´s decoder, depending on the surround material played and the speaker setting (see item 6, page 5). When a DTS source is not in use, this button has no function. (See page 24, 29 for the available DTS options.)
OLogic 7 Selector: Press this button to select one of the available Logic 7 surround modes. (See page 29 for the available Logic 7 options.)
PTransport Control Buttons: These but- tons do not have any functions for the AVR, but they may be programmed for the forward/reverse play operation of a wide variety of CD or DVD players, and audio or video- cassette recorders. (See page 42 for more information on program- ming the remote.)
QLight Button: Press this button to activate the remote’s
Skip Up/Down Buttons: These buttons do not have a direct function with the AVR, but when used with a compatibly programmed CD or DVD player/changer they will change the tracks on the disc currently being played.
Stereo Mode Selector: Press this button to select a stereo playback mode. When the but- ton is pressed so that DSP SURR OFF appears in the Main Information Display ˜, the AVR will operate in a bypass mode with true fully analog,
DTS Neo:6 Mode Selector: Pressing this selector button cycles the AVR through the various DTS Neo:6 modes, which extract a five- or
DTS Neo:6 MUSIC 
DTS Neo:6
MOVIES
Macro Buttons: Press these buttons to store or recall a “Macro”, which is a
RDS Select Button: Press this button to display the various messages that are part of the RDS data system of the AVR’s tuner. (See page 41 for more information on RDS).
Preset Up/Down: When the tuner is in use, press these buttons to scroll through the stations programmed into the AVR’s memory. When CD or DVD is selected using the Input Selector button 4, these buttons may func- tion as Slow Fwd/Rev (DVD) or ”+10” (CD, CDR).
Clear Button: Press this button to clear incorrect entries when using the remote to directly enter a radio station’s frequency.
Memory Button: Press this button to enter a radio station into the AVR’s preset memory. Two underline indicators will flash at the right side of the Main Information Display ˜, you then have five seconds to enter a preset memory loca- tion using the Numeric Keys H. (See page 40 for more information.)
Delay Select Button: This button selects adjustments to the A/V Sync Delay and the indi- vidual channel displays. The first press of the but- ton displays an A/V SYNC DELAY message in the Lower Display Line ˜ and in the on- screen display, which means that you may change the amount of time that all channels are delayed together behind the video. This enables you to compensate for the loss of lip sync that may be caused by digital video processing in your display or by television stations. To change the A/V Sync Delay, press the Set Button F while the A/V SYNC DELAY message is visible and then use the ⁄/¤ Navigation Button Eto change the setting so that the sound and the video image are in sync. To change the delay for an individual output chan- nel, press the ⁄/¤ Navigation Button E until the desired channel name is shown, and then press the Set Button F. Use the ⁄/¤ Navigation Buttons Eto change the delay amount. (See page 26 for more information on delay options.)
Program Button: This button is used to begin the process of programming the remote. Press and hold this button for three seconds to place the remote in the programming mode.
Once the red LED under the Set Button F lights, release the button. You may then select from the desired option. (See pages 42 – 51 for more information on configuring the remote.)
Speaker Select: Press this button to begin the process of configuring the AVR’s Bass Management System for use with the type of speakers used in your system. Once the button has been pressed, use the ⁄/¤ buttons Eto select the channel you wish to set up. Press the Set Button Fand then select the speaker type (Large, Small or None) appropriate with the speaker in use. (See page 21 for more informa- tion.)
Volume Up/Down: Press these buttons to raise or lower the system volume.