Rear Panel Connections
Video Monitor Outputs: Connect this jack to the composite and/or
DVD Video Inputs: Connect these jacks to the composite or
Front Speaker Outputs: Connect these outputs to the matching + or – terminals on your left and right speakers. In conformance with the new CEA color code specification, the White terminal is the positive, or "+" terminal that should be connected to the red (+) terminal on Front Left speaker with the older color coding, while the Red terminal is the positive, or "+" terminal that should be connected to the red (+) terminal on Front Right speaker. Connect the black
Center Speaker Outputs: Connect these outputs to the matching + and – terminals on your center channel speaker. In conformance with the new CEA color code specification, the Green Terminal is the positive, or "+" terminal that should be connected to the red (+) terminal on speakers with the older color coding. Connect the black
Surround Speaker Outputs: Connect these outputs to the matching + and – terminals on your surround channel speakers. In confor- mance with the new CEA color code specifica- tion, the Blue terminal is the positive, or "+" terminal that should be connected to the red (+) terminal on the Surround Left speaker with older color coding, while the Gray terminal should be connected to the red (+) terminal on the Surround Right speaker with the older color cod- ing. Connect the black
Switched AC Accessory Outlet: This out- let may be used to power any device that you wish to have turn on when the AVR is turned on with the System Power Control switch 2.
Unswitched AC Accessory Outlet: This outlet may be used to power any AC device. The power will remain on at this outlet regardless of whether the AVR is on or off (in Standby), pro- vided that the Main Power switch 1 is on.
Note: The total power consumption of all devices connected to the accessory outlets should not exceed 100 watts from the
Unswitched Outlet | and 50 W from the |
Switched Outlet . |
|
AC Power Cord Jack: Connect the AC
power cord to this jack when the installation is complete. To ensure safe operation, use only the power cord supplied with the unit. If a replace- ment is required it must be of the same type and capacity.
Component Video 2 Inputs: These inputs may be used with any video source device equipped with analog Y/Pr/Pb or RGB com- ponent video outputs. The factory default is for these jacks to be a linked to the Video 2 input, but you may change the setting at any time through the IN/OUT SETUP menu. See page 15 for more information on configuring the component video inputs.
Monitor Component Video Outputs: Connect these outputs to the component video inputs of a video projector or monitor. When a source connected to one of the two
Component Video Inputs is selected the signal will be sent to these jacks.
Component Video 1 Inputs: These inputs may be used with any source device equipped with analog Y/Pr/Pb or RGB component video outputs. The factory default is for these jacks to be a linked to the DVD input, but you may change the setting at any time through the IN/OUT SETUP menu. See page 15 for more information on configuring the component video inputs.
Note: All component inputs/outputs can be used for RGB signals too, in the same way as described for the Y/Pr/Pb signals, then connected to the jacks with the corresponding color.
RGB connection is not possible if the source out- puts a separate sync signal (see page 16).
Remote IR Output: This connection permits the IR sensor in the receiver to serve other remote controlled devices. Connect this jack to the “IR IN” jack on Harman Kardon or other compatible equipment.
Remote IR Input: If the AVR’s
Multiroom IR Input: Connect the output of an IR sensor in a remote room to this jack to operate the AVR’s multiroom control system.
Video 1 Video Outputs: Connect these jacks to the RECORD/INPUT composite or
Video 1 Video Inputs: Connect these jacks to the PLAY/OUT composite or
Video 2 Video Outputs: Connect these jacks to the RECORD/INPUT composite or
Video 3 Video Inputs: Connect these jacks to the PLAY/OUT composite or
Video 2 Video Inputs: Connect these jacks to the PLAY/OUT composite or
Optical Digital Inputs: Connect the optical digital output from a DVD player, HDTV receiver, the S/PDIF output of a compatible com- puter sound card playing MP3 files or streams, LD player, MD player or CD player to these jacks. The signal may be either a Dolby Digital signal, a DTS signal, a 2 channel MPEG 1 signal, an MP3 or HDCD data stream or a standard PCM digital source.
Coaxial Digital Inputs: Connect the coax digital output from a DVD player, HDTV receiver, the S/PDIF output of a compatible computer sound card playing MP3 files or streams, LD player, MD player or CD player to these jacks. The signal may be either a Dolby Digital signal, DTS signal, a 2 channel MPEG 1 signal, an MP3 or HDCD data stream or a standard PCM digital source. Do not connect the RF digital output of an LD player to these jacks.
Video 2 Audio Outputs: Connect these jacks to the RECORD/INPUT audio jacks on a VCR or any Audio recorder.
Video 2 Audio Inputs: Connect these jacks to the PLAY/OUT audio jacks on a second VCR or other audio or video source.
Video 3 Audio Inputs: Connect these jacks to the PLAY/OUT audio jacks on any audio or video source.
Video 1 Audio Inputs: Connect these jacks to the PLAY/OUT audio jacks on a VCR or other audio or video source.
Video 1 Audio Outputs: Connect these jacks to the RECORD/INPUT audio jacks on a VCR or any other Audio recorder.
8REAR PANEL CONNECTIONS