Harman-Kardon + and negative -terminals, AVR 630 when appropriate upgrades are available

Page 9

(+) and negative (–) terminals.

Rear Panel Connections

Preamp Outputs: Connect these jacks to an optional, external power amplifier for appli- cations where higher power is desired.

Surround Back/Multiroom Speaker Outputs: These speaker terminals are normally used to power the surround back left/surround back right speakers in a 7.1 channel system. However, they may also be used to power the speakers in a second zone, which will receive the output selected for a multiroom system.

To change the output fed to these terminals from the default of the Surround Back speakers to the Multiroom Output, you must change a setting in the Advanced Menu of the OSD sys- tem. See page 37 for more information on con- figuring this speaker output. In normal surround system use, the brown and black terminals are the surround back left channel positive (+) and negative (–) connections and the tan and black terminals are the surround back right positive

(+) and negative (–) terminals.

For multiroom use, connect the brown and black SBL terminals to the red and black connections on the left remote zone speaker and connect the tan and black SBR terminals to the red and black terminals on the right remote zone speaker.

RS-232 Port: This jack may be used to con- trol the AVR 630 over a bi-directional RS-232 serial control link to a compatible computer or programmable remote control system. Due to the complexity of programming RS-232 com- mands we strongly recommend that connections to this port for control purposes be made by a trained and qualified technician. This jack may also link to a compatible computer to upgrade the software and operating system of the

AVR 630 when appropriate upgrades are available.

Fan Vents: These ventilation holes are the output of the AVR’s airflow system. To ensure proper operation of the unit and to avoid possi- ble damage to delicate surfaces, make certain that these holes are not blocked and that there is at least three inches of open space between the vent holes and any wooden or fabric surface.

REAR PANEL CONNECTIONS 9

Image 9

Contents AVR 630 Audio/ Video Receiver Declaration of Conformity Table of ContentsWe, Harman Consumer International 2, route de Tours 72500 Château-du-Loir FRANCEIntroduction Description and FeaturesMultiple digital inputs and outputs On-screenmenu and display systemImportant Safety Information Introduction / Safety Information4INTRODUCTION / SAFETY INFORMATION Handle the AC Power Cord Gently2 System Power Control 1 Main Power Switch3 Power Indicator Tuning Selector33 for more information Coaxial ÓFront Panel Controls 6FRONT PANEL CONTROLSDigital Audio Outputs Connect these Rear Panel ConnectionsSwitched Outlet Unswitched OutletAC Power Cord Jack Connect the AC Rear Panel Connections+ and negative -terminals AVR 630 when appropriate upgrades are availableRear Panel Connections REAR PANEL CONNECTIONSMain Remote Control Functions 1 0H I D C E G F P P P MAIN REMOTE CONTROL FUNCTIONS Main Remote Control Functions8-ChannelDirect Inputs the input GDigital Select Press this button to assign12MAIN REMOTE CONTROL FUNCTIONS Main Remote Control FunctionsDTS Neo 6 MUSIC DTS Neo 6 MOVIES MAIN REMOTE CONTROL FUNCTIONS Main Remote Control Functions14ZONE II REMOTE CONTROL FUNCTIONS Zone II Remote Control FunctionsINSTALLATION AND CONNECTIONS Installation and ConnectionsAudio Equipment Connections Video Equipment Connections16INSTALLATION AND CONNECTIONS Important Notes for S-VideoconnectionsSCART A/V Connections Video Audio InputsIf you use a unit providing RGB signals on a Note for RGB signal with SCARTImportant Note for the Use of SCART-CinchAdapters Installation and ConnectionsMain Room Remote Control Extension System and Power ConnectionsRS-232Connections AC Power ConnectionsSpeaker Selection Speaker PlacementBThe distance between the left and right Installation and ConnectionsUsing the On-ScreenDisplay System ConfigurationSystem Setup Input SetupComponent Video Inputs may be SYSTEM CONFIGURATIONSet Button F System Configuration22SYSTEM CONFIGURATION Audio SetupSpeaker Setup Fto bring up the SPEAKER SETUP menu FigureSYSTEM CONFIGURATION System ConfigurationSystem Configuration Surround SetupButton Eso that SURROUND Adjustments for Other Inputspresss the Set Button F System ConfigurationNight Mode Settings Delay Settings26SYSTEM CONFIGURATION individually for each input in useOutput Level Adjustment setting, then press Set Fto confirm the set- tingUsing EzSet 3.Press and hold the SPL Select ButtonEon the remote 28SYSTEM CONFIGURATION1.Press and hold the SPL Select Button press the Clear ButtonFEATURES Surround Mode ChartOperation MODEFEATURES Surround Mode ChartOperation MODEUsing the Sleep Timer Switched AC Outlets and the Power8-ChannelDirect Inputs and when the Basic OperationVolume Up/Down Controls and Use of HeadphonesOne of the most important features of the Surround Mode SelectionDolby Digital Digital Audio Playbackrear panel or front panel *ÓSpeaker/Channel Indicators Digital Bitstream Indicators2.0audio, while the main feature is available in Selecting a Digital SourceFront Panel In/Outputs Tape RecordingNight Mode puts for Tape OutputsMemory Backup Output Level Adjustment With Source SignalsDim Function OperationTurn On Volume Level Advanced FeaturesADVANCED FEATURES Surround Amplifier Channel AssignmentSemi-OSDSettings Advanced Features / Multiroom OperationFull-OSDTime Out Adjustment Installationlocation volume Multiroom Setupfrequency Kè, change the tuner preset Multiroom OperationRecalling Preset Stations Preset TuningMultiroom Operation / Tuner Operation Basic Tuner OperationTuner Operation RDS TuningRDS Operation RDS Display OptionsProgramming the Remote Configuring the RemotePreprogrammed Code Entry FappearsProgramming the Remote Learning CommandsAutomatic Code Entry PROGRAMMING THE REMOTEChanging Devices 44PROGRAMMING THE REMOTEProgramming the Remote Recording a Macro Macro ProgrammingProgramming the Remote PROGRAMMING THE REMOTEPower On VID 2/TV Power On VID 3/Cable Punch-ThroughConfigurationPower On AVR Logic 7 O Erasing a MacroNote for Volume Punch-Through Volume Punch-ThroughChannel Punch-Through red. Press the ⁄¤ Navigation ButtonsTransport Punch-Through EzSet Configuration⁄¤ Navigation Buttons Eonce so that 4. Within five seconds, press the Set ButtonRenaming a Device RenamingNotes on Renaming Devices ‹/› Navigation Buttons Eas requiredFigure Figure Resetting the Remote11.At this point you have two options Notes on Renaming KeysPROGRAMMING THE REMOTE Programming the RemoteT I M E O U T O R C L R K E Y P R E S S E D A V R L O W B A T T E R YProcessor Reset Troubleshooting GuideSYMPTOM SOLUTIONAudio Section Technical SpecificationsFM Tuner Section AM Tuner SectionPart No. ZKD0201HA00-4 Harman Consumer International