Surround Setup, System Configuration

System Configuration

main front left/right speakers, regardless of the type of program source or Surround mode you are listening to, press the ‹/› Buttons Eon the remote so that SUB L/R+LFE appears in the on-screen menu. When this option is selected, a full-range signal will be sent to the front left/right “main” speakers. The subwoofer will receive the front left and right bass frequen- cies under the crossover frequency selected in another setting on this menu, as described below, and also the LFE soundtrack.

9.When all initial speaker “size” settings have been made, you now have the option to take advantage of the AVR’s Quadruple Crossover system, which allows individual crossover settings to be made for each speaker grouping set to "Small". The low-fre- quency crossover point is set by the design of your speakers. It is defined as the frequency which is the lowest possible frequency the speaker is capable of reproducing. Before making any changes to the set- tings for the crossover point we suggest that you find the crossover point for the speakers in each of the four groupings, front left/right, center, surround and surround back by looking at the specifications page of the speaker’s owner’s manual, by getting that information from the manufacturer’s Web site, or by contacting your dealer or the manufacturer’s customer service department. You will need this fig- ure to accurately configure the next group of set- tings.

The factory default setting for all speaker positions is 100Hz. If that setting is acceptable for all channels, then no adjustments are needed and you may skip this section. However, should you wish to change one of the settings, please proceed by pressing the

⁄Button Eso that the cursor moves back up to the top of the list of setting options. Press the ‹/ › Buttons Eso that X-OVERis highlighted and the menu data will change to the screen shown in Figure 5.


* * S P E A K E R S E T U P				* *

M O D E	: S I Z E		X - O V E R
L E F T / R I G H T :		1 0 0 H Z
C E N T E R	:	1 0 0 H Z
S U R R O U N D	:	1 0 0 H Z
S U R R B A C K :		1 0 0 H Z
L F E	: L E F T / R I G H T
B A S S M G R	:	G L O B A L

B A C K T O M A S T E R M E N U

Figure 5

To change the setting for any of the four speaker groups Left/Right, Center, Surrounds or Surround Back, press the ⁄/¤ Buttons Euntil the cur- sor is next to the line where you wish to make a change and then press the ‹/› Buttons E until the desired setting appears. The available choices at which point low-frequency information will be sent to the subwoofer (or to the Front Left/Right speakers in case subwoofer is set to OFF), rather than to the speaker channel, are 40Hz, 60Hz, 80Hz, 100Hz, 120Hz and 200Hz. Pick the choice that is identical to the information

24SYSTEM CONFIGURATION

for the speakers, or if an exact match is not possi- ble, pick the closest choice that is ABOVE the speaker’s lowfrequency limit to avoid the creation of a low-frequency “hole” where your system will have no bass information.

In cases where LARGE has been selected as the front channel speaker option and LFE+L/R has been selected as the subwoofer option, the front channel sound information below the cross- over point selected for the L/R front speakers (when fronts are set to "Small") will be sent to BOTH the front channel speakers and the sub- woofer.

When all speakers are set to LARGE the crossover point for the fronts (selectable when they are set to "Small") will affect the LFE signal and the bass support for the front speakers by the sub (when the sub is set to L/R+LFE, see above) only. In that case the default value "100Hz" should be kept or selected for the crossover point for the L/R fronts (selectable when they are "Small") as it´s indicated (and marked by *) behind the LEFT/RIGHT line in the speaker setup menu when the X-OVER option is selected.

10.When all speaker selections have been made, press the ¤ Button Euntil the cursor is next to the BACK TO MASTER MENU line and press the Set Button Fto return to the Main menu.

11.The Speaker Configuration may also be changed at any time without using the full-OSD on-screen menu system by pressing the Speaker

Selector 6 on the front panel or on the remote control. Once the button is pressed, FRONT SPEAKER will appear in both the lower third of the video display and the Main Information Display ˜.

Within five seconds, either press the ‹/› buttons 7 $ on the front panel or the ⁄/¤ buttons

Eon the remote to select a different speaker position, or press the Set Button @F to begin the adjustment process for the front left and right speakers.

When the Set button @ Fhas been pressed and the system is ready for a change to the front speaker setting, the on-screen display and Main Information Display ˜ will read FRONT LARGE or FRONT SMALL depending on the current setting. Press the ‹/› buttons 7 $ on the front panel or the ⁄/¤ buttons Eon the remote until the desired setting is shown, using the instructions for “large” or “small” shown earlier, then press the Set button @F.

If another speaker position needs to be changed, press the ‹/› buttons 7 $ on the front panel or the ⁄/¤ buttons Eon the remote to select a different speaker position, press the Set button

@Fand then the ‹/› buttons 7 $ on the front panel or the ⁄/¤ buttons Eon the remote until the correct speaker setting is shown

and press the Set button @ Fagain to con- firm the selection.

To assist in making these settings, the icons in the Speaker/Channel Input Indicators Ú will change as the speaker type is selected at each position. When only the inner icon box is lit, the speaker is set for “small.” When the inner box and the two outer boxes with circles inside them are lit, the speaker is set for “large." When no indica- tor appears at a speaker location, that position is set for “none” or “no” speaker.

Note: These icons are available only when making setup changes without the use of the full OSD mode.

As an example, in the Figure below, all speakers are set for “large,” and a subwoofer is set.

Surround Setup

Once the speaker setup has been completed, the next step for that input is to set the surround mode you wish to use with that input. Since sur- round modes are a matter of personal taste, feel free to select any mode you wish – you may change it later. The Surround Mode chart on page 29 may help you select the mode best suited to the input source selected. For example you may select Dolby Pro Logic II or Logic 7 for most ana- log inputs and Dolby Digital for inputs connected to digital sources. In the case of inputs such as a CD Player, Tape Deck or Tuner, you may wish to set the mode to Stereo, if that is your preferred listen- ing mode for standard stereo sources, where it is unlikely that surround encoded material will be used. Alternatively, the 5 Channel Stereo or Logic 7 Music mode may also be a good choice for stereo-only source material.

It is easiest to complete the surround setup using the full-OSDon-screen menus. From the MASTER menu (Figure 1), press the ⁄/¤ but- tons Euntil the › cursor is next to the SURROUND SELECT menu. Press the Set Button Fso that the SURROUND SELECT menu (Figure 6) is on the screen.