Programming the Remote
7.The next display (Figure 42) and the subse- quent screens are where the actual macro programming take place. The words at the left side of the top line of the display show the button that is being programmed (e.g., the Power On Button 3or one of the Macro
Buttons ) and the indication at the right side of the top line shows the number of macro steps available of 20 possible steps. Following the instructions on the remote’s LCD screen, press the first key you wish to be transmitted in the macro. In our example, we first want the AVR to turn on, so the Power Button 3should be pressed.
P O W E R O N | 0 0 / 2 0 |
S E L E C T K E Y P R E S S
Figure 42
8.Once the first command button for the macro has been pressed, continue to press the but- tons you wish to be part of the macro, in the order they will be used. Press each button within five seconds of the last button, remem- bering to press the Input Selector 45 when you are changing device functions.
As the buttons on the remote are pressed, the remote’s display screen will show the steps in the macro as they are programmed (Figure 43).
[ A V R ]
[ A V R ] P O W E R O N
Figure 43
9.For our example, we first want the AVR Power On button pressed, followed by the TV Power On, followed by the Cable Box On, followed by the selection of the Logic 7 mode. To do that, press the buttons in this order:
•Power On 3
•VID 2/TV 4
•Power On 3
•VID 3/Cable 4
•Power On 3
•AVR 5
•Logic 7 O
As each button is pressed to enter it into the macro you will see the button names appear and then scroll up on the LCD display as your confirmation of the key entry (Figure 43).
10.When all commands for the macro have been entered, press the Set Button Fto save the macro. The display screen will show the button to which the macro has been pro- grammed and the number of steps used, and the word SAVED will blink four times in the lower line of the LCD display. When the dis- play returns to normal, the macro has been entered and the remote is ready for opera- tion.
11.If a macro has been programmed into the Power On Button 3, it will play back anytime the Power On button is pressed. As the macro plays, you will see the steps
appear in the remote’s LCD display. Macros programmed into one of the four discrete Macro buttons may be activated at any time by pressing the appropriate button.
Erasing a Macro
Once a macro has been created and stored in the AVR remote’s memory, you have the option of erasing it. You may do this at any time by fol- lowing these steps:
1. Press and hold the Program Button for about three seconds while the message shown in Figure 15 appears in the remote’s LCD Information Display 2. Release the button when the red light under the Set Button Fappears.
2.The remote’s MAIN MENU message (Figure 16), will appear in the LCD display and the Set Button Fwill remain illuminated in red. Press the ⁄ Navigation Buttons E three times so that MACRO appears on the bottom line of the LCD screen, as shown in Figure 37. Press the Set Button Fto enter the main macro menu branch.
3.At the next menu screen (Figure 44) press
⁄¤ Navigation Buttons Euntil the bottom line in the remote’s LCD display reads ERASE A MACRO, as shown in Figure 44. Press the Set Button Fto begin the process of erasing a macro.
M A C R O
E R A S E A M A C R O
Figure 44
4.The next display screen (Figure 45) is where you select which macro will be erased. Press the ⁄¤ Navigation Buttons Euntil the number of the macro you wish to erase appears. For this example we will erase the Power On macro created in the previous sec- tion. When the name of the macro to be erased appears, press the Set Button F.
E R A S E A M A C R O
P O W E R O N
Figure 45
5.The word ERASED will flash four times in the bottom line of the remote’s LCD display, and then the display will return to its normal con- dition. When that happens the macro is erased and the remote is returned to normal operation.
Read a Macro
To check the commands stored in the remote’s memory for one of the buttons, follow these steps:
1. Press and hold the Program Button | for |
about three seconds while the message |
|
shown in Figure 15 appears in the remote’s LCD Information Display 2. Release the button when the red light under the Set Button Fappears.
2.The remote’s MAIN MENU message (Figure 16), will appear in the LCD display and the Set Button Fwill remain illuminated in red. Press the ⁄ Navigation Buttons E three times so that MACRO appears on the bottom line of the LCD screen, as shown in Figure 37. Press the Set Button Fto enter the main macro menu branch.
3.At the next menu screen (Figure 46) press the
⁄¤ Navigation Buttons Euntil the bottom line in the remote’s LCD display shows READ A MACRO, as shown in Figure 46. Press the Set Button Fto begin the process of erasing a macro.
M A C R O
R E A D A M A C R O
Figure 46
4.The next display screen (Figure 47) is where you select the macro to be read. Press the
⁄¤ Navigation Buttons Euntil the name of the macro you wish to read appears. For this example, we will read back the Power On macro created in the previous section. When the name of the macro to be erased appears, press the Set Button F.
R E A D A M A C R O
P O W E R O N
Figure 47
5.As soon as the Set button is pressed, the first two steps in the macro will be appear in the remote’s LCD screen. You may then use the
⁄¤ Navigation Buttons Eto step up or down through the list of commands stored as the macro. As you read the display, you will see Device Selector Buttons 45 appear in brackets, (e.g., [AVR]). When the step in the macro is a function, navigation or any other button, it will appear next to the bracketed
6.When you are finished reviewing the macro’s contents, press the Set Button Fto return the remote to normal operation.
Punch-Through Configuration
46PROGRAMMING THE REMOTE