Harman-Kardon AVR 3550HD owner manual Selecting a Surround Mode

Page 38

OPERATION

Figure 62 – The Bridge

Press the Menu Button to view the slide-out menu:

Back: Returns to the previous screen. This option appears while navigating the contents of the iPod.

Music: Navigates the audio materials stored on the iPod.

Photos: Select this line to view still images stored on a photo-capable iPod. The system will switch to iPod Manual Mode, and control will shift to the iPod. Use the screen and controls on the iPod. The AVR remote may also be used.

To view photos on a video monitor connected to the AVR, select the photo and press the Play Button on the iPod itself, or press the OK Button on the remote three times.

Videos: Select this line to view videos stored on an iPod that supports video browsing.

NOTES ON VIDEO PLAYBACK:

As of this writing, video browsing is only supported on the iPod 5G, iPod classic (80GB, 120GB and 160GB), iPod nano 3G and 4G, and iPod touch (when loaded with software version 2 or higher). For other iPod models, it is not possible to view photos (except iPod 4G) or videos on an external monitor while using The Bridge II. However, you may purchase a com- patible A/V cable from Apple Inc. that has a dock connector on one end and conventional audio and video plugs on the other end. The audio/video plugs may be connected to any available analog inputs on the AVR.

Before attempting to view photos or videos stored on your iPod, check the Video Settings menu on the iPod and make sure that the TV Out setting is set to On. The TV Signal setting should be NTSC to match the capabilities of your video display. If your selection was playing and paused, the iPod requires you to reselect the video for the new TV Out setting to take effect.

To exit iPod Manual Mode, with the AVR remote in The Bridge mode, press and hold the Menu Button.

Random: Select this setting for random playback, also known as “Shuffle Mode”. Each press of the OK Button switches the setting: shuffle by Song, shuffle by Album, or Off to end random playback.

Repeat: Select this setting to repeat a track or all tracks in the current album or play list. Each press of the OK Button switches the setting: repeat Off, repeat One or repeat All.

NOTE: The iTunes application allows you to exempt some tracks from Shuffle mode. The AVR 3550HD cannot override this setting.

Table 2 summarizes the controls available with The Bridge II.

Table 2 – Using The Bridge II

 

iPod Function

Remote Control Key

 

 

 

 

 

 

Play

Play ( )

 

 

 

 

 

 

Pause

Pause ( II )

 

 

 

 

 

 

Menu

Menu

 

 

 

 

 

 

Select

OK

 

 

 

 

 

 

Scroll Reverse

Left Arrow ()

 

 

 

 

 

 

Scroll Forward

Right Arrow ( )

 

 

Forward Search/Next Track

Forward/Next ( ››)

 

 

 

 

 

 

Reverse Search/Previous Track

Reverse/Previous (‹‹ )

 

 

 

 

 

 

Page Up/Down

Channel/Page Up/Down

 

 

 

 

 

While scrolling, hold the key to scroll faster. Use the Page Up/Down control on the remote to scroll a page at a time.

NOTES:

The Play and Pause functions are not available unless content has been selected for playback.

To search within a track, press and hold the indicated button. Press the Previous Track Button once to skip to the beginning of the current track. Press the Previous Track Button twice to skip to the beginning of the previous track.

While a selection is playing, the song title, artist and album name will appear in the upper line in the front-panel Message Display. The lower line will display the elapsed time of the track on the left, the play mode icon, and the time remaining on the right.

If a video monitor is connected to the AVR 3550HD and the system is not in iPod Manual Mode, it will display the play mode icon, song title, artist and album. A graphic bar indicates the current play position within the track. If random or repeat play has been programmed, an icon will appear in the upper right corner.

The screen may disappear from view, depending on the Setup and Slide-In Menus setting in the System Settings menu (described in the Advanced Functions section). Restore the Now Playing screen to view by pressing either of the / Buttons.

NOTE: It is strongly recommended that you use a screen saver built into your video display to avoid possible damage from “burn-in” that may occur with plasma and many CRT displays when a still image, such as a menu screen, remains on display for an extended period of time.

Selecting a Surround Mode

Surround mode selection can be as simple or sophisticated as your individual system and tastes. Feel free to experiment, and you may find a few favorites for certain sources or program types. More detailed

38

38

Image 38
Contents AVR 3550HD Safety Information Important Safety InstructionsImportant Safety Information Do not place the unit directly on a carpeted surfaceTable of Contents Thank you for choosing a Harman Kardon product IntroductionHarman Kardon AVR 3550HD 7.1-Channel Audio/Video Receiver Audio SectionAudio/Video Inputs Supplied AccessoriesAudio Inputs Digital Audio InputsFRONT-PANEL Controls Volume Knob Turn this knob to raise or lower the volume Power Indicator This LED has three possible modesOn When the AVR is turned on, this LED turns white REAR-PANEL Connections REAR-PANEL Connections REAR-PANEL Connections Main Remote Control Functions Main Remote Control Functions Main Remote Control Functions Zone 2 Remote Control Functions Zone 2 Remote Control Functions Typical Home Theater System Introduction to Home TheaterSurround Modes Multichannel AudioSpeaker Connections Connecting Source Devices to the AVRConnections SubwooferAnalog Video Video ConnectionsDigital Video Hdmi cable runs are limited to about 10 feetRS-232 Serial Port FM antenna uses a 75-ohm F-connector. See FigureAntennas Placement of Surround Speakers in a 5.1-Channel System Speaker PlacementFront Speaker Placement Placement of Surround Speakers in a 7.1-Channel SystemStep Two Connect the Subwoofer InstallationStep One Connect the Speakers Step Three Connect the AntennasChoose one digital audio connection Optical or Coaxial Audio Connections for non-HDMI sourcesVideo Connections for non-HDMI sources Hdmi Video Connect the player as shown in FigureConnect an Audio/Video Recorder PVD, DVR or TiVo Hdmi Video Connect the recorder as shown in FigureConnect a CD Player or Any Audio-Only Device Connect an iPod Using Docking StationConnecting a Game Console, Camera or Other Device Connect a Tape Deck or Any Audio-Only RecorderStep Six Plug in AC Power Step Five Connect the Video DisplaySatisfactory code set that operates most functions Step Seven Insert Batteries in RemoteEnter a code from , above Step Ten Install a Multizone System Optional LearningStep Eleven Turn On the AVR 3550HD Zone 2 Audio OutputsAVR Power On and Source Selectors Configure the AVR 3550HD Using EzSet/EQ Technology Initial SetupUsing the On-Screen Menu System Set Up Sources Select Cancel to return to the Speaker Setup menuHDMI-Equipped Multichannel Disc Player Audio and Video Input SelectionChannel Direct Inputs ‹ / › Buttons to delay the audio by up to 180ms. See Figure You are now ready to begin enjoying your new receiverOperation XM Radio Operation Using the TunerSource Selection Press the OK Button to store the new preset Using Docking StationTo store a channel in one of the 40 preset locations RecordingMusic Navigates the audio materials stored on the iPod Selecting a Surround ModePress the Menu Button to view the slide-out menu CH Stereo plays the left-channel signal through the front Auto SELECT, Surr VIRTUAL, Surr STEREO, Surr MOVIE, SurrAdvanced Functions Analog Audio SignalsDigital Audio Signals Audio Processing and Surround SoundDolby Surround Settings Indicates that no surround information is presentNight Mode Manual SetupStep Three Manual Setup Menu Step Two Measure Speaker DistancesNumber of Speakers Adjust Crossover Frequencies MenuSub Mode Step Four Setting Channel Output Levels Manually Adjust Speaker Distance MenuVideo Adjustments Tone Control Determines whether the treble and bassNature For programs shot outdoors, in a natural setting How to Adjust the Custom Picture SettingsBrightness Adjustment Sports For sporting eventsMultizone Operation Operating the Multizone System System SettingsGeneral AVR Settings Menu AppearancePunch-Through Programming Advanced Remote Control FunctionsResetting the Remote Activities MacrosProcessor Reset MemoryTroubleshooting Guide Appendix Appendix Default settings, worksheets, remote product codesTable A2 Source Setting Defaults Table A1 Recommended Source Component ConnectionsTable A3 Speaker/Channel Setting Defaults Table A4 Delay Setting DefaultsTable A7 Video Modes Settings Table A5 Source SettingsTable A6 Audio Effects Settings Table A8 Surround Modes Table A9 Remote Control CodesTable A10 System Settings Table A11 Zone 2 Settings Table A12 Surround ModesMovie Back channel 0 or .1, EX Analog 2-channel Tuner Mode Group Enveloping sound field is desiredExperience Tuner Music adds a surround back channel Analog 2-channel TunerPerformance Via Hdmi DTS-ES Matrix Surround Mode Description Incoming Bitstream or SignalRate used on DVD-Video discs DTS StereoChannels Tuner PCM 32kHz, 44.1kHz or 48kHz Channel Stereo Appropriate when a subwoofer is usedChannel Stereo Analog Bypass41 42 DMC1000 Table A13 Remote Control Function ListRadio Button Name Power OffTable A13 GameAiwa Table A14 Table A16 Remote Control Product Codes AUX-VCRTable A15 Remote Control Product Codes AUX-HDTV Table A16Table A18 Remote Control Product Codes DVD Table A17Table A21 Remote Control Product Codes CBL Table A19 Remote Control Product Codes SATTable A20 Remote Control Product Codes Game Table A24 Remote Control Product Codes AUX- TiVo Table A22 Remote Control Product CodesTable A23 Remote Control Product Codes Table A21Product Shipping Weight 31.5 lb 14.3kg 36.7 lb 16.7kg General Power Requirement AC 120V/60Hz Power ConsumptionChannels driven Dimensions Product Shipping Width Linear High-Level 200mV/47k ohms