Harman-Kardon AVR 3550HD owner manual Important Safety Information

Page 3

SAFETY INFORMATION

Important Safety Information

Verify Line Voltage Before Use

Your AVR 3550HD has been designed for use with 120-volt AC current. Connection to a line voltage other than that for which it is intended can create a safety and fire hazard and may damage the unit.

If you have any questions about the voltage requirements for your specific model, or about the line voltage in your area, contact your selling dealer before plugging the unit into a wall outlet.

Do Not Use Extension Cords

To avoid safety hazards, use only the power cord attached to your unit. We do not recommend that extension cords be used with this product. As with all electrical devices, do not run power cords under rugs or carpets or place heavy objects on them. Damaged power cords should be replaced immediately by an authorized service center with a cord meeting factory specifications.

unit’s feet may leave marks on certain wood or veneer materials. Use caution when placing the unit on soft woods or other materials that may be damaged by heat or heavy objects. Some surface finishes may be particularly sensitive to absorbing such marks, due to a variety of factors beyond our control, including the nature of the finish, cleaning materials used, and normal heat and vibration caused by the use of the product, or other factors. We recommend that caution be exercised in choosing an installation location for the component and in normal maintenance practices, as your warranty will not cover this type of damage to furniture.

Cleaning

When the unit gets dirty, wipe it with a clean, soft, dry cloth. If necessary, and only after unplugging the AC power cord, wipe it with a soft cloth dampened with mild soapy water, then a fresh cloth with clean water. Wipe it dry immediately with a dry cloth. NEVER use benzene, aerosol cleaners, thinner, alcohol or any other volatile cleaning agent. Do not use abrasive cleaners, as they may damage the finish of metal parts. Avoid spraying insecticide near the unit.

Handle the AC Power Cord Gently

When disconnecting the power cord from an AC outlet, always pull the plug; never pull the cord. If you do not intend to use the unit for any considerable length of time, disconnect the plug from the AC outlet.

Do Not Open the Cabinet

There are no user-serviceable components inside this product. Opening the cabinet may present a shock hazard, and any modification to the product will void your guarantee. If water or any metal object such as a paper clip, wire or staple acciden- tally falls inside the unit, disconnect it from the AC power source immediately, and consult an authorized service center.

CATV or Antenna Grounding

If an outside antenna or cable system is connected to this product, be certain that it is grounded so as to provide some protection against voltage surges and static charges. Section 810 of the National Electrical Code, ANSI/NFPA No. 70-1984, provides information with respect to proper grounding of the mast and supporting structure, grounding of the lead-in wire to an antenna discharge unit, size of grounding conduc- tors, location of antenna discharge unit, connection to grounding electrodes and requirements of the grounding electrode.

NOTE TO CATV SYSTEM INSTALLER: This reminder is provided to call the CATV (cable TV) system installer’s attention to article 820-40 of the NEC, which provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of cable entry as possible.

Installation Location

To ensure proper operation and to avoid the potential for safety hazards, place the unit on a firm and level surface. When placing the unit on a shelf, be certain that the shelf and any mounting hardware can support the weight of the product.

Make certain that proper space is provided both above and below the unit for ventilation. If this product will be installed in a cabinet or other enclosed area, make certain that there is sufficient air movement within the cabinet. Under some circumstances, a fan may be required.

Do not place the unit directly on a carpeted surface.

Avoid installation in extremely hot or cold locations, or in an area that is exposed to direct sunlight or heating equipment.

Avoid moist or humid locations.

Do not obstruct the ventilation slots on the top of the unit, or place objects directly over them.

Due to the weight of the AVR 3550HD and the heat generated by the amplifiers, there is the remote possibility that the rubber padding on the bottom of the

Moving the Unit

Before moving the unit, be certain to disconnect any interconnection cords with other components, and make certain that you disconnect the unit from the AC outlet.

Important Information for the User

This equipment has been tested and found to comply with the limits for a Class-B digital device, pursuant to Part 15 of the FCC Rules. The limits are designed to pro- vide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio-frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interfer- ence to radio communication. However, there is no guarantee that harmful interfer- ence will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

Consult the dealer or an experienced radio/TV technician for help.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and

(2)this device must accept interference received, including interference that may cause undesired operation.

NOTE: Changes or modifications may cause this unit to fail to comply with Part 15 of the FCC Rules and may void the user’s authority to operate the equipment.

Unpacking

The carton and shipping materials used to protect your new receiver during ship- ment were specially designed to cushion it from shock and vibration. We suggest that you save the carton and packing materials for use in shipping if you move, or should the unit ever need repair.

To minimize the size of the carton in storage, you may wish to flatten it. This is done by carefully slitting the tape seams on the bottom and collapsing the carton. Other card- board inserts may be stored in the same manner. Packing materials that cannot be col- lapsed should be saved along with the carton in a plastic bag.

If you do not wish to save the packaging materials, please note that the carton and other sections of the shipping protection are recyclable. Please respect the environ- ment and discard those materials at a local recycling center.

It is important that you remove the protective plastic film from the front-panel lens. Leaving the film in place will affect the performance of your remote control.

3

Image 3
Contents AVR 3550HD Important Safety Instructions Safety InformationDo not place the unit directly on a carpeted surface Important Safety InformationTable of Contents Audio Section IntroductionHarman Kardon AVR 3550HD 7.1-Channel Audio/Video Receiver Thank you for choosing a Harman Kardon productDigital Audio Inputs Supplied AccessoriesAudio Inputs Audio/Video InputsFRONT-PANEL Controls Power Indicator This LED has three possible modes On When the AVR is turned on, this LED turns whiteVolume Knob Turn this knob to raise or lower the volume REAR-PANEL Connections REAR-PANEL Connections REAR-PANEL Connections Main Remote Control Functions Main Remote Control Functions Main Remote Control Functions Zone 2 Remote Control Functions Zone 2 Remote Control Functions Multichannel Audio Introduction to Home TheaterSurround Modes Typical Home Theater SystemSubwoofer Connecting Source Devices to the AVRConnections Speaker ConnectionsHdmi cable runs are limited to about 10 feet Video ConnectionsDigital Video Analog VideoFM antenna uses a 75-ohm F-connector. See Figure AntennasRS-232 Serial Port Placement of Surround Speakers in a 7.1-Channel System Speaker PlacementFront Speaker Placement Placement of Surround Speakers in a 5.1-Channel SystemStep Three Connect the Antennas InstallationStep One Connect the Speakers Step Two Connect the SubwooferHdmi Video Connect the player as shown in Figure Audio Connections for non-HDMI sourcesVideo Connections for non-HDMI sources Choose one digital audio connection Optical or CoaxialHdmi Video Connect the recorder as shown in Figure Connect an Audio/Video Recorder PVD, DVR or TiVoConnect a Tape Deck or Any Audio-Only Recorder Connect an iPod Using Docking StationConnecting a Game Console, Camera or Other Device Connect a CD Player or Any Audio-Only DeviceStep Five Connect the Video Display Step Six Plug in AC PowerStep Seven Insert Batteries in Remote Enter a code from , aboveSatisfactory code set that operates most functions Learning Step Ten Install a Multizone System OptionalZone 2 Audio Outputs Step Eleven Turn On the AVR 3550HDAVR Power On and Source Selectors Initial Setup Using the On-Screen Menu SystemConfigure the AVR 3550HD Using EzSet/EQ Technology Select Cancel to return to the Speaker Setup menu Set Up SourcesAudio and Video Input Selection Channel Direct InputsHDMI-Equipped Multichannel Disc Player You are now ready to begin enjoying your new receiver ‹ / › Buttons to delay the audio by up to 180ms. See FigureOperation Using the Tuner Source SelectionXM Radio Operation Recording Using Docking StationTo store a channel in one of the 40 preset locations Press the OK Button to store the new presetSelecting a Surround Mode Press the Menu Button to view the slide-out menuMusic Navigates the audio materials stored on the iPod Auto SELECT, Surr VIRTUAL, Surr STEREO, Surr MOVIE, Surr CH Stereo plays the left-channel signal through the frontAudio Processing and Surround Sound Analog Audio SignalsDigital Audio Signals Advanced FunctionsIndicates that no surround information is present Dolby Surround SettingsStep Two Measure Speaker Distances Manual SetupStep Three Manual Setup Menu Night ModeAdjust Crossover Frequencies Menu Sub ModeNumber of Speakers Adjust Speaker Distance Menu Step Four Setting Channel Output Levels ManuallyTone Control Determines whether the treble and bass Video AdjustmentsSports For sporting events How to Adjust the Custom Picture SettingsBrightness Adjustment Nature For programs shot outdoors, in a natural settingMultizone Operation Menu Appearance System SettingsGeneral AVR Settings Operating the Multizone SystemActivities Macros Advanced Remote Control FunctionsResetting the Remote Punch-Through ProgrammingMemory Processor ResetTroubleshooting Guide Table A1 Recommended Source Component Connections Appendix Default settings, worksheets, remote product codesTable A2 Source Setting Defaults AppendixTable A4 Delay Setting Defaults Table A3 Speaker/Channel Setting DefaultsTable A5 Source Settings Table A6 Audio Effects SettingsTable A7 Video Modes Settings Table A9 Remote Control Codes Table A10 System SettingsTable A8 Surround Modes Table A12 Surround Modes Table A11 Zone 2 SettingsMusic adds a surround back channel Analog 2-channel Tuner Mode Group Enveloping sound field is desiredExperience Tuner Movie Back channel 0 or .1, EX Analog 2-channel TunerDTS Stereo Surround Mode Description Incoming Bitstream or SignalRate used on DVD-Video discs Performance Via Hdmi DTS-ES MatrixAnalog Bypass Appropriate when a subwoofer is usedChannel Stereo Channels Tuner PCM 32kHz, 44.1kHz or 48kHz Channel Stereo41 42 Table A13 Remote Control Function List RadioDMC1000 Game Power OffTable A13 Button NameAiwa Table A16 Table A16 Remote Control Product Codes AUX-VCRTable A15 Remote Control Product Codes AUX-HDTV Table A14Table A17 Table A18 Remote Control Product Codes DVDTable A19 Remote Control Product Codes SAT Table A20 Remote Control Product Codes GameTable A21 Remote Control Product Codes CBL Table A21 Table A22 Remote Control Product CodesTable A23 Remote Control Product Codes Table A24 Remote Control Product Codes AUX- TiVoLinear High-Level 200mV/47k ohms General Power Requirement AC 120V/60Hz Power ConsumptionChannels driven Dimensions Product Shipping Width Product Shipping Weight 31.5 lb 14.3kg 36.7 lb 16.7kg