Nilfisk-ALTO 571 How to Operate the Forward / Reverse Switch see figure, Operating the Machine

Page 19

How To Operate the Machine

How to Operate the Forward / Reverse Switch (see figure 28).

1.To go forward, push the up arrow side of the switch.

2.To go in reverse, push the down arrow side of the switch.

How to Fill the Solution Tank

The solution tank fill port is located at the left side of the machine (see figure

29). To fill the solution tank, follow this procedure:

1.Turn the key switch to the “OFF” position.

2.Remove lid.

3.Add a cleaning chemical to the solution tank. For the correct amount of chemical, follow the directions shown on the container. NOTE:

Excess foam in the recovery tank could damage the vacuum motor, so use only the minimum amount of detergent necessary.

WARNING: Always use low foam detergent. To avoid the production of foam, before starting to clean, put a minimum quantity of antifoam liquid into the recov- ery tank. NEVER USE PURE ACID.

4.Fill the solution tank with clean water (see figure 29).

5.After filling the solution tank, replace the solution tank lid.

WARNING: Water solutions or cleaning materials used with this type of machine can leave wet areas on the floor surface. These areas can cause a dangerous condi- tion for the operator or other persons. Always put CAUTION signs near the area you are cleaning.

WARNING: Machines can ignite flammable materials and vapors. Do not use with or near flammables such as gasoline, grain dust, solvents and thinners. Only use a cleaning concentration recommended by the chemical manufacturer.

WARNING: Nilfisk ALTO recommends a maximum water tem- perature of 120°F (49°C).

Operating the Machine

NOTE: Before scrubbing with the machine, become familiar with the opera- tions and handling of the machine. Run the machine at the lowest traverse speed. Use the machine in an area that has no furniture or objects until you can do the following:

1.Traverse the machine in a straight direction, forward and backward.

2.Stop the machine safely.

3.Turn the machine both left and right and return to a straight direction.

4.Turn a 180o turn where one rear wheel just pivots.

Figure 28

Figure 29

Nilfisk ALTO Operator’s Manual - SCRUBTEC R Manual Steering

Form No. 71274A

Page -19-

Page 18 Page 20
Image 19
Page 18 Page 20
Contents 30-72 English Instructions For UseTable of Contents Operator Safety Instructions Nilfisk Alto Operator’s Manual Scrubtec R Manual Steering Introduction & Machine Specifications IntroductionSymbols Used On Scrubtec R Display Screens For Scrubtec R Machine Control Panel Machine Controls and Features How to Install the Batteries How To Prepare the Machine For OperationHow To Handle the Packed Machine How to Unpack the MachineCorrect Fill Battery MaintenanceShown with Optional Chemical Mixing Sytem How to Charge the BatteriesRecharging the Batteries How To Install the Squeegee Level Indicators for the Charge of the BatteriesHow To Change or Rotate Brushes on Cylindrical Brush Head How To Remove The Brush Or Pad on the Boost machine How To Install The Brush Or Pad on the Boost machineSeat Adjustment Deluxe How To Operate The MachineScreen How to Read the Battery Meter see figure 21, aHow to Operate the Solution Flow How to Operate the Squeegee and the Vacuum MotorHow to Operate the Brush Pressure How to Fill the Solution Tank How to Operate the Forward / Reverse Switch see figureOperating the Machine Do These Procedures When You Begin Your Work Period To traverse the machine follow this procedureHow to Clean a Floor Do These Procedures When You End Your Work Period How to Clean a Very Dirty FloorHow To Operate the Machine Cleaning the Recovery Tank and Filter MaintenanceSqueegee Maintenance Cleaning the Solution Tank and FilterManually Draining the Solution Tank Vac Assisted Solution Tank DrainCleaning the Vacuum Hoses Rear Squeegee Blade ReplacementHOW to Correct Problems in the Machine Cause Action Cause Action Scrubtec R Scrubtec R 571 C Final Assembly Qty Description Rotary Cyl Boost See Detail a Ref. No Qty Description See Detail a Main Frame Assy Cylindrical Main Frame Assy Boost Main Frame Assy Boost Nilfisk Alto Scrubtec R 571 Description Qty Optional Side Squeegee Lift Assembly Parts List 5/05Nilfisk Alto Scrubtec R 571, 586, 571 C, Boost R 1611 2514 Recovery Tank Assembly Nut, Drain Valve 44 31 Solution Tank ASSEMBLY-1 Solution Tank ASSEMBLY-2 Solution Tank ASSEMBLY-2 Steering Column Assy Steering Column Assy Nilfisk Alto 1A, 1B, 1C1A, 1B, 1C 20 19 18 17 AssembledView Cylindrical Head Assembly Parts List 1/11 Drawing #10962A Inch Boost Head Assy Kit-Flex Plate 32 Note 1, TSBCL2010-12 Shield Boost Bearing Note 1, TSBCL2010-12, NoteBushing-Flex Plate Note 1, TSBCL2010-12 Squeegee Assembly 81cm Squeegee Assembly 81cm Squeegee Assembly 99cm Squeegee Assembly 99cm Squeegee Assembly 104cm Squeegee Assembly 104cm Qty Description Front Squeegee Assy Rotary Machines onlyFront Squeegee ARM Assy Rotary Machines only Nilfisk Alto Scrubtec R 571, 586, 571 C, Boost R Qty Description Pages Electrical Connection Diagram 9/06Nilfisk Alto -68- Form No a Page Nilfisk Alto Operator’s Manual Scrubtec R Manual Steering Page Scrubtec R 571 C Cylindrical Model Scrubtec R 571 Disc ModelDeleted Scrubtec R 586 Disc ModelPage Page
Related manuals
Manual 72 pages 47.09 Kb

586, 571 specifications

Nilfisk-ALTO has long been recognized for its commitment to delivering high-quality cleaning solutions, and the Nilfisk-ALTO 586, 571, R 571 C, SCRUBTEC R 586, and SCRUBTEC R 571 models exemplify this dedication. These compact and efficient scrubbers are designed for effective cleaning in various environments, making them suitable for both industrial and commercial applications.

The Nilfisk-ALTO 586 and SCRUBTEC R 586 models feature advanced scrubbing technology, providing users with exceptional cleaning results. They are equipped with a highly efficient brush system that can adapt to different floor surfaces, ensuring optimal cleaning performance whether in retail spaces, warehouses, or manufacturing facilities. The unique brush design simplifies the replacement process, allowing operators to switch brushes quickly and easily.

Among their key characteristics is the ability to adjust the water flow and detergent dose to suit the specific cleaning requirements. This contributes to sustainability, as it minimizes water and detergent waste while maximizing cleaning efficacy. Additionally, their ergonomic design promotes user comfort during operation, reducing fatigue during extended cleaning tasks.

The SCRUBTEC R 571 and R 571 C models bring technological advancements, including a patented electronic control system that manages all aspects of the cleaning process. This system allows users to monitor performance metrics in real-time, providing valuable insights into efficiency and usage patterns. Integrated with a large capacity solution tank, these machines can sustain longer cleaning cycles without frequent refills, making them ideal for larger areas.

Another notable feature is the ultra-compact design of these models, which facilitates maneuverability in tight spaces. Their low profile and slim design allow operators to access hard-to-reach areas, ensuring comprehensive cleaning results. Furthermore, the machines are equipped with advanced noise reduction technology, making them suitable for use in noise-sensitive environments.

Overall, the Nilfisk-ALTO 586, 571, R 571 C, SCRUBTEC R 586, and SCRUBTEC R 571 smoothie’s state-of-the-art features and technologies offer exceptional cleaning efficiency. Their operational flexibility, coupled with user-friendly controls, positions them as an ideal choice for businesses looking to invest in reliable and effective floor cleaning solutions. With Nilfisk-ALTO, users can count on superior performance and durability built into every model.
Top Page Image Contents