Nilfisk-ALTO 586, 571 manual Nilfisk Alto Operator’s Manual Scrubtec R Manual Steering

Page 4

WARNING: Any alterations or modifications of this machine could result in damage to the machine or injury to the operator or other bystand- ers. Alterations or modifications not authorized by the manufacturer voids any and all warranties and liabilities.

WARNING: Electrical components of this machine can “short-out” if exposed to water or moisture. Keep the electrical components of the machine dry. Wipe the machine down after each use. This appliance is for dry use only and is not to be used or stored outdoors in wet conditions. For storage, keep the machine in a building.

WARNING: Operating a machine without observing all labels and instructional information could result in injury or damage. Read all machine labels before attempting to operate. Make sure all of the labels and instructional information are attached or fastened to the machine. Do not cover them for any reason. If labels or decals are missing or become damaged, get replacement labels and decals from your Nilfisk ALTO distributor immediately.

WARNING: Wet floor surfaces can be slippery. Water solutions or cleaning materials used with this type of machine can leave wet areas on the floor surface. These areas can cause a dangerous condition for the operator or other persons. Always put “Caution” signs around/near the area you are cleaning.

WARNING: Improper discharge of waste water may damage the environment and be illegal.

The United States Environmental Protection Agency has established certain regulations regarding discharge of waste water. City, state and national regulations regarding this discharge may also be in effect in your area. Understand and follow the regula- tions in your area. Be aware of the environment hazards of chemicals that you dispose.

WARNING: Only use the brushes provided with the appliance or those specified in the Operator’s Manual. The use of other brushes may impair safety.

CAUTION: Use of this machine to move other objects or to climb on could result in injury or damage. Do not use this machine as a step or furniture.

CAUTION: Your machine warranty will be voided if anything other than genuine Nilfisk ALTO parts are used on your machine. Always use Nilfisk ALTO parts for replacement.

CAUTION: This machine contains lead acid batteries. The batteries must be disposed of in an environmentally acceptable manner.

WARNING: GENERAL SAFETY RULES

The rules below have to be followed carefully in order to avoid injury to the operator and damage to the machine:

•During the operation of this machine, pay attention to other people around you, especially children.

•Use care when reversing machine in confined areas.

•Do not mix different kinds of detergents. Avoid harmful odors.

•Do not place any liquid containers on to the machine.

•The recommended operating temperature should be between 32° F and 104° F.

•The humidity for operating this machine should be between 30 and 95%.

•Do not use acid solutions that could damage the machine.

•In order to prevent floor damage, do not leave brushes running when machine is standing still.

•In case of fire, use a powder extinguisher. Do not use water.

•Do not strike shelving or scaffoldings, where there is danger of falling objects.

•Adapt the utilization speed to the adhesion conditions.

•Do not exceed the declared hill climbing capacity, otherwise the machine could become unstable.

•For any maintenance operation take off the power supply from the machine.

•Do not disassemble any parts which require the use of a tool to be removed.

•Do not wash the machine with direct water jets or with high water pressure nor with corrosive material.

•After every 200 working hours have machine checked by an authorized service person.

Page -4-

Form No. 71274A

Nilfisk ALTO Operator’s Manual - SCRUBTEC R Manual Steering

Page 3 Page 5
Image 4
Page 3 Page 5
Contents English Instructions For Use 30-72Table of Contents Operator Safety Instructions Nilfisk Alto Operator’s Manual Scrubtec R Manual Steering Introduction Introduction & Machine SpecificationsSymbols Used On Scrubtec R Display Screens For Scrubtec R Machine Control Panel Machine Controls and Features How To Prepare the Machine For Operation How To Handle the Packed MachineHow to Unpack the Machine How to Install the BatteriesBattery Maintenance Correct FillShown with Optional Chemical Mixing Sytem How to Charge the BatteriesRecharging the Batteries Level Indicators for the Charge of the Batteries How To Install the SqueegeeHow To Change or Rotate Brushes on Cylindrical Brush Head How To Install The Brush Or Pad on the Boost machine How To Remove The Brush Or Pad on the Boost machineHow To Operate The Machine Seat Adjustment DeluxeHow to Read the Battery Meter see figure 21, a ScreenHow to Operate the Solution Flow How to Operate the Squeegee and the Vacuum MotorHow to Operate the Brush Pressure How to Fill the Solution Tank How to Operate the Forward / Reverse Switch see figureOperating the Machine To traverse the machine follow this procedure Do These Procedures When You Begin Your Work PeriodHow to Clean a Floor How to Clean a Very Dirty Floor Do These Procedures When You End Your Work PeriodHow To Operate the Machine Maintenance Cleaning the Recovery Tank and FilterCleaning the Solution Tank and Filter Manually Draining the Solution TankVac Assisted Solution Tank Drain Squeegee MaintenanceRear Squeegee Blade Replacement Cleaning the Vacuum HosesHOW to Correct Problems in the Machine Cause Action Cause Action Scrubtec R Scrubtec R 571 C Final Assembly Qty Description Rotary Cyl Boost See Detail a Ref. No Qty Description See Detail a Main Frame Assy Cylindrical Main Frame Assy Boost Main Frame Assy Boost Nilfisk Alto Scrubtec R 571 Optional Side Squeegee Lift Assembly Parts List 5/05 Description QtyNilfisk Alto Scrubtec R 571, 586, 571 C, Boost R 1611 2514 Recovery Tank Assembly Nut, Drain Valve 44 31 Solution Tank ASSEMBLY-1 Solution Tank ASSEMBLY-2 Solution Tank ASSEMBLY-2 Steering Column Assy Steering Column Assy 1A, 1B, 1C Nilfisk Alto1A, 1B, 1C 20 19 18 17 AssembledView Cylindrical Head Assembly Parts List 1/11 Drawing #10962A Inch Boost Head Assy Kit-Flex Plate 32 Note 1, TSBCL2010-12 Shield Boost Bearing Note 1, TSBCL2010-12, NoteBushing-Flex Plate Note 1, TSBCL2010-12 Squeegee Assembly 81cm Squeegee Assembly 81cm Squeegee Assembly 99cm Squeegee Assembly 99cm Squeegee Assembly 104cm Squeegee Assembly 104cm Front Squeegee Assy Rotary Machines only Qty DescriptionFront Squeegee ARM Assy Rotary Machines only Nilfisk Alto Scrubtec R 571, 586, 571 C, Boost R Qty Description Electrical Connection Diagram 9/06 PagesNilfisk Alto -68- Form No a Page Nilfisk Alto Operator’s Manual Scrubtec R Manual Steering Page Scrubtec R 571 Disc Model DeletedScrubtec R 586 Disc Model Scrubtec R 571 C Cylindrical ModelPage Page
Related manuals
Manual 72 pages 47.09 Kb

586, 571 specifications

Nilfisk-ALTO has long been recognized for its commitment to delivering high-quality cleaning solutions, and the Nilfisk-ALTO 586, 571, R 571 C, SCRUBTEC R 586, and SCRUBTEC R 571 models exemplify this dedication. These compact and efficient scrubbers are designed for effective cleaning in various environments, making them suitable for both industrial and commercial applications.

The Nilfisk-ALTO 586 and SCRUBTEC R 586 models feature advanced scrubbing technology, providing users with exceptional cleaning results. They are equipped with a highly efficient brush system that can adapt to different floor surfaces, ensuring optimal cleaning performance whether in retail spaces, warehouses, or manufacturing facilities. The unique brush design simplifies the replacement process, allowing operators to switch brushes quickly and easily.

Among their key characteristics is the ability to adjust the water flow and detergent dose to suit the specific cleaning requirements. This contributes to sustainability, as it minimizes water and detergent waste while maximizing cleaning efficacy. Additionally, their ergonomic design promotes user comfort during operation, reducing fatigue during extended cleaning tasks.

The SCRUBTEC R 571 and R 571 C models bring technological advancements, including a patented electronic control system that manages all aspects of the cleaning process. This system allows users to monitor performance metrics in real-time, providing valuable insights into efficiency and usage patterns. Integrated with a large capacity solution tank, these machines can sustain longer cleaning cycles without frequent refills, making them ideal for larger areas.

Another notable feature is the ultra-compact design of these models, which facilitates maneuverability in tight spaces. Their low profile and slim design allow operators to access hard-to-reach areas, ensuring comprehensive cleaning results. Furthermore, the machines are equipped with advanced noise reduction technology, making them suitable for use in noise-sensitive environments.

Overall, the Nilfisk-ALTO 586, 571, R 571 C, SCRUBTEC R 586, and SCRUBTEC R 571 smoothie’s state-of-the-art features and technologies offer exceptional cleaning efficiency. Their operational flexibility, coupled with user-friendly controls, positions them as an ideal choice for businesses looking to invest in reliable and effective floor cleaning solutions. With Nilfisk-ALTO, users can count on superior performance and durability built into every model.
Top Page Image Contents