Nilfisk-ALTO 571, 586 manual How to Clean a Floor

Page 21

How To Operate the Machine

How to Clean a Floor

WARNING: Water solutions or cleaning materials used with this type of machine can leave wet areas on the floor surface. These areas can cause a dangerous condi- tion for the operator or other persons. Always put CAUTION signs near the area you are cleaning.

For one touch automatic cleaning follow this procedure:

1. Turn the key switch to the “OFF” position.

2. Put the water and a cleaning chemical in the solution tank.

Figure 33

3.Sit on the driver seat. NOTE: The machine will not traverse if the operator is not properly seated.

4.Turn the key switch “ON”. NOTE: The key switch turns on the battery and LED screen displays, which shows the machines condition.

5.The machine has a one touch button on the control panel (see figure 33) that is preset for brush pressure and solution flow. Momentarily depress the one touch button if you wish to use these settings.

NOTE: If this is not the settings that you desire see page 16 or one touch operation.

For manual control of cleaning process, follow these procedures:

1.Turn the key switch to the “OFF” position.

2.Put the water and a cleaning chemical in the solution tank.

3.Sit on the driver seat. NOTE: The machine will not traverse if the operator is not properly seated.

4.Turn the key switch “ON”. NOTE: The key switch turns on the battery and LED screen displays, which shows the machines condition.

5.Lower the squeegee. NOTE: The vacuum motor will turn on when the squeegee up/down switch is placed in the lower posi- tion.

6.Lower the brush head until it reaches the full stroke down. NOTE:

The brushes will start rotating only when the machine begins to traverse.

7.Reset the solution flow valve by using the + / - solution switch.

NOTE: The solution will flow only if the machine is moving forward.

8.After a few feet of scrubbing, check to see that the amount of solu- tion being applied is correct and that the squeegee is picking up water and drying the floor. Make adjustments as required.

9.Once the machine is set properly continue to scrub until the solution low indicator comes on or until you run out of solution.

NOTE: When making multiple passes across the floor, overlap the brush cleaning path approximately 2 inches (5 cm) of the area already cleaned by the brush.

NOTE: During most cleaning procedures, apply and remove the solution in one operation.

Nilfisk ALTO Operator’s Manual - SCRUBTEC R Manual Steering

Form No. 71274A

Page -21-

Page 20 Page 22
Image 21
Page 20 Page 22
Contents 30-72 English Instructions For UseTable of Contents Operator Safety Instructions Nilfisk Alto Operator’s Manual Scrubtec R Manual Steering Introduction & Machine Specifications IntroductionSymbols Used On Scrubtec R Display Screens For Scrubtec R Machine Control Panel Machine Controls and Features How To Handle the Packed Machine How To Prepare the Machine For OperationHow to Unpack the Machine How to Install the BatteriesCorrect Fill Battery MaintenanceHow to Charge the Batteries Shown with Optional Chemical Mixing SytemRecharging the Batteries How To Install the Squeegee Level Indicators for the Charge of the BatteriesHow To Change or Rotate Brushes on Cylindrical Brush Head How To Remove The Brush Or Pad on the Boost machine How To Install The Brush Or Pad on the Boost machineSeat Adjustment Deluxe How To Operate The MachineScreen How to Read the Battery Meter see figure 21, aHow to Operate the Squeegee and the Vacuum Motor How to Operate the Solution FlowHow to Operate the Brush Pressure How to Operate the Forward / Reverse Switch see figure How to Fill the Solution TankOperating the Machine Do These Procedures When You Begin Your Work Period To traverse the machine follow this procedureHow to Clean a Floor Do These Procedures When You End Your Work Period How to Clean a Very Dirty FloorHow To Operate the Machine Cleaning the Recovery Tank and Filter MaintenanceManually Draining the Solution Tank Cleaning the Solution Tank and FilterVac Assisted Solution Tank Drain Squeegee MaintenanceCleaning the Vacuum Hoses Rear Squeegee Blade ReplacementHOW to Correct Problems in the Machine Cause Action Cause Action Scrubtec R Scrubtec R 571 C Final Assembly Qty Description Rotary Cyl Boost See Detail a Ref. No Qty Description See Detail a Main Frame Assy Cylindrical Main Frame Assy Boost Main Frame Assy Boost Nilfisk Alto Scrubtec R 571 Description Qty Optional Side Squeegee Lift Assembly Parts List 5/05Nilfisk Alto Scrubtec R 571, 586, 571 C, Boost R 1611 2514 Recovery Tank Assembly Nut, Drain Valve 44 31 Solution Tank ASSEMBLY-1 Solution Tank ASSEMBLY-2 Solution Tank ASSEMBLY-2 Steering Column Assy Steering Column Assy Nilfisk Alto 1A, 1B, 1C1A, 1B, 1C 20 19 18 17 AssembledView Cylindrical Head Assembly Parts List 1/11 Drawing #10962A Inch Boost Head Assy Shield Boost Bearing Note 1, TSBCL2010-12, Note Kit-Flex Plate 32 Note 1, TSBCL2010-12Bushing-Flex Plate Note 1, TSBCL2010-12 Squeegee Assembly 81cm Squeegee Assembly 81cm Squeegee Assembly 99cm Squeegee Assembly 99cm Squeegee Assembly 104cm Squeegee Assembly 104cm Qty Description Front Squeegee Assy Rotary Machines onlyFront Squeegee ARM Assy Rotary Machines only Nilfisk Alto Scrubtec R 571, 586, 571 C, Boost R Qty Description Pages Electrical Connection Diagram 9/06Nilfisk Alto -68- Form No a Page Nilfisk Alto Operator’s Manual Scrubtec R Manual Steering Page Deleted Scrubtec R 571 Disc ModelScrubtec R 586 Disc Model Scrubtec R 571 C Cylindrical ModelPage Page
Related manuals
Manual 72 pages 47.09 Kb

586, 571 specifications

Nilfisk-ALTO has long been recognized for its commitment to delivering high-quality cleaning solutions, and the Nilfisk-ALTO 586, 571, R 571 C, SCRUBTEC R 586, and SCRUBTEC R 571 models exemplify this dedication. These compact and efficient scrubbers are designed for effective cleaning in various environments, making them suitable for both industrial and commercial applications.

The Nilfisk-ALTO 586 and SCRUBTEC R 586 models feature advanced scrubbing technology, providing users with exceptional cleaning results. They are equipped with a highly efficient brush system that can adapt to different floor surfaces, ensuring optimal cleaning performance whether in retail spaces, warehouses, or manufacturing facilities. The unique brush design simplifies the replacement process, allowing operators to switch brushes quickly and easily.

Among their key characteristics is the ability to adjust the water flow and detergent dose to suit the specific cleaning requirements. This contributes to sustainability, as it minimizes water and detergent waste while maximizing cleaning efficacy. Additionally, their ergonomic design promotes user comfort during operation, reducing fatigue during extended cleaning tasks.

The SCRUBTEC R 571 and R 571 C models bring technological advancements, including a patented electronic control system that manages all aspects of the cleaning process. This system allows users to monitor performance metrics in real-time, providing valuable insights into efficiency and usage patterns. Integrated with a large capacity solution tank, these machines can sustain longer cleaning cycles without frequent refills, making them ideal for larger areas.

Another notable feature is the ultra-compact design of these models, which facilitates maneuverability in tight spaces. Their low profile and slim design allow operators to access hard-to-reach areas, ensuring comprehensive cleaning results. Furthermore, the machines are equipped with advanced noise reduction technology, making them suitable for use in noise-sensitive environments.

Overall, the Nilfisk-ALTO 586, 571, R 571 C, SCRUBTEC R 586, and SCRUBTEC R 571 smoothie’s state-of-the-art features and technologies offer exceptional cleaning efficiency. Their operational flexibility, coupled with user-friendly controls, positions them as an ideal choice for businesses looking to invest in reliable and effective floor cleaning solutions. With Nilfisk-ALTO, users can count on superior performance and durability built into every model.
Top Page Image Contents