Harman-Kardon AVR 5550 owner manual Subwoofer

Page 23

System Configuration

decoding modes are available and the surround back amplifier channels will not be used. When this is the case for your system you may wish to take advantage of the availability of this amplifier channel pair for use in powering a second set of speakers that have their source selected by the AVR 5550’s multiroom control system. See page 39 for more information.

When SMALL is selected the system will adjust so that the full complement of 6.1/7.1 surround processing/decoding modes are available, and low-frequency information below the crossover point (identical with the one for the surround speakers) will be sent to the subwoofer output when the subwoofer is set to ON, or to the Front LEFT/RIGHT when subwoofer is set to OFF.

When LARGE is selected the system will adjust so that the full complement of 6.1/7.1 surround processing/decoding modes are available, and a full-range signal will be sent to the surround back channels, with no low-frequency information sent to the subwoofer output.

7.When you have completed your selection for the surround channels, press the ¤ Button D on the remote to move the cursor to

SUBWOOFER.

8. Press the ‹/› Buttons E on the remote to select the option that best describes your system.

The choices available for the subwoofer position will depend on the settings for the other speak- ers, particularly the front left/right positions.

If the front left/right speakers are set to SMALL, the subwoofer will automatically be set to SUB, which is the “on” position.

If the front left/right speakers are set to LARGE, three options are available:

• If no subwoofer is connected to the AVR 5550, press the ‹/› Buttons E on the remote so that NONE appears in the on-screen menu. When this option is selected, all bass informa- tion will be routed to the front left/right “main” speakers.

•If a subwoofer is connected to the AVR 5550, you have the option to have the front left/right “main” speakers reproduce bass frequencies at all times, and have the subwoofer operate only when the AVR 5550 is being used with a digital source that contains a dedicated Low Frequency Effects, or LFE soundtrack. This allows you to use both your main and subwoofer speakers to take advantage of the special bass created for certain movies. To select that option press the

‹/› Buttons E on the remote so that SUB (LFE) appears in the on-screen menu.

•If a subwoofer is connected and you wish to use it for bass reproduction in conjunction with the main front left/right speakers, regardless of the type of program source or Surround mode you are listening to, press the ‹/› Buttons E on the remote so that SUB L/R+LFE appears in the on-screen menu. When this option is selected, a full-range signal will be sent to the front left/right “main” speakers. The subwoofer will receive the front left and right bass frequencies under the crossover frequency selected in another setting on this menu, as described below, and also the LFE soundtrack.

9.When all initial speaker “size” settings have been made, you now have the option to take advantage of the AVR 5550’s Triple Crossover system, which allows individual crossover settings to be made for each speaker grouping set to "Small". The low-fre- quency crossover point is set by the design of your speakers. It is defined as the frequency which is the lowest possible frequency the speaker is capable of reproducing. Before making any changes to the set- tings for the crossover point we suggest that you find the crossover point for the speakers in each of the three groupings, front left/right, center front and surrounds by looking at the specifications page of the speaker’s owner’s manual, by getting that infor- mation from the manufacturer’s Web site, or by con- tacting your dealer or the manufacturer’s customer service department. You will need this figure to accu- rately configure the next group of settings.

The factory default setting for all speaker positions is 100Hz. If that setting is acceptable for all channels, then no adjustments are needed and you may skip this section. However, should you wish to change one of the settings, please proceed by pressing the

⁄Button Dso that the cursor moves back up to the top of the list of setting options. Press the ‹/ › Buttons E so that X-OVERis high- lighted and the menu data will change to the screen shown in Figure 4.

* *

S P E A K E R

S E T U P

* *

 

 

 

 

 

M O D E

 

:

S I Z E

X - O V E R

 

 

 

 

 

L E F T / R I G H T :

1 0 0

H Z

 

 

 

 

 

 

 

 

C E N T E R

:

1 0 0

H Z

 

 

 

 

 

 

 

 

S U R R O U N D

:

1 0 0

H Z

 

 

 

 

 

 

S U R R B A C K :

- - - - -

 

 

 

 

 

 

S U B W O O F E R :

- - - - -

 

 

 

 

 

 

 

 

 

 

B A S S M G R

:

G L O B A L

 

 

B A C K T O M A S T E R M E N U

Figure 4

To change the setting for any of the three speaker groups Left/Right, Center or Surrounds, press the ⁄/¤ Buttons Duntil the cursor is next to the line where you wish to make a change and then press the ‹/› Buttons E until the desired setting appears. The available choices at which point low-frequency information will be sent to the subwoofer (or to the Front Left/Right speakers in case subwoofer is set to OFF), rather than to

the speaker channel, are 40Hz, 60Hz, 80Hz, 100Hz, 120Hz and 200Hz. Pick the choice that is identical to the information for the speakers, or if an exact match is not possible, pick the closest choice that is ABOVE the speaker’s lowfrequency limit to avoid the creation of a low-frequency “hole” where your system will have no bass information.

In cases where LARGE has been selected as the front channel speaker option and LFE+L/R has been selected as the subwoofer option, the front channel sound information below the cross- over point selected for the L/R front speakers (when fronts are set to "Small") will be sent to BOTH the front channel speakers and the sub- woofer.

When all speakers are set to LARGE the crossover point for the fronts (selectable when they are set to "Small") will affect the LFE signal and the bass support for the front speakers by the sub (when the sub is set to L/R+LFE, see above) only. In that case the default value "100Hz" should be kept or selected for the crossover point for the L/R fronts (selectable when they are "Small") as it´s indicated (and marked by *) behind the LEFT/RIGHT line in the speaker setup menu when the X-OVER option is selected.

Note that the crossover point for the surround speakers and the surround back speakers will be identical. That´s why no crossover point for the surround back speakers is selectable or shown in the menu.

Important Note: All settings for the crossover points will be "Global", i.e. they will be identical for all inputs no matter if the BASSMANAGER (see above) was configured for "Global" or "Independent".

10.When all speaker selections have been made, press the ¤ Button Duntil the cursor is next to the BACK TO MASTER MENU line and press the Set Button Fto return to the Main menu.

11.The Speaker Configuration may also be changed at any time without using the full-OSD on-screen menu system by pressing the Speaker

Selector 6 on the front panel or on the remote control. Once the button is pressed, FRONT SPEAKER will appear in both the lower third of the video display and the Main Information Display ˜.

Within five seconds, either press the ‹/› buttons 7 $ on the front panel or the ⁄/¤ buttons

Don the remote to select a different speaker position, or press the Set Button @F to begin the adjustment process for the front left and right speakers.

SYSTEM CONFIGURATION 23

Page 22 Page 24
Image 23
Page 22 Page 24
Contents AVR 5550 Audio/ Video Receiver Power for the Digital RevolutionDeclaration of Conformity Table of ContentsVariety of modes and two modes of VMAx Description and FeaturesFront panel analog A/V inputs, switch- able to outputs IntroductionUnpacking Safety InformationImportant Safety Information Front Panel Controls To select between the Optical See page 40 for more information on tuning stationsCoaxial Ó For more informationFront Panel Information Display Multi Indicator Auto IndicatorDigital Audio Outputs Connect these Rear Panel Connections+ and negative terminals Video source selected by the receiver’s video switcherUnswitched Outlet Switched Outlet AC Power Cord Jack Connect the ACRear Panel Connections Logic 7 Mode Select Button P Transport Controls Main Remote Control FunctionsDirect Button K Tuning Up/Down Channel/8 Channel Direct Input Movies ∆ Play Forward/Reverse/Stop ˚ Mute Zone II Remote Control FunctionsVideo Equipment Connections Installation and ConnectionsAudio Equipment Connections Scart A/V Connections Important Note for the Use SCART-Cinch Adapters If you use a unit providing RGB signals on aRGB signals can be pathed through System and Power Connections Speaker Selection Speaker PlacementFirst Turn On System ConfigurationUsing the On-Screen Display System SetupSpeaker Setup Input SetupSurround Subwoofer Surround Setup To call up the menu Adjustments for Other InputsDelay Settings Night Mode SettingsPress and hold the SPL Indicator Select Output Level AdjustmentUsing EzSet So that on is highlighted Sensor and Indicator offUp the Volume until you can hear the test noise clearly Operation Surround Mode ChartBut no surround speakers No delay availableMix of the in-phase material of the left and right channels No surround channelsChannel/8-Channel Direct Input Basic OperationSource Selection One of the most important features Controls and Use of HeadphonesSurround Mode Selection Volume Up/Down ButtonsMP3 Audio Playback Digital Audio PlaybackDolby Digital PCM Audio PlaybackSelecting a Digital Source MP 3 DSP mode found in the newDigital Bitstream Indicators Speaker/Channel IndicatorsOr 2 Outputs Night ModeTape Recording Front Panel In/OutputsIndicator Select Output Level Adjustment With Source SignalsMemory Backup Display Brightness Advanced FeaturesTurn On Volume Level Surround Amplifier Channel AssignmentInstallation Advanced Features / Multiroom OperationSemi-OSD Settings Full-OSD Time Out AdjustmentMultiroom Operation Multiroom SetupMultiroom Operation RS-232 ControlRDS Operation Tuner OperationBasic Tuner Operation Program Search PTY RDS stationMust be repeated first Programming the Remote with CodesDirect Code Entry If the unit you wish to program intoErasing Learned Codes Programming the RemoteCode Readout Learning Codes from a RemotePress the AVR Selector Erasing Macro CommandsMacro Programming 4and the Mute button Volume Punch-ThroughProgrammed Device Functions Remote With Other DevicesSelector button Channel Control Punch-ThroughResetting the Remote Memory Function List Prev Channel 1 2 3 4 5 6 7 Clear Power On Power Off Mute TV Select Channel +Power On Power Off VID 3 Select Channel + Scan Scan + Rewind Play Fast Fwd Record Stop PauseRemote sensor ¯ is obscured Troubleshooting GuideProcessor Reset Power Switch 1 is pushedTechnical Specifications Harman Consumer International

AVR 5550 specifications

The Harman-Kardon AVR 5550 is a highly regarded audio/video receiver that embodies a perfect blend of power, performance, and versatility. Designed for the discerning home theater enthusiast, this model delivers a remarkable audio-visual experience with its robust set of features and cutting-edge technologies.

One of the standout characteristics of the AVR 5550 is its impressive power output. With 100 watts per channel across seven channels, it is capable of driving a wide range of speakers with clarity and authority. The amplifier section employs Harman-Kardon's legendary technology to ensure low distortion and a dynamic listening experience. This level of power allows users to experience immersive sound in their home theaters, making it ideal for movie nights and music playback alike.

Equipped with a variety of connectivity options, the AVR 5550 is designed to integrate seamlessly with modern audio and video sources. The receiver features numerous HDMI inputs to accommodate multiple devices, including Blu-ray players, gaming consoles, and streaming devices. Additionally, it provides optical and coaxial digital inputs, as well as analog inputs for older equipment. This comprehensive set of connectivity options ensures that users can enjoy a wide range of media without the hassle of frequently switching cables.

The AVR 5550 also includes advanced surround sound processing technologies, like Dolby Digital and DTS, which contribute to its ability to create an enveloping soundstage. The integration of Harman-Kardon’s own Logic 7 technology enhances the audio experience by utilizing multi-channel processing to extract the best sound from stereo and multi-channel sources alike.

In terms of design, the AVR 5550 sports a sleek, modern aesthetic that fits well into any home theater setup. The intuitive user interface and remote control make it easy for users to navigate settings and choose their desired audio modes. The receiver also features a built-in AM/FM tuner, expanding its functionality beyond just home theater use.

Lastly, the AVR 5550 emphasizes user-friendly features such as on-screen displays and programmable presets, allowing personal preferences to be easily adjusted. Whether for casual listening or full-fledged cinematic experiences, the Harman-Kardon AVR 5550 stands out as a dependable and high-quality option that caters to all audiovisual needs. Its fusion of power, versatility, and advanced technologies makes it a favorite among audio enthusiasts around the world.
Top Page Image Contents