Harman-Kardon AVR 1600 owner manual Macros, Resetting the Remote, Processor Reset, Memory

Page 36

ADVANCED FUNCTIONS

You may reassign the transport control punch-through programming for the AVR, VID2 and VID3 devices to other devices, such as CD. If you wish to remove transport control punch-through altogether for the AVR, VID2 or VID3 device, follow the same procedure as for programming punch-through, but in Step 3 press either of the other two of these three special selector buttons. For example, to remove punch-through transport control from the VID3 device so that press- ing any of the transport controls will have no effect, press and hold the VID3 Button until the Program Indicator LED flashes in amber, then press the Play Button, followed by either the AVR or VID2 Button.

Macros

Macros are used to program sequences of up to 19 commands that are executed with a single button press. Macros are well suited for power on and off commands, or to send out a favorite multidigit channel number with one button press, or to have the ability to send out a code sequence to control a device while the remote is operating another device, but with more flexibility than the built-in punch-through controls.

Some commands may not be programmed into macros: Mute, Dim, or Channel Up/Down.

NOTE: Use caution when programming complicated macros. It isn’t possible to program a pause or delay before sending commands after Power On, and the component may not be ready to respond to commands instantaneously after powering on.

To program, or “record” a macro, follow these steps:

1.Simultaneously press one of the four Macro Buttons or the Power On Button and the Mute Button to enter program mode.

2.Press the Input (or AVR) Selector for each device before you enter commands to be transmitted to that device. This step counts as one of the 19 commands allowed for each macro.

3.For the Power On command, DO NOT press the Power On Button. Press the Mute Button instead.

4.Press the Power Off Button to program the Power Off command.

5.Press the Sleep Button to end the programming process.

To execute the macro, press the Macro Button (or the AVR Power On Button) selected in the first step of programming the macro.

It isn’t possible to “edit” a command within a macro. However, you may erase the macro as follows:

1.Simultaneously press and hold the Mute Button and the Macro Button containing the macro until the LED flashes.

2.Press the Channel Down Button to erase the macro.

Resetting the Remote

To reset the remote to its factory defaults, simultaneously press and hold any Input Selector and the “0” Numeric Key. When the Program LED flashes in amber, enter the code “333”. When the green LED goes out, the remote will have been fully reset.

PROCESSOR RESET

If the unit behaves erratically after a power surge, first turn off the Main Power Switch and unplug the AC power cord for at least 3 minutes. Plug the cord back in and turn the receiver on. If this doesn’t help, reset the AVR.

NOTE: A system reset erases all user configurations, including Source settings, speaker and level settings, and tuner presets. After a reset, reenter all of these settings from your notes in the appendix worksheets.

To reset the AVR 1600, place it in Standby mode (press the front- panel Standby/On Switch so that the Power Indicator turns amber). Then press and hold the front-panel Surround Mode Button for at least 5 seconds until the RESET message appears.

If the receiver does not function correctly ofter a processor reset, contact an authorized Harman Kardon service center for assistance. Authorized service centers may be located by visiting the Web site at www.harmankardon.com.

MEMORY

If the AVR 1600 is unplugged or experiences a power outage, it will retain user settings for up to four weeks.

36

Page 35 Page 37
Image 36
Page 35 Page 37
Contents AVR Safety Information Important Safety InstructionsService Instructions Outdoor Use Marking Wet Location MarkingImportant Safety Information UnpackingTable of Contents Introduction Surround ModesSupplied Accessories Audio InputsAudio/Video Inputs Digital Audio InputsFront PanelControls On When the AVR is turned on, this LED turns white Tuning Press these buttons to tune a radio stationVolume Knob Turn this knob to raise or lower the volume FRONT-PANEL ControlsRear ConnectionsREAR-PANEL Connections Main Remote Control Functions AM/FMMain Remote Control Functions Main Remote Control Functions Introduction to Home Theater Typical Home Theater SystemMultichannel Audio Harman International the Harman Kardon parent company LogicConnecting Source Devices to the AVR Speaker ConnectionsSubwoofer Audio ConnectionsVideo Connections Analog AudioDigital Video Analog VideoAntennas USB PortSpeaker Placement Front Speaker PlacementPlacement of Surround Speakers in a 5.1-Channel System Subwoofer PlacementGetting Started Source Assignment WorksheetGetting Started Installation Step Nine Turn On the AVR Turn on your source deviceTwo steps are required the first time you turn on the AVR Initial Setup Using the ON-SCREEN Menu SystemConfigure the AVR 1600, Using EzSet/EQ Technology Set Up Sources Select Cancel to return to the Master menuSource Indicates the currently selected source. Use the 7/3 System Settings Channel InputsInitial Setup Operation Using the Radio Selecting a Surround ModeRecording AUX InputOperation Analog Audio Signals Digital Audio SignalsAdvanced Functions Audio Processing and Surround SoundDolby Surround Settings Manual Speaker SetupVideo Game Logic 7 Game Step Three Manual Setup Menu Step ONE Determine Speaker CrossoverStep TWO Measure Speaker Distances Number of SpeakersSub Mode Step Four Setting Channel Output Levels ManuallyCrossover Menu Distance MenuAudio Settings System SettingsAdvanced Remote Control Functions Dim FunctionPunch-Through Programming To program punch-through control while operating any deviceResetting the Remote Processor ResetMacros MemoryTroubleshooting Guide Symptom Cause SolutionAppendix Table A1 Recommended Source Component ConnectionsTable A2 Source Setting Defaults Table A3 Speaker/Channel Setting DefaultsTable A4 Delay Setting Defaults Table A5 Source Input Settings Table A6 Speaker/Channel SettingsDigital Channel Level SubwooferTable A7 Remote Control Codes Table A8 System SettingsFeature Default Setting Your Setting Source Input Product Type circle oneSurround Mode Description Incoming Bitstream or Signal Table A9 Surround ModesTable A9 DTS 2/2/.0 or .1, 3/2/.0 or Channel music recordingsLogic 7 Game Channel StereoRemote Control Function List Reference Table A10 Remote Control Function List DVD CD/CD-RTable A10 TV VID3Table A11 Remote Control Product Codes TV Table A12 Remote Control Product Codes VCR Table A13 Remote Control Product Codes CDTable A12 Table A14 Remote Control Product Codes DVD Table A15 Remote Control Product Codes SATTable A13 Table A14Table A16 Remote Control Product Codes Tape Table A17 Remote Control Product Codes CableTable A15 Table A17AVR 1600 Technical Specifications Audio Section
Top Page Image Contents