Harman-Kardon Comprehensive Guide to Advanced Functions and Audio Settings for Harman Kardon Receivers

Page 34

ADVANCED FUNCTIONS

With up to seven main channels, plus a subwoofer, imaging becomes both more critical and more complex. The goal is to ensure that each channel is heard at the listening position with equal loudness.

EzSet/EQ calibration can handle this critical task for you, simply and automatically. However, the AVR’s Level Adjust menu allows you to calibrate the levels manually, either using the system’s test tone or while playing source material.

1.Make sure all speakers have been placed and connected correctly.

2.Adjust the number of speakers, crossover, distance and sub mode for each speaker in your system, as described in Step Three.

3.Measure the channel levels in one of these ways, and adjust the channel levels using the Level Adjust menu:

a)Preferably, use a handheld SPL meter set to the C-Weighting, Slow scale. Adjust each channel so that the meter reads 75dB.

b)By ear. Adjust the levels so that all channels sound equally loud.

c)If you are using a handheld SPL meter with source material, such as a test disc or an audio selection, play it and adjust the AVR’s master volume control until the meter measures 75dB.

Press the OSD Button to display the Master Menu, and then navigate to the Manual Setup line. Press the OK Button to display the Manual Setup menu. Select the Level Adjust line and press the OK Button to display the Level Adjust menu. See Figure 30.

Figure 30 – Level Adjust Menu

All of the speaker channels will appear with their current level settings.

Channel Reset: To reset all of the levels to their factory defaults of 0dB, navigate to this line and change the setting to ON. The levels will be reset, and this setting will remain ON until one of the channel levels is adjusted.

If you are using an external source to set your output levels, navigate to each channel and use the 7/3Buttons to adjust the level as desired. If you would like to set your levels using the AVR 1600’s internal test tone, adjust the TEST TONE SEQ and TEST TONE lines as follows.

Test Tone SEQ: When this setting reads AUTO, the test tone will automatically circulate to all channels, pausing for a few moments at each channel for several seconds, as indicated by the blinking cursor. Adjust the level for any channel when the test tone is paused there by using the 7/3Buttons. You may also use the 5/1Buttons at any time to move the cursor to another line, and the test tone will follow the cursor.

When this setting reads MANUAL, the test tone will not move to the next channel until you use the 5/1Buttons.

Test Tone: This line determines whether the test tone is active. To begin the process of setting the levels, use the 7/3Buttons to change

the setting to ON. Any time you manually move the cursor out of the channel listings area of the screen, this setting will automatically change to OFF, stopping the test tone.

Individual Channels: If you are using an external source to set your output levels, navigate to each channel and use the

7/3 Buttons to adjust the level, between –10dB and +10dB. The level settings are global for all sources and surround modes.

When you have finished adjusting the speaker levels, select the Back to Manual Setup option or press the OSD Button. Record the level settings in Table A3 in the appendix.

AUDIO SETTINGS

To adjust other audio settings, such as the tone controls, press the OSD Button to display the Master Menu. With the cursor pointing to INPUT SETUP, press the OK Button to display the Input Setup menu, where the source, its title, its component video and audio inputs and Auto Polling status may be adjusted, as described in the Initial Setup section. However, this section will focus on the four audio settings:

BXR: Enhances bass performance when playing MP3 tracks. Select On, or leave at the default Off setting for

non-MP3 audio.

Tone: Determines whether the treble and bass controls are active. When it’s OUT, the tone controls are “flat”, with no changes. When it’s IN, the bass and treble frequencies are boosted or cut, depending upon the tone-control settings. When an analog audio source is in use and the 2-Channel Stereo surround mode is selected, setting the Tone Control to “OUT” places the unit in analog bypass mode.

Treble and Bass: Boost or cut the high or low frequencies by up to 10dB, 2dB at a time by using the 7/3 Buttons. The default setting is 0dB.

When you have finished, press the OSD Button.

SYSTEM SETTINGS

The AVR 1600 offers system settings for ease of use. These settings may be accessed from the System SETUP menu, which is selected by pressing the OSD Button and navigating to the System Setup line. Press the OK Button to display the System SETUP menu. See Figure 31.

Figure 31 – Systems Setup Menu

VFD Fade Time Out: Some people find the brightness of the AVR’s front-panel display distracting during movies or listening sessions. It’s possible to dim the front-panel display completely using the Dim function (see below). This sets the display to remain dark most of the time, lighting up only when a button is pressed

34

Image 34
Contents AVR Service Instructions Outdoor Use Marking Safety InformationImportant Safety Instructions Wet Location MarkingImportant Safety Information UnpackingTable of Contents Introduction Surround ModesAudio/Video Inputs Supplied AccessoriesAudio Inputs Digital Audio InputsPanel FrontControls Volume Knob Turn this knob to raise or lower the volume On When the AVR is turned on, this LED turns whiteTuning Press these buttons to tune a radio station FRONT-PANEL ControlsRear ConnectionsREAR-PANEL Connections Main Remote Control Functions AM/FMMain Remote Control Functions Main Remote Control Functions Multichannel Audio Introduction to Home TheaterTypical Home Theater System Harman International the Harman Kardon parent company LogicSubwoofer Connecting Source Devices to the AVRSpeaker Connections Audio ConnectionsDigital Video Video ConnectionsAnalog Audio Analog VideoAntennas USB PortPlacement of Surround Speakers in a 5.1-Channel System Speaker PlacementFront Speaker Placement Subwoofer PlacementGetting Started Source Assignment WorksheetGetting Started Installation Turn on your source device Step Nine Turn On the AVRTwo steps are required the first time you turn on the AVR Using the ON-SCREEN Menu System Initial SetupConfigure the AVR 1600, Using EzSet/EQ Technology Select Cancel to return to the Master menu Set Up SourcesSource Indicates the currently selected source. Use the 7/3 System Settings Channel InputsInitial Setup Operation Recording Using the RadioSelecting a Surround Mode AUX InputOperation Advanced Functions Analog Audio SignalsDigital Audio Signals Audio Processing and Surround SoundManual Speaker Setup Dolby Surround SettingsVideo Game Logic 7 Game Step TWO Measure Speaker Distances Step Three Manual Setup MenuStep ONE Determine Speaker Crossover Number of SpeakersCrossover Menu Sub ModeStep Four Setting Channel Output Levels Manually Distance MenuAudio Settings System SettingsPunch-Through Programming Advanced Remote Control FunctionsDim Function To program punch-through control while operating any deviceMacros Resetting the RemoteProcessor Reset MemoryTroubleshooting Guide Symptom Cause SolutionAppendix Table A1 Recommended Source Component ConnectionsTable A3 Speaker/Channel Setting Defaults Table A2 Source Setting DefaultsTable A4 Delay Setting Defaults Digital Table A5 Source Input SettingsTable A6 Speaker/Channel Settings Channel Level SubwooferFeature Default Setting Your Setting Table A7 Remote Control CodesTable A8 System Settings Source Input Product Type circle oneSurround Mode Description Incoming Bitstream or Signal Table A9 Surround ModesTable A9 Logic 7 Game DTS 2/2/.0 or .1, 3/2/.0 orChannel music recordings Channel StereoRemote Control Function List Reference Table A10 Remote Control Function List DVD CD/CD-RTable A10 TV VID3Table A11 Remote Control Product Codes TV Table A13 Remote Control Product Codes CD Table A12 Remote Control Product Codes VCRTable A12 Table A13 Table A14 Remote Control Product Codes DVDTable A15 Remote Control Product Codes SAT Table A14Table A15 Table A16 Remote Control Product Codes TapeTable A17 Remote Control Product Codes Cable Table A17AVR 1600 Technical Specifications Audio Section