Harman-Kardon Explore the Features and Controls of the Harman Kardon AVR 1600

Page 8

FRONT-PANEL CONTROLS

Power Indicator: This LED has three possible modes:

Main Power Off: When the AVR is unplugged or the rear- panel Main Power Switch is off, this LED is off.

Standby: Amber indicates that the AVR is ready to be turned on.

On: When the AVR is turned on, this LED turns white.

NOTE: If the PROTECT message ever appears, turn off the AVR and unplug it. Check all speaker wires for a possible short. If none is found, bring the unit to an authorized Harman Kardon service center for inspection and repair before using it again.

Standby/On Switch: This electrical switch turns the receiver on, or places it in Standby mode for quick turn-on.

Tuning Mode: This button toggles between manual (one frequency step at a time) and automatic (seeks frequencies with acceptable signal strength) tuning mode. It also toggles between stereo and mono modes when an FM station is tuned.

Channel Level Control: Press this button to adjust the output level for any amplifier channel. It may be necessary to raise or lower the level of a specific channel to compensate for the placement of the relevant speaker in the room in relation to the listening position, e.g. the center channel speaker is further away from the listening position than the front left and right speakers, so that the dialogue is too soft to hear clearly.

To adjust the level of a channel, press this button once. If the desired channel is not displayed on screen and in the front-panel Message Display, use the Tuning Buttons to scroll to it. When the desired channel appears, use the 7/3 Navigation Buttons to change the level.

It is recommended that you avoid changing the channel levels after you have run the EzSet/EQ setup procedure described in the Initial Setup section, which properly adjusts all channel levels. See the Advanced Functions section for more information on manual speak- er setup, including level adjustment.

Remote IR Sensor: This sensor receives infrared (IR) commands from the remote control. It is important to ensure that it is not blocked. If covering the sensor is unavoidable, use an optional Harman Kardon HE 1000, or other infrared receiver, connecting it to the Remote IR Input on the AVR 1600’s rear panel.

Digital Input: To change the audio input for the current source to one of the six digital audio inputs or the analog input for the source, press this button and use the 7/3 Navigation Buttons to change the input. Although any digital audio input may be assigned to any source, the analog audio inputs are all permanently dedicated to the source with which they are labeled.

7/3 Navigation: These buttons are used to navigate the AVR’s menus.

Set: Press this button to select the currently highlighted item.

Message Display: Various messages appear in this two-line display in response to commands and changes in the incoming signal. In normal operation, the current source name appears on the upper line, while the surround mode is displayed on the lower line. When the on-screen display menu system (OSD) is in use, the current menu settings appear.

Tuning: Press these buttons to tune a radio station.

Surround Modes: Press this button to select a surround sound (e.g., multichannel) mode. Each press changes the surround mode category: AUTO SELECT, VIRTUAL, STEREO, MOVIE, MUSIC, VIDEO GAME. To change the specific mode within the category, use the Surround Select Buttons. See the Advanced Functions section for more information on surround modes.

Surround Select: After you have selected the desired surround mode category, press these buttons to select a specific mode within the category, such as to change from Dolby Pro Logic IIx Movie mode to Logic 7 Movie mode. Surround mode availability depends on the nature of the source input signal, i.e. digital versus analog, and number of channels encoded within the signal.

Source Selectors: Press these buttons to select a source device, which is a component where a playback signal originates, e.g., DVD.

Headphone Jack/EzSet/EQ Microphone Input: Plug a 1/4” headphone plug into this jack for private listening.

This jack is also used to connect the supplied microphone for the EzSet/EQ procedure described in the Initial Setup section.

Digital Audio Inputs (Optical 3 and Coaxial 3):

Connect a source component that will only be used temporarily, such as a digital camera or game console, to these jacks. Use only one type of audio. The audio input may be assigned to any video source.

USB Port: This port may be used in case a software upgrade for the receiver is offered in the future. Do not connect a storage device, peripheral product or a PC here, unless instructed to do so as part of an upgrade procedure.

Video 3 Analog Audio and Video Inputs: Connect a source component that will only be used temporarily, such as a digital camera or game console, to these jacks. These inputs are selected as the Video 3 source, and may not be assigned to other sources.

Volume Knob: Turn this knob to raise or lower the volume.

8

Image 8
Contents AVR Safety Information Important Safety InstructionsService Instructions Outdoor Use Marking Wet Location MarkingImportant Safety Information UnpackingTable of Contents Introduction Surround ModesSupplied Accessories Audio InputsAudio/Video Inputs Digital Audio InputsControls FrontPanel On When the AVR is turned on, this LED turns white Tuning Press these buttons to tune a radio stationVolume Knob Turn this knob to raise or lower the volume FRONT-PANEL ControlsRear ConnectionsREAR-PANEL Connections Main Remote Control Functions AM/FMMain Remote Control Functions Main Remote Control Functions Introduction to Home Theater Typical Home Theater SystemMultichannel Audio Harman International the Harman Kardon parent company LogicConnecting Source Devices to the AVR Speaker ConnectionsSubwoofer Audio ConnectionsVideo Connections Analog AudioDigital Video Analog VideoAntennas USB PortSpeaker Placement Front Speaker PlacementPlacement of Surround Speakers in a 5.1-Channel System Subwoofer PlacementGetting Started Source Assignment WorksheetGetting Started Installation Two steps are required the first time you turn on the AVR Step Nine Turn On the AVRTurn on your source device Configure the AVR 1600, Using EzSet/EQ Technology Initial SetupUsing the ON-SCREEN Menu System Source Indicates the currently selected source. Use the 7/3 Set Up SourcesSelect Cancel to return to the Master menu System Settings Channel InputsInitial Setup Operation Using the Radio Selecting a Surround ModeRecording AUX InputOperation Analog Audio Signals Digital Audio SignalsAdvanced Functions Audio Processing and Surround SoundVideo Game Logic 7 Game Dolby Surround SettingsManual Speaker Setup Step Three Manual Setup Menu Step ONE Determine Speaker CrossoverStep TWO Measure Speaker Distances Number of SpeakersSub Mode Step Four Setting Channel Output Levels ManuallyCrossover Menu Distance MenuAudio Settings System SettingsAdvanced Remote Control Functions Dim FunctionPunch-Through Programming To program punch-through control while operating any deviceResetting the Remote Processor ResetMacros MemoryTroubleshooting Guide Symptom Cause SolutionAppendix Table A1 Recommended Source Component ConnectionsTable A4 Delay Setting Defaults Table A2 Source Setting DefaultsTable A3 Speaker/Channel Setting Defaults Table A5 Source Input Settings Table A6 Speaker/Channel SettingsDigital Channel Level SubwooferTable A7 Remote Control Codes Table A8 System SettingsFeature Default Setting Your Setting Source Input Product Type circle oneSurround Mode Description Incoming Bitstream or Signal Table A9 Surround ModesTable A9 DTS 2/2/.0 or .1, 3/2/.0 or Channel music recordingsLogic 7 Game Channel StereoRemote Control Function List Reference Table A10 Remote Control Function List DVD CD/CD-RTable A10 TV VID3Table A11 Remote Control Product Codes TV Table A12 Table A12 Remote Control Product Codes VCRTable A13 Remote Control Product Codes CD Table A14 Remote Control Product Codes DVD Table A15 Remote Control Product Codes SATTable A13 Table A14Table A16 Remote Control Product Codes Tape Table A17 Remote Control Product Codes CableTable A15 Table A17AVR 1600 Technical Specifications Audio Section