Brother EN 1470, HS 2000 operation manual GTrim the excess thread above the bobbin

Page 14

KNOWING YOUR SEWING MACHINE —————————————————————————————————————————

fWhile holding the end of the thread, gently press the foot controller or press (start/ stop button) (for models equipped with the start/stop button) to wind the thread around the bobbin a few times. Then stop the machine.

Note

●If the sewing machine is to be operated using the foot controller, connect the foot controller before turning on the machine.

●When the foot controller is plugged in, the start/stop button cannot be used to start sewing (only for models equipped with the start/stop button).

gTrim the excess thread above the bobbin.

CAUTION

●Make sure you follow the instructions carefully. If you do not cut the thread completely, and the bobbin is wound, when the thread runs low it may tangle around the bobbin and cause the needle to break.

hSlide the sewing speed controller to the right (to set the speed to fast). (For models equipped with the sewing speed controller.)

iPress the foot controller or press (start/ stop button) (for models equipped with the start/stop button) to start.

jWhen the bobbin seems full and begins spinning slowly, take your foot off the foot controller or press (start/stop button) (for models equipped with the start/stop button).

kCut the thread, slide the bobbin winder shaft to the left and remove the bobbin.

lSlide the sewing speed controller back to its original position (for models equipped with the sewing speed controller).

Memo

●When the sewing machine is started or the handwheel is turned after winding the thread around the bobbin, the machine will make a clicking sound; this is not a malfunction.

●The needle bar does not move when you slide the bobbin winding shaft to the right.

CAUTION

●Not winding the bobbin properly may cause the thread tension to loosen, and may break the needle.

12

aWound evenly

bWound poorly

aSewing speed controller

12

Page 13 Page 15
Image 14
Page 13 Page 15
Contents Computerized Sewing Machine Important Safety Instructions For a longer service life For repair or adjustment For Users in the UK, EIRE, Malta and Cyprus onlyContents Utility Stitches Names of Machine Parts and Their Functions Main partsButtons provided on some models Needle and presser foot sectionOperation buttons ASlideopen theit. flat bed attachment to the left to Operation panelFlat bed attachment Accessories Optional accessoriesBSet the main power switch to Using Your Sewing MachinePower supply precautions CTo turn off the machine, set the main power switch toSide of stitch selection key Foot controllerChanging the needle stop position ETurn on the sewing machine Threading the MachineWinding the bobbin GTrim the excess thread above the bobbin Thread is cut to a suitable length For models equipped with the fast bobbin winding systemCSlide the bobbin winder shaft to the right Lower threading For models equipped with the quick-set bobbin Upper threading Thread take-up lever Machine Fully lower the needle threader leverGthe needle toward the back of the sewing ECatch the thread on the hook as shown belowALightly hold the end of the upper thread Drawing up the lower threadFor models equipped with the quick-set bobbin Bobbin cover should still be removedNeedle types and their uses Needle precautionsReplacing the Needle This section provides information on sewing machine needlesCorrect needle Checking the needleReplacing the needle Incorrect needleInstalling the needle clamp Install the twin needle in the same waySewing with a twin needle Twin needle threadingReplace the presser foot as described below Replacing the Presser FootReplacing the presser foot Mark on the wheel points up. With modelsAttaching the presser foot holder Removing the presser foot holderRemoving the presser foot holder ARemove the presser footSewing General sewing procedureFollow the basic procedures below to sew ATurn on the sewing machine DIfwidth.necessary, adjust the stitch lengthSelecting stitching CAttach the presser foot indicated in the LCDBRaise the presser foot lever Starting to sewOn the wheel points up. With models equipped Correct tension Thread tensionSewing reinforcement stitches Upper tension is too tightThread correctly. For details, refer to page 14 Upper tension is too looseChanging the sewing direction Useful Sewing TipsTrial sewing Sewing curvesSewing hook-and-loop fastener Sewing stretch fabrics Using a free-arm styleSewing thin fabrics ASlidereleasetheit.flat bed attachment to the left toAttach overcasting foot G or zigzag foot J Select a stitch Overcasting StitchesRev. Reverse Rfc. Reinforcement For details, refer to Selecting stitchingBasic stitching FWhen sewing is finished, cut the threadBasic Stitching For details, refer to Starting to sewDFold back the fabric inside along the basting Blind HEM StitchingAReverse the skirt or pants Arm If the needle does not catch the hem fold Auto Rfc Buttonhole SewingButtonholes can be sewn and buttons can be sewn on Size of the buttonhole is set If the button does not fit in the button guide plateFPullpossible.down the buttonhole lever as far as Trim off any excess of the gimp thread Button sewingSewing buttonholes on stretch fabrics CAttach presser foot MAfter sewing for about 10 seconds at low ESelect a stitchWith stitch Select stitch Normally, the feed dog position lever is Positioned atZipper Insertion Rev. ReverseElastic attaching Sewing Stretch Fabrics and Elastic TapeStretch stitching APPLIQUÉ, Patchwork and Quilt Stitching AppliquésPatchwork crazy quilt stitching Edge of the fabric, and sew using stitchPiecing DCarefully sew around the edge of the designABaste the fabric to be quilted Using the optional quilting guideQuilting For details, refer to Removing the presser foot holderFree-motion quilting DSlide the feed dog position lever, located atBar tack stitching Reinforcement StitchingTriple stretch stitching Rfc. Reinforcement **Auto Rfc. Automatic ReinforcementEPullpossible.down the buttonhole lever as far as Decorative Stitching AAttach monogramming foot N BSelect stitch FagotingScallop stitching Fabric.3CSew parallel stitching at intervals of 1 cm 3/8 inch SmockingShell tuck stitching DPull the bobbin threads to create gathersDStart sewing JoiningHeirloom stitching Stitch Settings Utility stitchesRfc. Reinforcement Pattern No Rfc Binding Appendix Cleaning the bobbin case MaintenanceCleaning the machine surface Do not put oil on the bobbin case ERemove the bobbin caseGrasp the bobbin case, and then pull it out Troubleshooting Thread is Tangled on LowerOr breaks Wrong sideStitches are Fabric isWrinkled SkippedError Messages Operation beep for models equipped with the operation beepIndex Numerics31, 34 Page English 885-S38 XE3669-001

HS 2000, EN 1470 specifications

The Brother EN 1470 and HS 2000 are innovative sewing machines that cater to both beginners and experienced sewers alike, offering a host of features and advanced technologies to enhance the sewing experience.

One of the standout features of the Brother EN 1470 is its user-friendly interface, designed with simplicity in mind. This machine offers a wide variety of built-in stitches, allowing users to explore different patterns and styles. With over 100 stitch options, including decorative, utility, and heirloom stitches, the EN 1470 provides immense creative flexibility. The automatic needle threader is another highlight, significantly reducing setup time and enhancing convenience.

The HS 2000, while distinct, shares a similar commitment to usability. It features a robust sewing speed, capable of handling various fabrics, from lightweight materials to heavy-duty textiles. The machine comes equipped with an advanced sewing assist guide, which helps users make quick decisions about settings for specific fabrics and stitch types. Additionally, the HS 2000 has a top-loading bobbin system that simplifies the bobbin change process, ensuring a smooth sewing experience without frustrating interruptions.

Both machines incorporate Brother's advanced technology, including the LED lighting that illuminates the sewing area, allowing for precision work, even in low-light conditions. The ergonomic design also promotes comfortable handling, making lengthy sewing projects less tiring.

Another essential characteristic of the EN 1470 and HS 2000 is their versatility. They accommodate a range of presser feet, which allows for a multitude of sewing techniques such as quilting, zippers, and buttonholes. The built-in buttonhole function is automatic in both models, further simplifying the sewing process while achieving professional results.

Durability is key to the appeal of these machines. Crafted with high-quality materials, they can withstand the demands of regular use. Their compact size and lightweight nature make them portable, perfect for sewing enthusiasts who like to take their work on the go.

In conclusion, the Brother EN 1470 and HS 2000 stand out in the market for their combination of user-friendly features, advanced technologies, and durability. Whether you are a beginner looking to explore the world of sewing or a seasoned professional seeking a reliable machine, both models provide an excellent platform to bring your creative visions to life.
Top Page Image Contents