Brother HS 2000 Checking the needle, Replacing the needle, Correct needle, Incorrect needle

Page 23

CAUTION

●The appropriate fabric, thread and needle combinations are shown in the table on the previous page. If the combination of the fabric, thread and needle is not correct, particularly when sewing thick fabrics (such as denim) with thin needles (such as 65/9 to 75/11), the needle may bend or break. In addition, the stitching may be uneven or puckered or there may be skipped stitches.

Checking the needle

Sewing with a bent needle is extremely dangerous since the needle may break while the machine is being operated.

Before using the needle, place the flat side of the needle on a flat surface and check that the distance between the needle and the flat surface is even.

1

2

aFlat side

bNeedle type marking

■Correct needle

1

aFlat surface

■Incorrect needle

If the distance between the needle and the flat surface is not even, the needle is bent. Do not use a bent needle.

1

aFlat surface

Replacing the needle

Replace the needle as described below. Use the screwdriver and a needle that has been determined

to be straight according to the instructions in1 “Checking the needle” .

aRaise the needle by turning the handwheel toward you (counterclockwise) so that the mark on the wheel points up. (With models equipped with (needle position button), raise the needle by pressing once or twice.)

or

a Mark

b Needle position button

bTurn off the sewing machine.

CAUTION

●Before replacing the needle, be sure to turn off the sewing machine, otherwise injuries may occur if the foot controller or the start/ stop button is accidentally pressed and the machine starts sewing.

cLower the presser foot lever.

aPresser foot lever

21

Page 22 Page 24
Image 23
Page 22 Page 24
Contents Computerized Sewing Machine Important Safety Instructions For a longer service life For Users in the UK, EIRE, Malta and Cyprus only For repair or adjustmentContents Utility Stitches Main parts Names of Machine Parts and Their FunctionsButtons provided on some models Needle and presser foot sectionOperation buttons ASlideopen theit. flat bed attachment to the left to Operation panelFlat bed attachment Optional accessories AccessoriesCTo turn off the machine, set the main power switch to Using Your Sewing MachinePower supply precautions BSet the main power switch toSide of stitch selection key Foot controllerChanging the needle stop position ETurn on the sewing machine Threading the MachineWinding the bobbin GTrim the excess thread above the bobbin Thread is cut to a suitable length For models equipped with the fast bobbin winding systemCSlide the bobbin winder shaft to the right Lower threading For models equipped with the quick-set bobbin Upper threading Thread take-up lever ECatch the thread on the hook as shown below Fully lower the needle threader leverGthe needle toward the back of the sewing MachineBobbin cover should still be removed Drawing up the lower threadFor models equipped with the quick-set bobbin ALightly hold the end of the upper threadThis section provides information on sewing machine needles Needle precautionsReplacing the Needle Needle types and their usesIncorrect needle Checking the needleReplacing the needle Correct needleInstall the twin needle in the same way Installing the needle clampTwin needle threading Sewing with a twin needleMark on the wheel points up. With models Replacing the Presser FootReplacing the presser foot Replace the presser foot as described belowARemove the presser foot Removing the presser foot holderRemoving the presser foot holder Attaching the presser foot holderSewing General sewing procedureFollow the basic procedures below to sew CAttach the presser foot indicated in the LCD DIfwidth.necessary, adjust the stitch lengthSelecting stitching ATurn on the sewing machineBRaise the presser foot lever Starting to sewOn the wheel points up. With models equipped Upper tension is too tight Thread tensionSewing reinforcement stitches Correct tensionUpper tension is too loose Thread correctly. For details, refer to page 14Sewing curves Useful Sewing TipsTrial sewing Changing the sewing directionSewing hook-and-loop fastener ASlidereleasetheit.flat bed attachment to the left to Using a free-arm styleSewing thin fabrics Sewing stretch fabricsFor details, refer to Selecting stitching Overcasting StitchesRev. Reverse Rfc. Reinforcement Attach overcasting foot G or zigzag foot J Select a stitchFor details, refer to Starting to sew FWhen sewing is finished, cut the threadBasic Stitching Basic stitchingDFold back the fabric inside along the basting Blind HEM StitchingAReverse the skirt or pants Arm If the needle does not catch the hem fold Auto Rfc Buttonhole SewingButtonholes can be sewn and buttons can be sewn on If the button does not fit in the button guide plate Size of the buttonhole is setFPullpossible.down the buttonhole lever as far as CAttach presser foot M Button sewingSewing buttonholes on stretch fabrics Trim off any excess of the gimp threadNormally, the feed dog position lever is Positioned at ESelect a stitchWith stitch Select stitch After sewing for about 10 seconds at lowRev. Reverse Zipper InsertionElastic attaching Sewing Stretch Fabrics and Elastic TapeStretch stitching Appliqués APPLIQUÉ, Patchwork and Quilt StitchingDCarefully sew around the edge of the design Edge of the fabric, and sew using stitchPiecing Patchwork crazy quilt stitchingFor details, refer to Removing the presser foot holder Using the optional quilting guideQuilting ABaste the fabric to be quiltedDSlide the feed dog position lever, located at Free-motion quiltingRfc. Reinforcement **Auto Rfc. Automatic Reinforcement Reinforcement StitchingTriple stretch stitching Bar tack stitchingEPullpossible.down the buttonhole lever as far as Decorative Stitching Fabric.3 FagotingScallop stitching AAttach monogramming foot N BSelect stitchDPull the bobbin threads to create gathers SmockingShell tuck stitching CSew parallel stitching at intervals of 1 cm 3/8 inchDStart sewing JoiningHeirloom stitching Utility stitches Stitch SettingsRfc. Reinforcement Pattern No Rfc Binding Appendix Cleaning the bobbin case MaintenanceCleaning the machine surface Do not put oil on the bobbin case ERemove the bobbin caseGrasp the bobbin case, and then pull it out Troubleshooting Wrong side LowerOr breaks Thread is Tangled onSkipped Fabric isWrinkled Stitches areOperation beep for models equipped with the operation beep Error MessagesNumerics Index31, 34 Page English 885-S38 XE3669-001

HS 2000, EN 1470 specifications

The Brother EN 1470 and HS 2000 are innovative sewing machines that cater to both beginners and experienced sewers alike, offering a host of features and advanced technologies to enhance the sewing experience.

One of the standout features of the Brother EN 1470 is its user-friendly interface, designed with simplicity in mind. This machine offers a wide variety of built-in stitches, allowing users to explore different patterns and styles. With over 100 stitch options, including decorative, utility, and heirloom stitches, the EN 1470 provides immense creative flexibility. The automatic needle threader is another highlight, significantly reducing setup time and enhancing convenience.

The HS 2000, while distinct, shares a similar commitment to usability. It features a robust sewing speed, capable of handling various fabrics, from lightweight materials to heavy-duty textiles. The machine comes equipped with an advanced sewing assist guide, which helps users make quick decisions about settings for specific fabrics and stitch types. Additionally, the HS 2000 has a top-loading bobbin system that simplifies the bobbin change process, ensuring a smooth sewing experience without frustrating interruptions.

Both machines incorporate Brother's advanced technology, including the LED lighting that illuminates the sewing area, allowing for precision work, even in low-light conditions. The ergonomic design also promotes comfortable handling, making lengthy sewing projects less tiring.

Another essential characteristic of the EN 1470 and HS 2000 is their versatility. They accommodate a range of presser feet, which allows for a multitude of sewing techniques such as quilting, zippers, and buttonholes. The built-in buttonhole function is automatic in both models, further simplifying the sewing process while achieving professional results.

Durability is key to the appeal of these machines. Crafted with high-quality materials, they can withstand the demands of regular use. Their compact size and lightweight nature make them portable, perfect for sewing enthusiasts who like to take their work on the go.

In conclusion, the Brother EN 1470 and HS 2000 stand out in the market for their combination of user-friendly features, advanced technologies, and durability. Whether you are a beginner looking to explore the world of sewing or a seasoned professional seeking a reliable machine, both models provide an excellent platform to bring your creative visions to life.
Top Page Image Contents