Brother HS 2000, EN 1470 operation manual For models equipped with the fast bobbin winding system

Page 15

■For models equipped with the fast bobbin winding system

aFollow steps 1 through 2 of the procedure in “Winding the bobbin” to pass the thread around the pre-tension disk (page 11).

bPlace the bobbin on the bobbin winder shaft so that the spring on the shaft fits into the notch in the bobbin.

aNotch

bBobbin winder shaft spring

cSlide the bobbin winder shaft to the right.

dWhile holding the thread that wraps around the pre-tension disk with your left hand, use your right hand to wind the free end of the thread clockwise around the bobbin five or six times.

ePull the thread to the right and pass it through the slit in the bobbin winder seat.

aSlit in bobbin winder seat (with built-in cutter)

X The thread is cut to a suitable length.

CAUTION

●Be sure to cut the thread as described. If the bobbin is wound without cutting the thread using the cutter built into the slit in the bobbin winder seat, the thread may become tangled in the bobbin or the needle may bend or break when the bobbin thread starts to run out.

fSlide the sewing speed controller to the right (to set the speed to fast) (for models equipped with the sewing speed controller).

1

aSewing speed controller

gTurn on the sewing machine.

hPress the foot controller or press (start/ stop button) (for models equipped with the start/stop button) to start.

Note

●If the sewing machine is to be operated using the foot controller, connect the foot controller before turning on the machine.

●When the foot controller is plugged in, the start/stop button cannot be used to start sewing (only for models equipped with the start/stop button).

iWhen the bobbin begins spinning slowly, take your foot off the foot controller or press (start/stop button) (for models equipped with the start/stop button).

jCut the thread, slide the bobbin winder shaft to the left and remove the bobbin.

kSlide the sewing speed controller back to its original position (for models equipped with the sewing speed controller).

CAUTION

●Not winding the bobbin properly may cause the thread tension to loosen, and may break the needle.

12

aWound evenly

bWound poorly

13

Page 14 Page 16
Image 15
Page 14 Page 16
Contents Computerized Sewing Machine Important Safety Instructions For a longer service life For Users in the UK, EIRE, Malta and Cyprus only For repair or adjustmentContents Utility Stitches Main parts Names of Machine Parts and Their FunctionsNeedle and presser foot section Operation buttonsButtons provided on some models Operation panel Flat bed attachmentASlideopen theit. flat bed attachment to the left to Optional accessories AccessoriesCTo turn off the machine, set the main power switch to Using Your Sewing MachinePower supply precautions BSet the main power switch toFoot controller Changing the needle stop positionSide of stitch selection key Threading the Machine Winding the bobbinETurn on the sewing machine GTrim the excess thread above the bobbin For models equipped with the fast bobbin winding system CSlide the bobbin winder shaft to the rightThread is cut to a suitable length Lower threading For models equipped with the quick-set bobbin Upper threading Thread take-up lever ECatch the thread on the hook as shown below Fully lower the needle threader leverGthe needle toward the back of the sewing MachineBobbin cover should still be removed Drawing up the lower threadFor models equipped with the quick-set bobbin ALightly hold the end of the upper threadThis section provides information on sewing machine needles Needle precautionsReplacing the Needle Needle types and their usesIncorrect needle Checking the needleReplacing the needle Correct needleInstall the twin needle in the same way Installing the needle clampTwin needle threading Sewing with a twin needleMark on the wheel points up. With models Replacing the Presser FootReplacing the presser foot Replace the presser foot as described belowARemove the presser foot Removing the presser foot holderRemoving the presser foot holder Attaching the presser foot holderGeneral sewing procedure Follow the basic procedures below to sewSewing CAttach the presser foot indicated in the LCD DIfwidth.necessary, adjust the stitch lengthSelecting stitching ATurn on the sewing machineStarting to sew On the wheel points up. With models equippedBRaise the presser foot lever Upper tension is too tight Thread tensionSewing reinforcement stitches Correct tensionUpper tension is too loose Thread correctly. For details, refer to page 14Sewing curves Useful Sewing TipsTrial sewing Changing the sewing directionSewing hook-and-loop fastener ASlidereleasetheit.flat bed attachment to the left to Using a free-arm styleSewing thin fabrics Sewing stretch fabricsFor details, refer to Selecting stitching Overcasting StitchesRev. Reverse Rfc. Reinforcement Attach overcasting foot G or zigzag foot J Select a stitchFor details, refer to Starting to sew FWhen sewing is finished, cut the threadBasic Stitching Basic stitchingBlind HEM Stitching AReverse the skirt or pantsDFold back the fabric inside along the basting Arm If the needle does not catch the hem fold Buttonhole Sewing Buttonholes can be sewn and buttons can be sewn onAuto Rfc If the button does not fit in the button guide plate Size of the buttonhole is setFPullpossible.down the buttonhole lever as far as CAttach presser foot M Button sewingSewing buttonholes on stretch fabrics Trim off any excess of the gimp threadNormally, the feed dog position lever is Positioned at ESelect a stitchWith stitch Select stitch After sewing for about 10 seconds at lowRev. Reverse Zipper InsertionSewing Stretch Fabrics and Elastic Tape Stretch stitchingElastic attaching Appliqués APPLIQUÉ, Patchwork and Quilt StitchingDCarefully sew around the edge of the design Edge of the fabric, and sew using stitchPiecing Patchwork crazy quilt stitchingFor details, refer to Removing the presser foot holder Using the optional quilting guideQuilting ABaste the fabric to be quiltedDSlide the feed dog position lever, located at Free-motion quiltingRfc. Reinforcement **Auto Rfc. Automatic Reinforcement Reinforcement StitchingTriple stretch stitching Bar tack stitchingEPullpossible.down the buttonhole lever as far as Decorative Stitching Fabric.3 FagotingScallop stitching AAttach monogramming foot N BSelect stitchDPull the bobbin threads to create gathers SmockingShell tuck stitching CSew parallel stitching at intervals of 1 cm 3/8 inchJoining Heirloom stitchingDStart sewing Utility stitches Stitch SettingsRfc. Reinforcement Pattern No Rfc Binding Appendix Maintenance Cleaning the machine surfaceCleaning the bobbin case ERemove the bobbin case Grasp the bobbin case, and then pull it outDo not put oil on the bobbin case Troubleshooting Wrong side LowerOr breaks Thread is Tangled onSkipped Fabric isWrinkled Stitches areOperation beep for models equipped with the operation beep Error MessagesNumerics Index31, 34 Page English 885-S38 XE3669-001

HS 2000, EN 1470 specifications

The Brother EN 1470 and HS 2000 are innovative sewing machines that cater to both beginners and experienced sewers alike, offering a host of features and advanced technologies to enhance the sewing experience.

One of the standout features of the Brother EN 1470 is its user-friendly interface, designed with simplicity in mind. This machine offers a wide variety of built-in stitches, allowing users to explore different patterns and styles. With over 100 stitch options, including decorative, utility, and heirloom stitches, the EN 1470 provides immense creative flexibility. The automatic needle threader is another highlight, significantly reducing setup time and enhancing convenience.

The HS 2000, while distinct, shares a similar commitment to usability. It features a robust sewing speed, capable of handling various fabrics, from lightweight materials to heavy-duty textiles. The machine comes equipped with an advanced sewing assist guide, which helps users make quick decisions about settings for specific fabrics and stitch types. Additionally, the HS 2000 has a top-loading bobbin system that simplifies the bobbin change process, ensuring a smooth sewing experience without frustrating interruptions.

Both machines incorporate Brother's advanced technology, including the LED lighting that illuminates the sewing area, allowing for precision work, even in low-light conditions. The ergonomic design also promotes comfortable handling, making lengthy sewing projects less tiring.

Another essential characteristic of the EN 1470 and HS 2000 is their versatility. They accommodate a range of presser feet, which allows for a multitude of sewing techniques such as quilting, zippers, and buttonholes. The built-in buttonhole function is automatic in both models, further simplifying the sewing process while achieving professional results.

Durability is key to the appeal of these machines. Crafted with high-quality materials, they can withstand the demands of regular use. Their compact size and lightweight nature make them portable, perfect for sewing enthusiasts who like to take their work on the go.

In conclusion, the Brother EN 1470 and HS 2000 stand out in the market for their combination of user-friendly features, advanced technologies, and durability. Whether you are a beginner looking to explore the world of sewing or a seasoned professional seeking a reliable machine, both models provide an excellent platform to bring your creative visions to life.
Top Page Image Contents