Brother HS 2000 Useful Sewing Tips, Trial sewing, Changing the sewing direction, Sewing curves

Page 33

USEFUL SEWING TIPS

Various ways to achieve better results for your sewing projects are described below. Refer to these tips when sewing your project.

Trial sewing

After you select a stitch, the machine automatically sets the stitch width and length for the stitch that is selected.

However, a trial piece of fabric should be sewn since, depending on the type of fabric and stitching being sewn, the desired results may not be achieved.

For the trial sewing, use a piece of fabric and thread that are the same as those used for your project, and check the thread tension and stitch length and width. Since the results differ depending on the type of stitching and the number of layers of fabric sewn, perform the trial sewing under the same conditions that will be used with your project.

Changing the sewing direction

aWhen the stitching reaches a corner, stop the sewing machine.

Leave the needle lowered (in the fabric). If the needle was raised, lower the needle either by turning the handwheel toward you (counterclockwise) or by pressing (needle position button) once (for models equipped with the needle position button).

CAUTION

●When using the twin needle, be sure to raise the needle before changing the sewing direction. If the fabric is turned while the needle is lowered, the needle may bend or break.

bRaisefabric.the presser foot lever, and then turn the Turn the fabric using the needle as a pivot.

cLowersewing.the presser foot lever and continue

Sewing curves

2

 

Stop sewing, and then slightly change the sewing direction to sew around the curve.

When sewing along a curve while using a zigzag stitch, select a shorter stitch length in order to obtain a finer stitch.

Sewing thick fabrics

■If the fabric does not fit under the presser foot If the fabric does not fit easily under the presser foot, raise the presser foot lever even higher to bring the presser foot to its highest position.

31

Page 32 Page 34
Image 33
Page 32 Page 34
Contents Computerized Sewing Machine Important Safety Instructions For a longer service life For Users in the UK, EIRE, Malta and Cyprus only For repair or adjustmentContents Utility Stitches Main parts Names of Machine Parts and Their FunctionsNeedle and presser foot section Operation buttonsButtons provided on some models Operation panel Flat bed attachmentASlideopen theit. flat bed attachment to the left to Optional accessories AccessoriesPower supply precautions Using Your Sewing MachineBSet the main power switch to CTo turn off the machine, set the main power switch toFoot controller Changing the needle stop positionSide of stitch selection key Threading the Machine Winding the bobbinETurn on the sewing machine GTrim the excess thread above the bobbin For models equipped with the fast bobbin winding system CSlide the bobbin winder shaft to the rightThread is cut to a suitable length Lower threading For models equipped with the quick-set bobbin Upper threading Thread take-up lever Gthe needle toward the back of the sewing Fully lower the needle threader leverMachine ECatch the thread on the hook as shown belowFor models equipped with the quick-set bobbin Drawing up the lower threadALightly hold the end of the upper thread Bobbin cover should still be removedReplacing the Needle Needle precautionsNeedle types and their uses This section provides information on sewing machine needlesReplacing the needle Checking the needleCorrect needle Incorrect needleInstall the twin needle in the same way Installing the needle clampTwin needle threading Sewing with a twin needleReplacing the presser foot Replacing the Presser FootReplace the presser foot as described below Mark on the wheel points up. With modelsRemoving the presser foot holder Removing the presser foot holderAttaching the presser foot holder ARemove the presser footGeneral sewing procedure Follow the basic procedures below to sewSewing Selecting stitching DIfwidth.necessary, adjust the stitch lengthATurn on the sewing machine CAttach the presser foot indicated in the LCDStarting to sew On the wheel points up. With models equippedBRaise the presser foot lever Sewing reinforcement stitches Thread tensionCorrect tension Upper tension is too tightUpper tension is too loose Thread correctly. For details, refer to page 14Trial sewing Useful Sewing TipsChanging the sewing direction Sewing curvesSewing hook-and-loop fastener Sewing thin fabrics Using a free-arm styleSewing stretch fabrics ASlidereleasetheit.flat bed attachment to the left toRev. Reverse Rfc. Reinforcement Overcasting StitchesAttach overcasting foot G or zigzag foot J Select a stitch For details, refer to Selecting stitchingBasic Stitching FWhen sewing is finished, cut the threadBasic stitching For details, refer to Starting to sewBlind HEM Stitching AReverse the skirt or pantsDFold back the fabric inside along the basting Arm If the needle does not catch the hem fold Buttonhole Sewing Buttonholes can be sewn and buttons can be sewn onAuto Rfc If the button does not fit in the button guide plate Size of the buttonhole is setFPullpossible.down the buttonhole lever as far as Sewing buttonholes on stretch fabrics Button sewingTrim off any excess of the gimp thread CAttach presser foot MWith stitch Select stitch ESelect a stitchAfter sewing for about 10 seconds at low Normally, the feed dog position lever is Positioned atRev. Reverse Zipper InsertionSewing Stretch Fabrics and Elastic Tape Stretch stitchingElastic attaching Appliqués APPLIQUÉ, Patchwork and Quilt StitchingPiecing Edge of the fabric, and sew using stitchPatchwork crazy quilt stitching DCarefully sew around the edge of the designQuilting Using the optional quilting guideABaste the fabric to be quilted For details, refer to Removing the presser foot holderDSlide the feed dog position lever, located at Free-motion quiltingTriple stretch stitching Reinforcement StitchingBar tack stitching Rfc. Reinforcement **Auto Rfc. Automatic ReinforcementEPullpossible.down the buttonhole lever as far as Decorative Stitching Scallop stitching FagotingAAttach monogramming foot N BSelect stitch Fabric.3Shell tuck stitching SmockingCSew parallel stitching at intervals of 1 cm 3/8 inch DPull the bobbin threads to create gathersJoining Heirloom stitchingDStart sewing Utility stitches Stitch SettingsRfc. Reinforcement Pattern No Rfc Binding Appendix Maintenance Cleaning the machine surfaceCleaning the bobbin case ERemove the bobbin case Grasp the bobbin case, and then pull it outDo not put oil on the bobbin case Troubleshooting Or breaks LowerThread is Tangled on Wrong sideWrinkled Fabric isStitches are SkippedOperation beep for models equipped with the operation beep Error MessagesNumerics Index31, 34 Page English 885-S38 XE3669-001

HS 2000, EN 1470 specifications

The Brother EN 1470 and HS 2000 are innovative sewing machines that cater to both beginners and experienced sewers alike, offering a host of features and advanced technologies to enhance the sewing experience.

One of the standout features of the Brother EN 1470 is its user-friendly interface, designed with simplicity in mind. This machine offers a wide variety of built-in stitches, allowing users to explore different patterns and styles. With over 100 stitch options, including decorative, utility, and heirloom stitches, the EN 1470 provides immense creative flexibility. The automatic needle threader is another highlight, significantly reducing setup time and enhancing convenience.

The HS 2000, while distinct, shares a similar commitment to usability. It features a robust sewing speed, capable of handling various fabrics, from lightweight materials to heavy-duty textiles. The machine comes equipped with an advanced sewing assist guide, which helps users make quick decisions about settings for specific fabrics and stitch types. Additionally, the HS 2000 has a top-loading bobbin system that simplifies the bobbin change process, ensuring a smooth sewing experience without frustrating interruptions.

Both machines incorporate Brother's advanced technology, including the LED lighting that illuminates the sewing area, allowing for precision work, even in low-light conditions. The ergonomic design also promotes comfortable handling, making lengthy sewing projects less tiring.

Another essential characteristic of the EN 1470 and HS 2000 is their versatility. They accommodate a range of presser feet, which allows for a multitude of sewing techniques such as quilting, zippers, and buttonholes. The built-in buttonhole function is automatic in both models, further simplifying the sewing process while achieving professional results.

Durability is key to the appeal of these machines. Crafted with high-quality materials, they can withstand the demands of regular use. Their compact size and lightweight nature make them portable, perfect for sewing enthusiasts who like to take their work on the go.

In conclusion, the Brother EN 1470 and HS 2000 stand out in the market for their combination of user-friendly features, advanced technologies, and durability. Whether you are a beginner looking to explore the world of sewing or a seasoned professional seeking a reliable machine, both models provide an excellent platform to bring your creative visions to life.
Top Page Image Contents