Brother EN 1470 Error Messages, Operation beep for models equipped with the operation beep

Page 68

APPENDIX —————————————————————————————————————————————————————

ERROR MESSAGES

If an operation is performed incorrectly before the sewing machine is set up, an error message appears on the operation panel. Follow the instructions indicated in the table.

If you press the stitch selection key or do the operation correctly while the error message is displayed, the message disappears.

Error Message

Probable Cause

Solution

 

 

 

 

The foot controller was pressed (or the start/stop but-

Lower the presser foot lever

 

ton was pressed if the foot controller is not con-

 

before continuing the opera-

 

nected) and the reverse/reinforcement stitch button

 

tion.

 

was pressed while the presser foot is raised.

 

 

 

 

 

 

A stitch other than the buttonhole or bar tack stitch

 

 

was selected and the foot controller was pressed (or

Raise the buttonhole lever

 

the start/stop button was pressed if the foot controller

before continuing the opera-

 

is not connected) while the buttonhole lever is low-

tion.

 

ered.

 

 

The buttonhole or bar tack stitch was selected and

Lower the buttonhole lever

 

the foot controller was pressed (or the start/stop but-

 

before continuing the opera-

 

ton was pressed if the foot controller is not con-

 

tion.

 

nected) while the buttonhole lever is raised.

 

 

 

 

 

 

The reverse/reinforcement stitch button or needle

Move the bobbin winder

 

position button was pressed while the bobbin winder

shaft to the left before con-

 

shaft is moved to the right.

tinuing the operation.

 

 

Disconnect the foot control-

 

The start/stop button was pressed while the foot con-

ler, and then press the start/

 

stop button. Otherwise,

 

troller was connected.

operate the machine by

 

 

 

 

using the foot controller.

 

 

 

 

 

Remove the tangled thread

 

The motor locked up because the thread is tangled.

before continuing the opera-

 

 

tion.

 

 

 

Note

●If error message “F1” through “F8” appears in the LCD while the sewing machine is being used, the machine may be malfunctioning. Contact your nearest authorized service center.

Operation beep (for models equipped with the operation beep)

Each time a key is pressed you will hear one beep. If a non-functioning key is pressed or an incorrect operation is performed you will hear two or four beeps (only for models equipped with the operation beep).

■If a key is pressed (correct operation) One beep sounds.

■If an incorrect operation is performed or a non-functioning key is pressed Two or four beeps sound.

■If the machine locks up, for example, because the thread is tangled

The sewing machine beeps for four seconds and the machine automatically stops. Be sure to check for the cause of the error, and correct it before continuing to sew.

66

Page 67 Page 69
Image 68
Page 67 Page 69
Contents Computerized Sewing Machine Important Safety Instructions For a longer service life For repair or adjustment For Users in the UK, EIRE, Malta and Cyprus onlyContents Utility Stitches Names of Machine Parts and Their Functions Main partsButtons provided on some models Needle and presser foot sectionOperation buttons ASlideopen theit. flat bed attachment to the left to Operation panelFlat bed attachment Accessories Optional accessoriesUsing Your Sewing Machine Power supply precautionsBSet the main power switch to CTo turn off the machine, set the main power switch toSide of stitch selection key Foot controllerChanging the needle stop position ETurn on the sewing machine Threading the MachineWinding the bobbin GTrim the excess thread above the bobbin Thread is cut to a suitable length For models equipped with the fast bobbin winding systemCSlide the bobbin winder shaft to the right Lower threading For models equipped with the quick-set bobbin Upper threading Thread take-up lever Fully lower the needle threader lever Gthe needle toward the back of the sewingMachine ECatch the thread on the hook as shown belowDrawing up the lower thread For models equipped with the quick-set bobbinALightly hold the end of the upper thread Bobbin cover should still be removedNeedle precautions Replacing the NeedleNeedle types and their uses This section provides information on sewing machine needlesChecking the needle Replacing the needleCorrect needle Incorrect needleInstalling the needle clamp Install the twin needle in the same waySewing with a twin needle Twin needle threadingReplacing the Presser Foot Replacing the presser footReplace the presser foot as described below Mark on the wheel points up. With modelsRemoving the presser foot holder Removing the presser foot holderAttaching the presser foot holder ARemove the presser footSewing General sewing procedureFollow the basic procedures below to sew DIfwidth.necessary, adjust the stitch length Selecting stitchingATurn on the sewing machine CAttach the presser foot indicated in the LCDBRaise the presser foot lever Starting to sewOn the wheel points up. With models equipped Thread tension Sewing reinforcement stitchesCorrect tension Upper tension is too tightThread correctly. For details, refer to page 14 Upper tension is too looseUseful Sewing Tips Trial sewingChanging the sewing direction Sewing curvesSewing hook-and-loop fastener Using a free-arm style Sewing thin fabricsSewing stretch fabrics ASlidereleasetheit.flat bed attachment to the left toOvercasting Stitches Rev. Reverse Rfc. ReinforcementAttach overcasting foot G or zigzag foot J Select a stitch For details, refer to Selecting stitchingFWhen sewing is finished, cut the thread Basic StitchingBasic stitching For details, refer to Starting to sewDFold back the fabric inside along the basting Blind HEM StitchingAReverse the skirt or pants Arm If the needle does not catch the hem fold Auto Rfc Buttonhole SewingButtonholes can be sewn and buttons can be sewn on Size of the buttonhole is set If the button does not fit in the button guide plateFPullpossible.down the buttonhole lever as far as Button sewing Sewing buttonholes on stretch fabricsTrim off any excess of the gimp thread CAttach presser foot MESelect a stitch With stitch Select stitchAfter sewing for about 10 seconds at low Normally, the feed dog position lever is Positioned atZipper Insertion Rev. ReverseElastic attaching Sewing Stretch Fabrics and Elastic TapeStretch stitching APPLIQUÉ, Patchwork and Quilt Stitching AppliquésEdge of the fabric, and sew using stitch PiecingPatchwork crazy quilt stitching DCarefully sew around the edge of the designUsing the optional quilting guide QuiltingABaste the fabric to be quilted For details, refer to Removing the presser foot holderFree-motion quilting DSlide the feed dog position lever, located atReinforcement Stitching Triple stretch stitchingBar tack stitching Rfc. Reinforcement **Auto Rfc. Automatic ReinforcementEPullpossible.down the buttonhole lever as far as Decorative Stitching Fagoting Scallop stitchingAAttach monogramming foot N BSelect stitch Fabric.3Smocking Shell tuck stitchingCSew parallel stitching at intervals of 1 cm 3/8 inch DPull the bobbin threads to create gathersDStart sewing JoiningHeirloom stitching Stitch Settings Utility stitchesRfc. Reinforcement Pattern No Rfc Binding Appendix Cleaning the bobbin case MaintenanceCleaning the machine surface Do not put oil on the bobbin case ERemove the bobbin caseGrasp the bobbin case, and then pull it out Troubleshooting Lower Or breaksThread is Tangled on Wrong sideFabric is WrinkledStitches are SkippedError Messages Operation beep for models equipped with the operation beepIndex Numerics31, 34 Page English 885-S38 XE3669-001

HS 2000, EN 1470 specifications

The Brother EN 1470 and HS 2000 are innovative sewing machines that cater to both beginners and experienced sewers alike, offering a host of features and advanced technologies to enhance the sewing experience.

One of the standout features of the Brother EN 1470 is its user-friendly interface, designed with simplicity in mind. This machine offers a wide variety of built-in stitches, allowing users to explore different patterns and styles. With over 100 stitch options, including decorative, utility, and heirloom stitches, the EN 1470 provides immense creative flexibility. The automatic needle threader is another highlight, significantly reducing setup time and enhancing convenience.

The HS 2000, while distinct, shares a similar commitment to usability. It features a robust sewing speed, capable of handling various fabrics, from lightweight materials to heavy-duty textiles. The machine comes equipped with an advanced sewing assist guide, which helps users make quick decisions about settings for specific fabrics and stitch types. Additionally, the HS 2000 has a top-loading bobbin system that simplifies the bobbin change process, ensuring a smooth sewing experience without frustrating interruptions.

Both machines incorporate Brother's advanced technology, including the LED lighting that illuminates the sewing area, allowing for precision work, even in low-light conditions. The ergonomic design also promotes comfortable handling, making lengthy sewing projects less tiring.

Another essential characteristic of the EN 1470 and HS 2000 is their versatility. They accommodate a range of presser feet, which allows for a multitude of sewing techniques such as quilting, zippers, and buttonholes. The built-in buttonhole function is automatic in both models, further simplifying the sewing process while achieving professional results.

Durability is key to the appeal of these machines. Crafted with high-quality materials, they can withstand the demands of regular use. Their compact size and lightweight nature make them portable, perfect for sewing enthusiasts who like to take their work on the go.

In conclusion, the Brother EN 1470 and HS 2000 stand out in the market for their combination of user-friendly features, advanced technologies, and durability. Whether you are a beginner looking to explore the world of sewing or a seasoned professional seeking a reliable machine, both models provide an excellent platform to bring your creative visions to life.
Top Page Image Contents