Brother 855-X06 operation manual Controls, Pattern selection dial, Stretch stitching

Page 10

KNOWING YOUR SEWING MACHINE—————

5Lower the presser foot lever and fix the presser foot onto the shank. If the presser foot is in the correct place, the bar should snap in.

1 2

1Shank

2 Bar

Presser foot installation orientation

CAUTION

If the presser foot is not installed with the correct orientation, the needle may strike the presser foot, which may bend or break the needle and cause injury.

THE CONTROLS

Pattern selection dial

CAUTION

When you use the pattern selection dial to choose a pattern, raise the needle by turning the handwheel toward you (counterclockwise) so that the mark on the wheel points up. If the needle is in the down position when you turn the pattern selection dial, the needle, presser foot or fabric may be damaged.

To choose a stitch, simply turn the pattern selection dial in either direction. The next section shows recommended stitch lengths and widths.

2

1

1Pattern selection dial

2 Chosen pattern number

Stretch stitching

Raise the needle by turning the handwheel toward you (counterclockwise) so that the mark on the wheel points up.

Setting the stitch length dial to “ ” changes the selected pattern to a stretch stitch.

9

Image 10
Contents Sewing Machine Important Safety Instructions Save These Instructions Contents Knowing Your Sewing Machine AccessoriesOptional accessories Part Name Part Code Americas OthersMain Parts Flat bed attachmentConnecting plugs Using Your Sewing MachineConnect the foot controller plug to the machine Checking the needle Main power and sewing light switchFoot controller Replacing the needleChanging the presser foot Pattern selection dial Presser foot installation orientationControls Stretch stitchingStitches Patterns and stitch namesStitches Only available on certain models Pattern Stitch Name Recommended0-3/16 Fixed Stitch length dial Stitch width dialReverse sewing lever Threading the MachineWinding the bobbin Pull up the spool pin and put a spool of thread on this pin Turn on the machineInstall the bobbin wound with thread Lower threadingLower threading for models equipped with a quick-set bobbin Groove ProjectionUpper threading Turn off the machine Raise the presser foot lever GuideNeedle holder Needle threader lever Pull the thread through the needle For models equipped with a quick-set bobbin Drawing up the lower threadPull on the upper thread to draw up the lower thread Replace the bobbin coverTransparent nylon thread FABRIC, THREAD, and Needle CombinationsBall point needle Fabric Type/Application Thread Size of NeedlePlease read before sewing Sewing BasicsStarting sewing Changing the sewing Direction Trial sewingSewing thick fabrics Stitching cylindrical pieces Sewing thin fabricsSewing stretch fabrics Sewing with a twin needle OptionThread the left needle Attaching the extra spool pinSelect a stitch Thread the right needleCorrect tension Thread tensionUpper tension is too loose Upper tension is too tightZigzag stitching BUILT-IN StitchesStraight stitching Blind hem stitchingFold the fabric along the desired edge of the hem, and press Elastic stitching Adjust the thread tension so that it is tighter than normalSew at a slow speed Joining fabric Double action stitchingFagoting Set the stitch width toPattern Stitch Overedge stitchingStitch Decorative stitching Feather stitchingTriple zigzag stretch stitching Stitch Name PatternMaking a buttonhole Sewing Buttonholes and ButtonsMaking a buttonhole 1-step automatic buttonhole Openbutton.the button plate and insertYou need to sew the front bar tack first If the button does not fit in the button guide plateLower the buttonhole lever and push it back slightly Follow steps 1 to 6 from Making a buttonhole on Adjusting buttonholesMaking a buttonhole on stretch fabrics Piece of fabric to observe how Material is fedThen tie it with the bobbin thread Sewing buttonsAt a slow speed, sew about 10 stitches Any Sewing DarningZipper insertion Using Attachments and ApplicationsWhen you have finished sewing, remove the basting stitching Prepare the fabric with the zipper basted on the wrong sideAppliqués GatheringDarning Baste the cut design to the fabricWhen edge stitching Turn off the machine Optional AccessoriesUsing the blind stitch foot When sewing seams Turn off the machineCleaning MaintenancePrecautions on storing the machine AppendixInstall the needle plate, and then tighten the screws Troubleshooting Symptom Possible cause How to put it rightThread is Thread BreaksLower Tangled orNot be used Stitches are SkippedThreader can Stitch isIndex NumericsEnglish