Brother 855-X06 operation manual Save These Instructions

Page 3

———————

Keep fingers away from all moving parts. Special care is required around the machine needle.

Switch the machine to the symbol “O” position to turn it off when making any adjustments in the needle area.

Do not use a damaged or incorrect needle plate, as it could cause the needle to break.

Do not push or pull the fabric when sewing, and follow careful instruction when freehand stitching so that you do not deflect the needle and cause it to break.

6 This machine is not a toy:

Your close attention is necessary when the machine is used by or near children.

The plastic bag that this machine was supplied in should be kept out of the reach of children or disposed of.

Never allow children to play with the bag due to the danger of suffocation.

Do not use outdoors.

7 For a longer service life:

When storing this machine, avoid direct sunlight and high humidity locations. Do not use or store the machine near a space heater, iron, halogen lamp, or other hot objects.

Use only neutral soaps or detergents to clean the case. Benzene, thinner, and scouring powders can damage the case and machine, and should never be used.

Always consult the operation manual when replacing or installing any assemblies, the presser feet, needle, or other parts to assure correct installation.

8 For repair or adjustment:

If the Light unit (light-emitting diode) is damaged, it must be replaced by authorized dealer.

In the event a malfunction occurs or adjustment is required, first follow the

troubleshooting table in the back of the operation manual to inspect and adjust the machine yourself. If the problem persists, please consult your local authorized Brother dealer.

Use this machine only for its intended use as described in this manual.

Use accessories recommended by the manufacturer as contained in this manual.

The contents of this manual and specifications of this product are subject to change without notice.

For additional product information, visit our web site at www.brother.com

SAVE THESE

INSTRUCTIONS

This machine is intended

for household use.

This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.

Children should be supervised to ensure that they do not play with the appliance.

FOR USERS IN THE UK, EIRE, MALTA AND CYPRUS ONLY

IMPORTANT

In the event of replacing the plug fuse, use a fuse

approved by ASTA to BS 1362, i.e. carrying the mark, rating as marked on plug.

Always replace the fuse cover. Never use plugs with the fuse cover omitted.

If the available electrical outlet is not suitable for the plug supplied with this equipment, you should contact your authorized dealer to obtain the correct lead.

2

Image 3
Contents Sewing Machine Important Safety Instructions Save These Instructions Contents Part Name Part Code Americas Others AccessoriesOptional accessories Knowing Your Sewing MachineFlat bed attachment Main PartsUsing Your Sewing Machine Connecting plugsConnect the foot controller plug to the machine Replacing the needle Main power and sewing light switchFoot controller Checking the needleChanging the presser foot Stretch stitching Presser foot installation orientationControls Pattern selection dialPattern Stitch Name Recommended Patterns and stitch namesStitches Only available on certain models Stitches0-3/16 Fixed Stitch width dial Stitch length dialThreading the Machine Reverse sewing leverWinding the bobbin Turn on the machine Pull up the spool pin and put a spool of thread on this pinLower threading Install the bobbin wound with threadGroove Projection Lower threading for models equipped with a quick-set bobbinUpper threading Guide Turn off the machine Raise the presser foot leverNeedle holder Needle threader lever Pull the thread through the needle Replace the bobbin cover Drawing up the lower threadPull on the upper thread to draw up the lower thread For models equipped with a quick-set bobbinFabric Type/Application Thread Size of Needle FABRIC, THREAD, and Needle CombinationsBall point needle Transparent nylon threadSewing Basics Please read before sewingStarting sewing Trial sewing Changing the sewing DirectionSewing thick fabrics Sewing with a twin needle Option Sewing thin fabricsSewing stretch fabrics Stitching cylindrical piecesThread the right needle Attaching the extra spool pinSelect a stitch Thread the left needleUpper tension is too tight Thread tensionUpper tension is too loose Correct tensionBlind hem stitching BUILT-IN StitchesStraight stitching Zigzag stitchingFold the fabric along the desired edge of the hem, and press Adjust the thread tension so that it is tighter than normal Elastic stitchingSew at a slow speed Set the stitch width to Double action stitchingFagoting Joining fabricOveredge stitching Pattern StitchStitch Stitch Name Pattern Feather stitchingTriple zigzag stretch stitching Decorative stitchingOpenbutton.the button plate and insert Sewing Buttonholes and ButtonsMaking a buttonhole 1-step automatic buttonhole Making a buttonholeIf the button does not fit in the button guide plate You need to sew the front bar tack firstLower the buttonhole lever and push it back slightly Piece of fabric to observe how Material is fed Adjusting buttonholesMaking a buttonhole on stretch fabrics Follow steps 1 to 6 from Making a buttonhole onAny Sewing Darning Sewing buttonsAt a slow speed, sew about 10 stitches Then tie it with the bobbin threadPrepare the fabric with the zipper basted on the wrong side Using Attachments and ApplicationsWhen you have finished sewing, remove the basting stitching Zipper insertionBaste the cut design to the fabric GatheringDarning AppliquésWhen sewing seams Turn off the machine Optional AccessoriesUsing the blind stitch foot When edge stitching Turn off the machineAppendix MaintenancePrecautions on storing the machine CleaningInstall the needle plate, and then tighten the screws Symptom Possible cause How to put it right TroubleshootingTangled or Thread BreaksLower Thread isStitch is Stitches are SkippedThreader can Not be usedNumerics IndexEnglish