Brother 855-X06 operation manual Threading the Machine, Reverse sewing lever, Winding the bobbin

Page 14

KNOWING YOUR SEWING MACHINE—————

CAUTION

●After adjusting the stitch width, slowly turn the handwheel toward you (counterclockwise) and check that the needle does not touch the presser foot. If the needle hits the presser foot, the needle may bend or break.

●If the stitches are bunched together, increase the stitch length. Continuing to sew with the stitches bunched together may result in the needle bending or breaking.

Reverse sewing lever

You can use reverse sewing for back tacking and reinforcing seams.

To sew in reverse, push the reverse sewing lever in as far as possible and hold it in that position while you lightly push the foot controller. To sew forward, release the reverse sewing lever. The machine will then sew forward.

1

1 Reverse sewing lever

THREADING THE MACHINE

Winding the bobbin

CAUTION

●We designed the bobbin that comes with this machine. If you use bobbins from other models, the machine will not work properly. Only use the bobbin that comes with this machine or bobbins of the same type (part code: SA156, SFB: XA5539-151). Using other bobbins may cause damage to the machine.

Actual size

11.5mm (7/16 inch)

This model	Other models

13

Image 14

Contents Sewing Machine Important Safety Instructions Save These Instructions Contents Knowing Your Sewing Machine AccessoriesOptional accessories Part Name Part Code Americas OthersMain Parts Flat bed attachmentConnect the foot controller plug to the machine Using Your Sewing MachineConnecting plugs Checking the needle Main power and sewing light switchFoot controller Replacing the needleChanging the presser foot Pattern selection dial Presser foot installation orientationControls Stretch stitchingStitches Patterns and stitch namesStitches Only available on certain models Pattern Stitch Name Recommended0-3/16 Fixed Stitch length dial Stitch width dialWinding the bobbin Threading the MachineReverse sewing lever Pull up the spool pin and put a spool of thread on this pin Turn on the machineInstall the bobbin wound with thread Lower threadingLower threading for models equipped with a quick-set bobbin Groove ProjectionUpper threading Turn off the machine Raise the presser foot lever GuideNeedle holder Needle threader lever Pull the thread through the needle For models equipped with a quick-set bobbin Drawing up the lower threadPull on the upper thread to draw up the lower thread Replace the bobbin coverTransparent nylon thread FABRIC, THREAD, and Needle CombinationsBall point needle Fabric Type/Application Thread Size of NeedleStarting sewing Sewing BasicsPlease read before sewing Sewing thick fabrics Trial sewingChanging the sewing Direction Stitching cylindrical pieces Sewing thin fabricsSewing stretch fabrics Sewing with a twin needle OptionThread the left needle Attaching the extra spool pinSelect a stitch Thread the right needleCorrect tension Thread tensionUpper tension is too loose Upper tension is too tightZigzag stitching BUILT-IN StitchesStraight stitching Blind hem stitchingFold the fabric along the desired edge of the hem, and press Sew at a slow speed Adjust the thread tension so that it is tighter than normalElastic stitching Joining fabric Double action stitchingFagoting Set the stitch width toStitch Overedge stitchingPattern Stitch Decorative stitching Feather stitchingTriple zigzag stretch stitching Stitch Name PatternMaking a buttonhole Sewing Buttonholes and ButtonsMaking a buttonhole 1-step automatic buttonhole Openbutton.the button plate and insertLower the buttonhole lever and push it back slightly If the button does not fit in the button guide plateYou need to sew the front bar tack first Follow steps 1 to 6 from Making a buttonhole on Adjusting buttonholesMaking a buttonhole on stretch fabrics Piece of fabric to observe how Material is fedThen tie it with the bobbin thread Sewing buttonsAt a slow speed, sew about 10 stitches Any Sewing DarningZipper insertion Using Attachments and ApplicationsWhen you have finished sewing, remove the basting stitching Prepare the fabric with the zipper basted on the wrong sideAppliqués GatheringDarning Baste the cut design to the fabricWhen edge stitching Turn off the machine Optional AccessoriesUsing the blind stitch foot When sewing seams Turn off the machineCleaning MaintenancePrecautions on storing the machine AppendixInstall the needle plate, and then tighten the screws Troubleshooting Symptom Possible cause How to put it rightThread is Thread BreaksLower Tangled orNot be used Stitches are SkippedThreader can Stitch isIndex NumericsEnglish