Brother 855-X06 operation manual Pull the thread through the needle

Page 21

———————

1Needle holder

2Needle threader lever

3 Guide

5Pull down the needle threader lever as much as possible, and then turn the lever toward the back of the machine (away from you). Make sure that the hook passes through the eye of the needle and grabs the thread.

1 2

1Hook

2 Thread

•Hold the thread in front of the needle to make sure that the hook grabs it.

6While lightly holding the thread, turn the needle threader lever toward the front of

the machine (toward you). The hook will	1
pull the thread through the needle.

7Raise the needle threader lever.

8Pull the loop of the thread passed through the eye of the needle toward the rear of the machine.

1Loop of thread

CAUTION

●Be careful not to pull on the thread with force or it may bend the needle.

●If the thread does not pass through the eye of the needle, start from step 3 again.

9Raise the presser foot lever.

Image 21

Contents Sewing Machine Important Safety Instructions Save These Instructions Contents Optional accessories AccessoriesKnowing Your Sewing Machine Part Name Part Code Americas OthersFlat bed attachment Main PartsUsing Your Sewing Machine Connecting plugsConnect the foot controller plug to the machine Foot controller Main power and sewing light switchChecking the needle Replacing the needleChanging the presser foot Controls Presser foot installation orientationPattern selection dial Stretch stitchingStitches Only available on certain models Patterns and stitch namesStitches Pattern Stitch Name Recommended0-3/16 Fixed Stitch width dial Stitch length dialThreading the Machine Reverse sewing leverWinding the bobbin Turn on the machine Pull up the spool pin and put a spool of thread on this pinLower threading Install the bobbin wound with threadGroove Projection Lower threading for models equipped with a quick-set bobbinUpper threading Guide Turn off the machine Raise the presser foot leverNeedle holder Needle threader lever Pull the thread through the needle Pull on the upper thread to draw up the lower thread Drawing up the lower threadFor models equipped with a quick-set bobbin Replace the bobbin coverBall point needle FABRIC, THREAD, and Needle CombinationsTransparent nylon thread Fabric Type/Application Thread Size of NeedleSewing Basics Please read before sewingStarting sewing Trial sewing Changing the sewing DirectionSewing thick fabrics Sewing stretch fabrics Sewing thin fabricsStitching cylindrical pieces Sewing with a twin needle OptionSelect a stitch Attaching the extra spool pinThread the left needle Thread the right needleUpper tension is too loose Thread tensionCorrect tension Upper tension is too tightStraight stitching BUILT-IN StitchesZigzag stitching Blind hem stitchingFold the fabric along the desired edge of the hem, and press Adjust the thread tension so that it is tighter than normal Elastic stitchingSew at a slow speed Fagoting Double action stitchingJoining fabric Set the stitch width toOveredge stitching Pattern StitchStitch Triple zigzag stretch stitching Feather stitchingDecorative stitching Stitch Name PatternMaking a buttonhole 1-step automatic buttonhole Sewing Buttonholes and ButtonsMaking a buttonhole Openbutton.the button plate and insertIf the button does not fit in the button guide plate You need to sew the front bar tack firstLower the buttonhole lever and push it back slightly Making a buttonhole on stretch fabrics Adjusting buttonholesFollow steps 1 to 6 from Making a buttonhole on Piece of fabric to observe how Material is fedAt a slow speed, sew about 10 stitches Sewing buttonsThen tie it with the bobbin thread Any Sewing DarningWhen you have finished sewing, remove the basting stitching Using Attachments and ApplicationsZipper insertion Prepare the fabric with the zipper basted on the wrong sideDarning GatheringAppliqués Baste the cut design to the fabricUsing the blind stitch foot Optional AccessoriesWhen edge stitching Turn off the machine When sewing seams Turn off the machinePrecautions on storing the machine MaintenanceCleaning AppendixInstall the needle plate, and then tighten the screws Symptom Possible cause How to put it right TroubleshootingLower Thread BreaksThread is Tangled orThreader can Stitches are SkippedNot be used Stitch isNumerics IndexEnglish

pull the thread through the needle.