Kenmore 625.385200 manual Tank Light, Press Select again to display the Recharge Days screen

Page 19

Controller Features

6.Press SELECT again to display the “Gallons or Liters” screen.

8.Press SELECT again to display the “Backwash Time” setting screen.

Figure 31

GALLON OR LITER READINGS: Water usage and flow rate displays are shown in gallons at the default setting. If you prefer liters, change this setting from “Gals” to “Liter” by pressing the r UP button.

7.Press SELECT again to display the “Recharge Days” screen.

Figure 33

BACKWASH & FAST RINSE TIMES: If you experience salty tasting water after regeneration, you may need to increase the backwash and fast rinse times. The default backwash time is 13 minutes and the default fast rinse time is 6 minutes. However, you may increase or decrease the backwash and fast rinse times, in 1 minute increments.

If you wish to change the backwash time, use the r UP or s DOWN buttons to set the backwash time between 1 and 30 minutes. Then press SELECT to display the “Fast Rinse Time” setting screen.

Figure 32

MAXIMUM DAYS BETWEEN REGENERATIONS: The electronic controller automatically determines regen- eration frequency. This provides the greatest operat- ing efficiency and, under most conditions this feature will be left in its default mode. However, you can set this feature to force a regeneration every set number of days. You may want to do this if, for example, your water supply contains iron and you want the softener to regenerate at least once every few days to keep the resin bed clean. Use the r UP or s DOWN buttons to change the number of days (up to 15). If no change is desired, continue to next step.

Figure 34

If you wish to change the fast rinse time, use the r UP or s DOWN buttons to set the fast rinse time between 1 and 30 minutes.

9.Press SELECT to return to the normal run (time of day) screen.

TANK LIGHT

A light inside the salt storage tank will come on when- ever you open the salt lid. A “Tank Light” icon is dis- played when this light is on. The light turns off when you close the salt lid. It will also turn off automatically after 15 minutes if the salt lid is left open.

Tank Light

Icon

Figure 35

Questions? Call the Kenmore Water Line 1-800-426-9345 or visit www.kenmorewater.com

19

Image 19
Contents Hybrid Water Softener Warranty on Kenmore Elite Hybrid Water Softener WarrantySafety Guides Table of ContentsSpecifications Specifications & Performance ClaimsChlorine ±10% mg/L 50% DimensionsPerformance Claims Barium 10 ±10% mg/L Mg/L Radium 226/228 25 pCi/L PCi/LPacking List Plan Your InstallationOutside Faucet Hard water LineCheck Your Water Pressure Before Installing InstallationBypass Valve or Plastic Clip Alternate Bypass Valve InstallationBypass valve with a wet rag Ring Incoming Hard Water Connect the Valve Drain Hose Rinse OUT Carbon Fines Install CoversConnect to Electrical Power Metal Pipe GroundingValve Bypass Leak TestRestart the Water Heater Single Bypass ValveSET Present Time of DAY Programming the SoftenerBlue Light Program the SoftenerSET Salt Type SET Water Hardness NumberWater Softening Salt with Iron Removing Additives Flushing the SystemAdding Salt to the Storage Tank Adding Salt to the Storage TankRecharge NOW Controller FeaturesWhat Your Hybrid Water Softener Will Do Extra RechargeSalt Monitor System Optional Settings = Salt Efficiency = Clean FeaturePress Select again to display the 12 or 24 hr screen Tank Light Icon Tank LightPress Select again to display the Recharge Days screen Press Select to return to the normal run time of day screenWater Flow Through the Softener Recharge Time Remaining & Valve Position IndicatorsProgram Memory Tener Service InformationCare of Your Water Softener Salt BridgeProblem Cause Correction TroubleshootingResetting to Factory Defaults Manually Initiated Electronic DiagnosticsPosition Markers valve in service Wiring Schematic Water Softener Exploded View Softener Parts List Valve Assembly Exploded View Valve Parts List Page Model For Iowa USE onlyGet it fixed, at your home or ours