Specifications & Performance Claims
This model is efficiency rated. The efficiency rating is valid only at the minimum salt dose. The softener has a demand initiated regeneration (D.I.R) feature that complies with specific performance specifications intended to mini- mize the amount of regenerant brine and water used in its operation.
This softener has a rated softener efficiency of not less than 3,350 grains of total hardness exchange per pound of salt (based on sodium chloride) and shall not deliver more salt than its listed rating or be operated at a sustained maxi- mum service flow rate greater than its listed rating. This softener has been proven to deliver soft water for at least ten continuous minutes at the rated service flow rate. The rated salt efficiency is measured by laboratory tests described in NSF/ANSI Standard 44. These tests represent the maximum possible efficiency that the system can achieve. Operational efficiency is the actual efficiency after the system has been installed. It is typically less than the rated efficiency, due to individual application factors including water hardness, water usage, and other contaminants that reduce a softener's capacity.
While testing was performed under standard laboratory conditions, actual performance of the system may vary based on local water conditions. This system has been tested according to NSF/ANSI Standard 42 for the reduction of chlorine taste and odor. The concentration of the indicated substance in water entering the system was reduced to a concentration less than or equal to the permissible limit for water leaving the system, as specified in NSF/ANSI Standard 42.
SPECIFICATIONS
|
|
|
|
|
|
| Model No. 625.385200 |
Model Code |
|
| 520 |
Rated Softening Capacity (Grains @ Salt Dose) |
|
| 11,000 @ 2.6 lbs. |
|
| 24,700 @ 7.8 lbs. | |
|
|
| 31,100 @ 13.4 lbs. |
Rated Efficiency (Grains/Pound of Salt @ Minimum Salt Dose) | 4,230 @ 2.6 lbs. | ||
Water Used During Regeneration @ Minimum Salt Dose | 5.0 gallons/1,000 grains | ||
Total Water Used Per Regeneration @ Maximum Salt Dose | 54.7 gallons | ||
Rated Service Flow Rate |
|
| 8.0 gpm |
Amount of High Capacity Ion Exchange Resin |
|
| 0.98 cu. ft. |
Pressure Drop at Rated Service Flow |
|
| 6.5 psig |
Water Supply Max. Hardness |
|
| 100 gpg |
Water Supply Max. Clear Water Iron |
|
| 3 ppm* |
Water Pressure Limits (minimum / maximum) |
|
| 20 - 125 psi |
Water Temperature Limits (minimum / maximum) |
|
| 40 - 120 °F |
Minimum Water Supply Flow Rate |
|
| 3 gpm |
Intermittent Flow @ 15 psi |
|
| 13.7 gpm** |
Maximum Drain Flow Rate |
|
| 2.0 gpm |
| 0.50 ppm | 2,280,000 gal.§ | |
| 0.75 ppm | 1,520,000 gal.§ | |
Rated Capacity at Chlorine Concentration*** of: 1.0 | ppm | 1,140,000 gal.§ | |
| 1.5 | ppm | 760,000 gal.§ |
| 2.0 | ppm | 570,000 gal.§ |
*Capacity to reduce clear water iron is substantiated by WQA test data. State of Wisconsin requires additional treatment if water supply contains clear water iron exceeding 5 ppm.
**Intermittent flow rate does not represent the maximum service flow rate used for deter- mining the softener’s rated capacity and efficiency. Continuous operation at flow rates greater than the service flow rate may affect capacity and efficiency performance.
***Typical residential chlorine concentration is 0.5 to 1.0 ppm. §From independent laboratory test data.
This system conforms to NSF/ANSI Standards 42 & 44 for the specific performance claims as verified and substantiated by test data.
Variable Salt Dose: The salt dose is selected by the electronic controls at regeneration time based on the amount needed.
Questions? Call the Kenmore Water Line
4