Kenmore 625.38826 Faceplate Timer Features, Manually, Recharge, Salt Monitor System, Level

_iiii_i_ii_i SECTION2 _J_J_J:,_:,_] HOW YOUR WATER SOFTENER WORKS

A. FACEPLATE TIMER FEATURES

S	• EXTRA RECHARGE
	Sometimes,			a	manually		started
	regeneration				(recharge)		may	be
	desired,		or	needed.		Two	exam-
C	ples	are:
	- You have used more water than
T
	usual	(guests		visiting)		and you
	may	run	out		of soft water		before
	the	next	timer		started	regenera-
	tion.
	- You did not refill the softener
	with salt before it was gone. After
N	you	refill	with		salt:
	You	can start			a regeneration		right
	away, or		you		can set	the	timer	to

JJJJJJJJJJJJJJJJ.regenerate at the next 2:00 AM (or

J_JJJJJJJJJJJ_JJJ
JJ	JJJJ_JJJJ_	other	preset	recharge	time).	Do

JJJJJJJJJ_J

JJJ_JJJJJJJJ

J_	_JJJJJJJJ_	the following.
JJJJJ _JJJ_JJ_J_JJJJJJJJJ_ _

JJ_J_JJ

JJ_JJJJJ_JJ

JJJ_JJJJJJJJJJ_J_

JJJJ_JJ_JJ_JJ_JJ

Press the ON/OFF-HOLD			but-	;
•	RECHARGE	NOW		"'_' _ "_'_1
ton	and hold until	*RECHARGE,		',

Serv and Fill begin to flash in the display. Upon

reaching fill, the first cycle of regeneration, the flash- ing Serv goes off and Fill is on steady. RECHARGE

continues to flash. This regeneration will last for about 2 hours. After the 2 hours, you will have soft water again.

*Note:

If the CLEAN feature is set to ON, a cleaning back- wash (CLEAN and Bkwsh or Rinse flashes in the dis-

play, along with the minutes of the clean cycle re-

maining) precedes the recharge.

• SALT MONITOR SYSTEM

The face plate timer has a low salt monitor with an

indicator light to remind you to refill the storage

tank with salt. To set this monitor system:

_Lift

the

salt

hole

cover

and

level the

salt in the

storage

tank.

m The salt level decal,

on

the

brineweU

inside

the

tank,

has

numbers

from

0

to 8

(see

drawing

be-

low). Observe the number the leveled salt is at

or closest

to.

_I

Now,

press

the

SALT

LEVEL

ADJUST

button

until black bars display up to the salt level num-

ber.

For

example,

the

pictures

below

show

the

salt

level

at

6.

_

Finally,

set

the level

you

want

the

low

salt

indi-

cator light to come on. Press the SIGNAL LIGHT

ADJUST button until a (÷) shows opposite this

number.

In

the

example

below,

the

light

will

come on when the stored salt drops to level 2. At

level 2, the storage tank is about 1/3 full. This is

the lowest you should allow the stored salt level

to drop to (see note on page 1-6).

_

If you

wish

to turn

the

salt

monitor

off,

press

the

SIGNAL

LIGHT

ADJUST

button

until

OFF

shows

above.

Note:

Your salt monitor is an estimate of your salt level; ac-

curacy depends on the type of salt used and other

regeneration characteristics.

LEVEL u_V_

bars, salt SALT

level LEVEL8

brinewell

11116

• RECHARGE	TONIGHT	i	/.uo /
Press and release	(do not hold) the	_,_	_o.,o.

ON / OFF-HOLD button. RE-

CHARGE TONIGHT flashes in the display, and the

softener begins regeneration at the next preset re- charge time. Press and release the ON/OFF-HOLD button once more if you decide to cancel the regen-

eration, and RECHARGE TONIGHZ

	_4
decal	_ 3
salt	12_
level
	_13($
TONIGHT
RECHARGERECI
NOW
indicator light	LOW
	SALT

2-1

Problems, Questions? Call 1-800-426-9345 Kenmore Water Line