Kenmore 625.38827, 625.38826 Maximum Days Between REGENERA- Tions and 12 / 24 Hour Clock

Page 11

A. FACEPLATE TIMER FEATURES

_1_ OPTIONAL SETTINGS - SALT EFFICIENCY,

CLEAN FEATURE, CLEAN FEATURE MINUTES,

MAXIMUM DAYS BETWEEN REGENERA- TIONS and 12 / 24 HOUR CLOCK:

1.To set any of the following options, press and hold SELECT for 3 seconds until 000 shows in the display.

Then press once until the SALT EFFICIENCY dis-

play shows. Use the UP / Down buttons to change the ON / OFF displays.

OFF

o

_SALTEFFICIENCY'OWhen this feature is ON, the unit will operate at salt efficiencies of 4000 grains

of hardness per pound of salt or higher, which will reduce the softeners salt usage. (May recharge more often using smaller salt dosage and less water).

2. Press SELECT again to show the CLEAN display.

UFF

_CLEAN: This feature is beneficial on water sup-

plies containing iron and/or high amounts of sedi- ments (sand, silt, dirt, etc.). When set to ON, a back- wash and fast rinse cycle will occur first, preceeding

the normal regeneration sequence (see page 2-4).

This provides extra cleaning of the resin bed before

it is regenerated with the salt brine. To conserve wa-

ter, if your water supply does not contain iron or

sediments, be sure this feature is set to OFF.

3.Press SELECT again until the CLEAN TIME dis- play shows.

_es

example: time set to 3 minutes

_CLEANfeature minutes: If you are using this fea-

ture, the length of the extra backwash cycle auto-

matically sets to 7 (9minutes on UltraSoft 250) min-

utes. However, you can adjust this time from I to 15

minutes in length. To change this cycle time, use the UP button to increase the time, or the DOWN button

to shorten the time. If no change is desired, continue below.

2-2

4.Press SELECT again to show the following RE-

CHARGE display.

RECHARG£_t

default display

example: set to

4 days maxi-

 

mum between

regenerations

_Maximum days between regenerations: The face-

plate timer automatically controls regeneration fre-

quency (see page 2-5). This provides the greatest operating efficiency, and under most conditions this

feature will be left in its default mode. However, you can modify this feature if you want to force a

regeneration every set number of days. For exam-

ple, if your water supply contains iron and you

want the softener to regenerate at least once every few days to keep the resin bed clean, set the display as typically shown above. Setting is available from 1 to 15 days by using the UP and DOWN buttons.

5.Press SELECT to show the 12 HOUR display.

_12

or

24

hour

clock:

All

time

I

J

displays

are shown in

standard

clock

time

(1 to

12 PM;

and

1 to

12 AM) at the 12 hr default set-

 

 

ting. If military time displays are

 

 

desired,

set to 24 hr by

pressing

 

riME

the UP

button.

 

 

 

 

 

6.Press SELECT to return to the present time dis- play.

WATER FLOW THROUGH THE SOFTENER

If soft water is in use, the water

flow bars continually scroll

across the display. The bars scroll slowly when water flow is slow, and move faster as water flow increases. The flow bars do not show when all faucets and

water using appliances are off.

=i 2,3B"

Flow bars scroll when I_,; { _LQ"_ _"

SOft water is in use

_==1,:_

Problems, Questions? Call 1- 800- 426- 9345 Kenmore Water Line

Page 10 Page 12
Image 11
Page 10 Page 12
Contents Owners Manual Facts and Figures to Keep Sears Residential Water SoftenerAbout Your Water Softener Safety Guides Inside Check List of STEP-BY-STEP Guides to InstallNumbers Referred Unless OtherwiseSET Present Time of DAY Program the TimerPress the Select button once again, to com SET Water Hardness NumberGpg hardness All Sanitize the Water SoftenerWater Softening Salt with Iron Removing Fill the Storage Tank with SaltSee Salt Monitor System Faceplate Timer FeaturesManually RechargeWater Flow Through the Softener Maximum Days Between REGENERA- Tions and 12 / 24 Hour ClockMinutes Position IndicatorsError Code Recharge Time Remaining and ValveWater Flow Through Softener in Fill ServiceWater Flow Through Softener in Service RegenerationBackwash Water Flow Through Softener in BackwashWater Flow Through the Softener Brining and Brine Rinse Water Flow Through Softener in Fast RinseElectronics Automatic BypassSalt Bridge When to Refill with SaltSalt Refilling Storage TANK, Salt Bridge Salt BridgeIron from Resin BED Keeping the Water Softener CleanCleaning Nozzle & Venturi Nozzle & VenturiLay a Protect the Water Softener from FreezingBrine valve Drain All Water From SoftenerProblem Checklist ... to Help YOU Save MoneyKnow about Your Water Softener Dimensions / SpecificationsUltraSoft 250 7UlSof,75Vance Regeneration Check TroubleshootingAlways Make These Initial Checks First Possible Defect Code Automatic Electronic DiagnosticsManual Initiated Electronics Diagnostics Electronic ComponentsJJlONI Brining Manual Advance Regeneration CheckCycle Flow Rates Gallons PER MIN UltraSoftLieve Pressure Rotary Valve ServiceDisassembly AssemblyFill Cycle Water Flow Through the Softener ValveSection Water Flow Through the Softener Valve Fast Rinse Cycle Iiii JJJl Repair Parts for Water Softener KEY Part Description NO. Number Water Softener CompleteInlet Outlet Grounding Clamps 41 7080653 Clip 42 7131365 Screen Brine Valve AssemblyIiiii I KEY Part Description Number Valve AssemblyBypass Installation Valve Sears

625.38827, 625.38826 specifications

The Kenmore 625.38826 and 625.38827 are highly regarded models in the Kenmore line of water filtration systems, known for their efficiency, advanced features, and reliable performance. Designed for household use, these systems cater to the growing need for cleaner, healthier drinking water.

One of the standout features of the Kenmore 625.38826 and 625.38827 is their multi-stage filtration process. Each unit utilizes a combination of sediment filters, activated carbon filters, and advanced membrane technology. This filtration system effectively removes contaminants such as chlorine, lead, mercury, and other impurities, ensuring that the water you consume is of the highest quality. The filters are easy to replace, allowing for seamless maintenance and continued performance.

Both models are equipped with a user-friendly LCD display that provides real-time information about the status of the filtration system. This feature includes alerts for filter replacement, making it easier to maintain the unit and ensure that your water stays clean. The display also tracks water consumption, helping users manage their usage and ensure efficiency.

In terms of capacity, the Kenmore 625.38826 and 625.38827 can accommodate the needs of a typical household, with sufficient production rates to support daily hydration and cooking needs. Additionally, these models have been designed with energy efficiency in mind, reducing power consumption without compromising performance.

The build quality of these systems is also noteworthy. Both models feature durable enclosures that resist corrosion and wear, ensuring longevity even in high-demand environments. Their compact design allows for easy installation under kitchen sinks, making them an unobtrusive addition to any home.

Another significant benefit of the Kenmore 625.38826 and 625.38827 is their commitment to sustainability. By providing an effective alternative to bottled water, these filtration systems reduce plastic waste and promote environmentally friendly practices.

In summary, the Kenmore 625.38826 and 625.38827 stand out in the water filtration market with their robust multi-stage filtration process, user-friendly interface, and energy-efficient design. With an emphasis on providing pure, clean water, these models are an excellent choice for consumers looking to enhance their home water quality.
Top Page Image Contents