Safety Precautions

IMPORTANT SAFETY INFORMATION.

READ ALL INSTRUCTIONS BEFORE USING.

WARNING!	electric shock, property damage or personal injury.
	For your safety, the information in this manual must be followed to minimize the risk of

■Check and comply with your state and local codes. You must follow these guidelines.

■Use care when handling the water softening system. Do not turn upside down, drop, drag, or set on sharp protrusions.

■Water softening systems using sodium chloride (salt) for regeneration add sodium to the water. Persons on sodium restricted diets should consider the added sodium as part of their overall intake. Potassium chloride can be used as an alternative to sodium chloride.

■The water softening system works on 24 volt-60 Hz electrical power only. Be sure to use only the included transformer.

■Keep the salt hole cover in place on the softener unless servicing the unit or refilling with salt.

WARNING: Do not use with water that is microbiologically unsafe or of unknown quality without adequate disinfection before or after the system.

PROPER INSTALLATION

This water softening system must be properly installed and located in accordance with the Installation Instructions before it is used.

■Install or store where it will not be exposed to temperatures below freezing or exposed to any type of weather. Water freezing in the system will break it. Do not attempt to treat water over 100°F.

■Do not install in direct sunlight. Excessive sun heat may cause distortion or other damage to non-metallic parts.

■Properly ground to conform with all governing codes and ordinances.

■Use only lead-free solder and flux for all sweat-solder connections, as required by state and federal codes.

■The water softening system requires a minimum water flow of three gallons per minute at the inlet. Maximum allowable inlet water pressure is 125 psi. If daytime pressure is over 80 psi, nighttime pressure may exceed the maximum. Use a pressure reducing valve to reduce the flow if necessary.

■Softener resins may degrade in the presence of chlorine above 1 ppm. If you have chlorine in excess of this amount, you may experience less life of the resin. In these conditions, you may wish to consider purchasing a GE point-of-entry household filtration system with a chlorine reducing filter. Contact the GE Answer Center at 1-800-626-2000 for more information.

WARNING: Discard all unused parts and packaging material after installation. Small parts remaining after the installation could be a choke hazard.

READ AND FOLLOW THIS SAFETY INFORMATION CAREFULLY.

SAVE THESE INSTRUCTIONS

GXSF27B, GXSF39B, GNSF18Z01, GNSF35Z01 specifications

Diamond Power Products is well-known for its innovative solutions in the field of industrial equipment, and its GNSF35Z01, GNSF18Z01, GXSF39B, and GXSF27B models stand out for their advanced technologies and robust features. Each of these products is designed with a clear focus on enhancing performance, efficiency, and reliability in various industrial applications.

The GNSF35Z01 is notable for its exceptional power output and durability. It is engineered with a high-performance motor that ensures consistent operation even under demanding conditions. One of its key features is its energy-efficient design, which not only reduces operational costs but also minimizes environmental impact. Additionally, this model incorporates advanced cooling technologies to prevent overheating, thereby prolonging its lifespan and ensuring sustained productivity.

Similarly, the GNSF18Z01 is aimed at users who require a compact yet powerful solution. This model excels in versatility, making it suitable for a wide range of tasks. Its lightweight structure enables easy handling, while its robust construction guarantees durability. The GNSF18Z01 also features smart control technologies that optimize its performance, allowing operators to achieve precise results with minimal effort.

On the other hand, the GXSF39B model focuses on high throughput and efficiency. Its innovative design includes enhanced flow management systems that maximize performance during operation. This model is particularly favored in applications where speed and efficiency are critical. The GXSF39B is equipped with user-friendly interfaces, which simplify operation and maintenance, making it an indispensable tool in any industrial setting.

The GXSF27B is another significant addition to Diamond Power’s lineup. It is specially crafted to handle heavy-duty applications with ease. The robust frame and high-quality components ensure that it can withstand rigorous use. Its advanced safety features provide operators with peace of mind, knowing that operational safety is prioritized. This model also embraces modern technologies, such as IoT capabilities, allowing for real-time monitoring and data analysis, which can enhance decision-making processes.

In conclusion, the GNSF35Z01, GNSF18Z01, GXSF39B, and GXSF27B models from Diamond Power Products showcase cutting-edge technologies and exceptional features. These products exemplify the brand's commitment to providing reliable, efficient, and versatile solutions for the industrial sector, enabling businesses to operate at peak performance while meeting their environmental responsibilities. Whether for high efficiency, compact design, or heavy-duty applications, Diamond Power Products delivers equipment that aligns with the evolving needs of modern industries.