Diamond Power Products GXSF39B, GXSF27B Installation instructions, Unpacking and Inspection

Page 4

Installation instructions.

CAUTION: Certain plumbing skills are needed for installation. If you are unsure about any part of the installation of this product, consult a professional plumber.

Unpacking and Inspection

Be sure to check the entire softener for any shipping damage or parts loss. Also note damage to the

shipping cartons. Contact the transportation company for all damage and loss claims. The manufacturer is not responsible for damages in transit.

Small parts, needed to install the softener, are on a skin-packed cardboard piece. To avoid loss of the small parts, keep them on the skin-pack until you are ready to use them.

Important Installation Recommendations

Read entire manual. Failure to follow all guidelines and rules could cause personal injury or property damage.

Before you begin installation, read these Installation Instructions completely. Then, obtain all the materials and tools you will need to make the installation. Failure to properly install the softener voids the warranty.

Check local codes. The installation must conform to them.

In the Commonwealth of Massachusetts, Plumbing Code 248 CMR shall be adhered to. Consult with your licensed plumber.

Use only lead-free solder and flux for all sweat-solder connections, as required by state and federal codes.

Connect the softener to the main water supply pipe before or ahead of the water heater. DO NOT RUN HOT WATER THROUGH THE SOFTENER. Temperature of water passing through the softener must be less than 120° F.

Use care when handling the softener. Do not turn upside down, drop, drag, or set on sharp protrusions.

Maximum allowable inlet water pressure is 125 psi. If daytime pressure is over 80 psi, nighttime pressure may exceed the maximum. Use a pressure reducing valve if necessary. (Adding a pressure reducing valve may reduce the flow.)

The softener works on 24 volt-60 Hz electrical power only. Be sure to use the included transformer. Be sure the electric outlet and transformer are in an inside location to protect from wet weather.

See Where to Install the Softener section for more details.

WARNING: Do not use with water that is microbiologically unsafe or of unknown quality without adequate disinfection before or after the system. The water should be tested periodically to verify that the system is performing satisfactorily.

Small parts remaining after the installation could be a choke hazard. Discard safely.

4

Image 4
Contents Water Softening system GE & You, a Service Partnership Two easy ways to register your applianceSafety Precautions Important Installation Recommendations Installation instructionsUnpacking and Inspection Where to Install the Softener Plan How You Will Install the SoftenerTools and Materials Required for Installation Typical Installation Illustration Optional 3-Valve Bypass Installation IllustrationStep-by-step installation instructions Install Bypass ValveProgram the Control Programming the Control SmartWater Softener SystemSanitizing Procedures SPECIFICATIONS/DIMENSIONS GNSF18 GXSF27 GNSF35 GXSF39 About the water softener system Breaking a Salt Bridge Cleaning the Nozzle and Venturi Assembly Feature Optional Recharge Controls Feature Program MemoryFeature/Service Automatic Electronic Diagnostics Normal Operation, Control DisplaysTo remove an error code 1 Unplug transformer Service Timer/Softener, Service Checkout ProcedureERR Open a Nearby Soft Water Faucet If the water softening system does not draw brine, check Cleaning Iron Out of the Water Softening System Care and cleaning of the water softening systemChecking the Salt Storage Level and Refilling Before you call for service… Problem Possible Causes What To Do No soft waterAfter installation Water softening system Not using any saltAfter installation Water feels slipperyIs cloudy Error Code on control Resin beads showingUp in drinking water Sink Sounds you might hear Water has air bubblesPage Page We’ll Cover Any Appliance. Anywhere. Anytime Consumer Product Ownership Registration Parts list 153 Parts catalog Spacer GE Water Softening System Warranty For The Period GE Will ReplaceWhat GE Will Not Cover Warrantor General Electric Company. Louisville, KYService Telephone Numbers GE Answer Center

GXSF27B, GXSF39B, GNSF18Z01, GNSF35Z01 specifications

Diamond Power Products is well-known for its innovative solutions in the field of industrial equipment, and its GNSF35Z01, GNSF18Z01, GXSF39B, and GXSF27B models stand out for their advanced technologies and robust features. Each of these products is designed with a clear focus on enhancing performance, efficiency, and reliability in various industrial applications.

The GNSF35Z01 is notable for its exceptional power output and durability. It is engineered with a high-performance motor that ensures consistent operation even under demanding conditions. One of its key features is its energy-efficient design, which not only reduces operational costs but also minimizes environmental impact. Additionally, this model incorporates advanced cooling technologies to prevent overheating, thereby prolonging its lifespan and ensuring sustained productivity.

Similarly, the GNSF18Z01 is aimed at users who require a compact yet powerful solution. This model excels in versatility, making it suitable for a wide range of tasks. Its lightweight structure enables easy handling, while its robust construction guarantees durability. The GNSF18Z01 also features smart control technologies that optimize its performance, allowing operators to achieve precise results with minimal effort.

On the other hand, the GXSF39B model focuses on high throughput and efficiency. Its innovative design includes enhanced flow management systems that maximize performance during operation. This model is particularly favored in applications where speed and efficiency are critical. The GXSF39B is equipped with user-friendly interfaces, which simplify operation and maintenance, making it an indispensable tool in any industrial setting.

The GXSF27B is another significant addition to Diamond Power’s lineup. It is specially crafted to handle heavy-duty applications with ease. The robust frame and high-quality components ensure that it can withstand rigorous use. Its advanced safety features provide operators with peace of mind, knowing that operational safety is prioritized. This model also embraces modern technologies, such as IoT capabilities, allowing for real-time monitoring and data analysis, which can enhance decision-making processes.

In conclusion, the GNSF35Z01, GNSF18Z01, GXSF39B, and GXSF27B models from Diamond Power Products showcase cutting-edge technologies and exceptional features. These products exemplify the brand's commitment to providing reliable, efficient, and versatile solutions for the industrial sector, enabling businesses to operate at peak performance while meeting their environmental responsibilities. Whether for high efficiency, compact design, or heavy-duty applications, Diamond Power Products delivers equipment that aligns with the evolving needs of modern industries.